MSZ-FS Installation Manual

ManualsBrandsMitsubishi ManualsCoolingWall Mounted 5-Zone System - 48,000 BTU Outdoor - 6k + 6k + 9k + 12k + 12k Indoor - 23.0 SEER

1-1. THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY

• Be sure to read these safety precautions and instructions.

 %HVXUHWRREVHUYHWKHZDUQLQJVDQGFDXWLRQVVSHFL¿HGKHUH

• After reading this manual, be sure to store it with the OPERATING INSTRUCTIONS for future reference.

• Please report to your supply authority or obtain their consent before connecting this equipment to the power supply system.

JG79J820H01

ENGLISH

Required Tools for Installation

Phillips screwdriver

Level

Scale

Utility knife or scissors

3 in. (75 mm) hole saw

Torque wrench

Wrench (or spanner)

5/32 in. (4 mm) hexagonal

wrench

Flare tool for R410A

Gauge manifold for R410A

Vacuum pump for R410A

Charge hose for R410A

Pipe cutter with reamer

MSZ-FS06/09/12/15/18NA

When installing multi units, refer to the

installation manual of the multi unit for

outdoor unit installation.

■ Do not install the unit by yourself (user).

 ,PSURSHURULQFRPSOHWHLQVWDOODWLRQFRXOGFDXVH¿UHHOHFWULFVKRFNLQMXU\GXHWR

WKHXQLWIDOOLQJRUZDWHUOHDNDJH&RQVXOWDTXDOL¿HGLQVWDOOHURUWKHGHDOHUIURP

whom you purchased the unit.

■ Follow the instructions detailed in the installation manual.

 ,QFRPSOHWHLQVWDOODWLRQFRXOGFDXVH¿UHRUHOHFWULFVKRFNLQMXU\GXHWRWKHXQLWIDOO-

ing, or leakage of water.

■ When installing the unit, use appropriate protective equipment and tools for

safety.

Failure to do so could cause injury.

■ Install the unit securely in a place that can bear the weight of the unit.

If the installation location cannot bear the weight of the unit, the unit could fall

causing injury.

■ Do not alter the unit.

 ,WPD\FDXVH¿UHHOHFWULFVKRFNLQMXU\RUZDWHUOHDNDJH

■ Perform electrical work according to the installation manual and be sure to use

an exclusive circuit. Do not connect other electrical appliances to the circuit.

 ,IWKHFDSDFLW\RIWKHSRZHUFLUFXLWLVLQVXI¿FLHQWRUWKHUHLVLQFRPSOHWHHOHFWULFDO

ZRUNLWFRXOGUHVXOWLQD¿UHRUDQHOHFWULFVKRFN

■ Ground the unit correctly.

Do not connect the ground wire to a gas pipe, water pipe, lightning rod or

telephone ground. Defective grounding could cause electric shock.

If required, take measures against leakage current.

■ Do not damage the wires.

 'DPDJHGZLUHVFRXOGFDXVH¿UH

■ Be sure to shut off the main power when setting up the indoor P.C. board or

wiring.

Failure to do so could cause electric shock.

■ 8VHWKHVSHFL¿HGZLUHVWRVHFXUHO\FRQQHFWWKHLQGRRUDQGRXWGRRUXQLWV$W-

WDFKWKHZLUHV¿UPO\WRDYRLGDSSO\LQJVWUHVVWRWKHWHUPLQDOEORFN

 ,PSURSHUFRQQHFWLRQFRXOGFDXVH¿UH

■ 'RQRWLQVWDOOWKHXQLWLQDSODFHZKHUHÀDPPDEOHJDVPD\OHDN

If gas leaks and accumulates around the unit, it could cause an explosion.

■ Do not use intermediate connection of the power cord or the extension cord.

Do not connect many devices to one AC outlet.

 ,WFRXOGFDXVHD¿UHRUDQHOHFWULFVKRFN

■ 8VHWKHSDUWVSURYLGHGRUVSHFL¿HGSDUWVIRUWKHLQVWDOODWLRQZRUN

 7KHXVHRIGHIHFWLYHSDUWVFRXOGFDXVHDQLQMXU\RUOHDNDJHRIZDWHUGXHWRD¿UH

an electric shock, the unit falling, etc.

