AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR USER’S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. Internet Home Page: http://www.mitsubishi-electric.com.au/ ® Supplying Windows 95/98/2000 INF File download service, new product information, etc.
- ii -
RADIO INTERFERENCE REGULATIONS STATEMENT FOR U.S.A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.se Current information regarding TCO’99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.
CONTENTS 1. INTRODUCTION ................................................... 2 CAUTION 1.1 Features ...................................................... 2 1.2 Internal Preset Memory Capability .............. 3 The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. 1.3 Power Management Function ..................... 3 1.4 DDC ............................................................ 3 1.
1 INTRODUCTION Congratulations on your purchase of this high resolution color monitor. We designed this monitor to provide you with years of reliable trouble-free operation. This guide tells you how to connect, adjust and care for your monitor. This guide also provides technical specifications and instructions for troubleshooting any basic problems you may experience with your monitor. 1.
1.2 Internal Preset Memory Capability 1.5 When setting up and using the monitor, keep the following in mind: To minimize adjustment needs, the factory has preset popular display standards into the monitor, as shown in Table 1. If any of these display standards are detected, the picture size and position are automatically adjusted. All of the factory presets may be overwritten by adjusting the user controls. This monitor is capable of automatically storing up to 24 additional display standards.
1.7 1.9 Quick Operation Chart Unpacking To summarize the steps in connecting your computer with the color monitor and setting the necessary controls and switches, refer to the chart below. After you unpack the box you should have all of the items indicated in Figure 1. Save the box and packing materials in case you transport the monitor. 1 2 Connect the color monitor and computer with the necessary cords and cables. See Section 3. INSTALLATION AND CONNECTION Turn on the color monitor.
2 PART NAME 2.1 Control Names See Figures 3 and 4 for the location of the user controls, indicator and connectors. Each part is identified by number and is described individually. REAR FRONT SELECT RESET Figure 3 2.2 Figure 4 Function 5. AC POWER CONNECTOR 1. POWER SWITCH: A push-on / push-off switch for AC power. 6. SIGNAL INPUT CONNECTOR: DB9-15P 2.
3 INSTALLATION AND CONNECTION 3.2.2 Connecting to An Apple Macintosh Computer On the back of the monitor two kinds of plug-in connections are provided: AC power connector for the AC input, DB915P connector for video signal input. 3.1 Figure 6 shows the signal cable and Adapter (option) to the video port in an Apple Macintosh.
4 4.1 OSD (On Screen Display) FUNCTIONS How to adjust the screen The monitor has an OSD(On Screen Display) function. The following procedure shows how to adjust the screen using the OSD function.
4.2 Adjustment Items X: Available Press the Plus Button Press the Minus Button Item Icon Item Brightness Contrast To decrease the brightness. To increase the brightness. To decrease the contrast. To increase the contrast. A B X X X X NOTE Without OSD screen, push to adjust the contrast. To decrease the red contrast. To increase the red contrast. X X To decrease the green contrast. To increase the green contrast. X X Blue Color Control To decrease the blue contrast.
5 TROUBLESHOOTING ITEMS TO CHECK PROBLEM No picture Before calling your Authorized Product Support, please check that the items below are properly connected or set. In case of using a non-standard signal, please check the pin assignments and the signal timing of your computer with the specification outlined in Section 6. SPECIFICATIONS.
ITEMS TO CHECK PROBLEM Two fine horizontal lines are visible on the screen. LOCATION • The 2 very faint thin lines across the screen are normal. They are caused by the aperture grille stabilization filaments(Damper Wires) which are required for all aperture grille CRTs’. Aperture Grille Shadow of Damper Wires Electrn Gun Damper Wires Shadow of Damper Wires A buzzing sound when power on. Aperture Grille Type • A brief vibration or hum sound that is heard just after power up is normal.
6 SPECIFICATIONS Size CRT 43cm/17" (41cm/16" Viewable Image Size) Mask type Aperture grille Gun In-line Deflection angle 90° Phosphors Red, Green, Blue EBU (medium short persistence) Aperture grille pitch 0.25mm Face Plate Anti-glare, Anti-reflection and Anti-static film Focusing method Dynamic Beam Forming (DBF) INPUT SIGNAL Video Sync 0.7V analog RGB Separate H, V sync., or Composite sync SIGNAL INTERFACE Input Connectors Input Impedance DB9-15P 75Ω (video), 2.2kΩ(sync.
7 WARRANTY IMPORTANT Please keep this Warranty in a safe place. It is valuable. The benefits conferred by this Warranty are in addition to all other rights and remedies in respect of the product which the consumer has under the Trade Practices Act and similar State and Territory Laws. PC and GRAPHIC MONITORS MITSUBISHI 3 YEAR WARRANTY Please complete and keep with original purchase docket.
b) c) d) e) 3. a) b) c) the product is damaged by the use of a consumable which is not supplied by Mitsubishi Electric Australia or its recognised retailer and which consumable is not of an equivalent standard and quality. the product is damaged by exhausted, leaking or used batteries or fails to function correctly as a result of the use of such batteries.
IMPORTANT NOTICE This recycle symbol may appear on packaging material or components of this product. Cd This symbol is a mandatory requirement in some countries and does not necessarily indicate that the material can be recycled in Australia. The Plastic Identification Code (numbers 1 to 7 in a “chasing arrows triangle”) may also appear on packaging material or components for this product. 1 This symbol is designed to identify the resin type used in the manufacture of the material on which it appears.
- 15 -
15500991 Declaration of Conformity - United States only Product Name: Type: Brand Name: 17 in. (43cm) Color Display Monitor N0701 MITSUBISHI This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.