■ When plugging the power supply plug into the outlet, make sure that there is

no dust, blockage, or loose parts both in the outlet and on the plug. Verify that

the power supply plug is completely in the outlet.

If there is dust, blockage, or loose parts on the power supply plug or the outlet, it could

FDXVHHOHFWULFVKRFNRU¿UH,IORRVHSDUWVDUHIRXQGRQWKHSRZHUVXSSO\SOXJUHSODFHLW

■ Securely attach the electrical cover to the indoor unit and the service panel to

the outdoor unit.

If the electrical cover of the indoor unit and/or the service panel of the outdoor unit are

QRWDWWDFKHGVHFXUHO\GXVWZDWHUHWFFRXOGFROOHFWLQWKHXQLWDQGFRXOGFDXVHD¿UHRU

an electric shock.

■ When installing, relocating, or servicing the unit, make sure that no substance

RWKHUWKDQWKHVSHFL¿HGUHIULJHUDQW5$HQWHUVWKHUHIULJHUDQWFLUFXLW

Any presence of foreign substance such as air can cause abnormal pressure rise

and may result in explosion or injury. The use of any refrigerant other than that

VSHFL¿HGIRUWKHV\VWHPZLOOFDXVHPHFKDQLFDOIDLOXUHV\VWHPPDOIXQFWLRQRUXQLW

breakdown. In the worst case, this could lead to a serious impediment to securing

product safety.

■ Do not discharge the refrigerant into the atmosphere. Check that the refriger-

ant gas does not leak after installation has been completed. If refrigerant leaks

during installation, ventilate the room.

 ,IUHIULJHUDQWFRPHVLQFRQWDFWZLWKD¿UHKDUPIXOJDVFRXOGEHJHQHUDWHG

 ,IUHIULJHUDQWJDVOHDNVLQGRRUVDQGFRPHVLQWRFRQWDFWZLWKWKHÀDPHRIDIDQ

heater, space heater, stove, etc., harmful gases will be generated.

■ Use appropriate tools and piping materials for installation.

The pressure of R410A is 1.6 times higher than R22. Not using the appropriate

tools and materials, or improper installation could cause the pipes to burst causing

an injury.

■ When pumping down the refrigerant, stop the compressor before disconnecting

the refrigerant pipes.

If the refrigerant pipes are disconnected while the compressor is running and the

stop valve is open, air could be drawn in and the pressure in the refrigeration cycle

could become abnormally high, causing the pipes to burst.

■ When installing the unit, securely connect the refrigerant pipes before starting

the compressor.

If the compressor is started before the refrigerant pipes are connected and the

stop valve is open, air could be drawn in and the pressure in the refrigeration cycle

could become abnormally high, causing the pipes to burst.

■ )DVWHQDÀDUHQXWZLWKDWRUTXHZUHQFKDVVSHFL¿HGLQWKLVPDQXDO

 ,IIDVWHQHGWRRWLJKWDÀDUHQXWFRXOGEUHDNDQGFDXVHUHIULJHUDQWOHDNDJH

■ Install the unit according to national wiring regulations.

■ When opening or closing the valve below freezing temperatures, refrigerant may

spurt out from the gap between the valve stem and the valve body, resulting in

injuries.

■ Please follow applicable federal, state, or local codes to prevent potential

leakage/electric shock. Or install a ground fault interrupt for the prevention of

leakage and electric shock.

■ Perform the drainage/piping work securely according to the installation manual.

If there is defect in the drainage/piping work, water could drip from the unit, and

damage household items.

■ 'RQRWWRXFKWKHDLULQOHWRUWKHDOXPLQXP¿QVRIWKHRXWGRRUXQLW

This could cause injury.

■ Do not install the outdoor unit where small animals may live.

If small animals enter the unit and damage its electrical parts, it could cause a

PDOIXQFWLRQVPRNHHPLVVLRQRU¿UH.HHSWKHDUHDDURXQGWKHXQLWFOHDQ

CAUTION

(Could lead to serious injury when operated incorrectly.)

WARNING

(Could lead to death or serious injury.)

SPLIT-TYPE AIR CONDITIONERS

INSTALLATION MANUAL

1. BEFORE INSTALLATION

Summary of content (8 pages)

PAGE 1
ENGLISH JG79J820H01 MSZ-FS06/09/12/15/18NA SPLIT-TYPE AIR CONDITIONERS INSTALLATION MANUAL When installing multi units, refer to the installation manual of the multi unit for outdoor unit installation. Required Tools for Installation Phillips screwdriver 5/32 in. (4 mm) hexagonal Level wrench Flare tool for R410A Scale Gauge manifold for R410A Utility knife or scissors Vacuum pump for R410A 3 in. (75 mm) hole saw Charge hose for R410A Torque wrench Pipe cutter with reamer Wrench (or spanner) 1.
PAGE 2
1-2. SELECTING THE INSTALLATION LOCATION INDOOR UNIT :KHUH DLUÀRZ LV QRW EORFNHG • Where cool (or warm) air spreads over the entire room. • On a rigid wall to reduce the possibility of vibration. • Where it is not exposed to direct sunlight. Do not expose to direct sunlight also during the period following unpacking to before use. • Where it can be easily drained. • At a distance 3 ft. (1 m) or more away from a TV and radio.
PAGE 3
1-4. INSTALLATION DIAGRAM Use the wall hole sleeve (C) to prevent indoor/outdoor connecting wire (A) from contacting metal parts in the wall and to protect the wiring from rodents. ACCESSORIES Check the following parts before installation. Wall hole cover (D) (3) Wireless remote controller 1 (4) Felt tape (For left or left-rear piping) 1 (5) Remote controller holder 1 (6) Screws for the remote controller holder 3.
PAGE 4
2. INDOOR UNIT INSTALLATION 2-1. ATTACHING THE INSTALLATION PLATE )LQG D VWXG LQ WKH ZDOO WR DWWDFK LQVWDOODWLRQ SODWH KRUL]RQWDOO\ E\ WLJKWHQLQJ WKH ¿[LQJ VFUHZV ¿UPO\ • To prevent installation plate (1) from vibrating, be sure to install the attachment screws in the holes indicated in the illustration. For added support, additional screws may also be installed in other holes.
PAGE 5
2-4. PIPE FORMING AND DRAIN PIPING 2-4-1. PIPE FORMING • • • • Place the drain hose below the refrigerant piping. Make sure that the drain hose is not crowded or bent. Do not pull the hose when applying the tape. When the drain hose passes the room, be sure to wrap it with insulation material ¿HOG VXSSOLHG Note: Make sure not to damage the cover of refrigerant pipe when attaching it back on with screws.
PAGE 6
3. OUTDOOR UNIT INSTALLATION 3-1. CONNECTING WIRES FOR OUTDOOR UNIT 1) Remove the service panel. 2) Remove the conduit cover. 3) Attach the conduit connectors to the conduit plate with lock nuts then secure it against unit with screws. 4) Connect the ground wires of indoor/outdoor unit connecting wire (A) and power supply cord (K) to the TB support.
PAGE 7
3-3. PIPE CONNECTION )DVWHQ ÀDUH QXW ZLWK D WRUTXH ZUHQFK DV VSHFL¿HG LQ WKH WDEOH UHIHU WR :KHQ IDVWHQHG WRR WLJKW ÀDUH QXW PD\ HYHQWXDOO\ EUHDN DQG FDXVH UHIULJHUDQW OHDNDJH • Be sure to wrap insulation around the piping. Direct contact with the bare piping may result in burns or frostbite. Indoor unit connection Connect both liquid and gas pipings to indoor unit. $SSO\ D WKLQ FRDW RI UHIULJHUDWLRQ RLO - RQ WKH ÀDUHG HQGV RI WKH SLSHV 'R QRW DSSO\ UHfrigeration oil on screw threads.
PAGE 8
5. RELOCATION AND MAINTENANCE 5-1. REMOVING AND INSTALLING THE PANEL ASSEMBLY Removal procedure and using a thin instrument. 1) Unlock the upper and lower vanes as shown in Then, remove the horizontal vanes. 2) Remove the front panel. 5HPRYH WKH VFUHZV ZKLFK ¿[ WKH SDQHO DVVHPEO\ 4) The panel assembly consists of 3 components. Remove them in the following order: right, left, and center bottom. To remove the right component, pull out the right top corner.