Contents 1. 2. 3. 4. 5. 6. Safety Precautions ................................................................2 Parts Names..........................................................................2 Screen Configuration.............................................................5 Setting the Day of the Week and Time ..................................5 Operation...............................................................................5 Timer ............................................................
2. Parts Names Wired Remote-Controller “Sensor” indicator Display Section For purposes of this explanation, all parts of the display are shown as lit. During actual operation, only the relevant items will be displayed. Identifies the current operation Displayed when the remote controller sensor is used. Day-of-Week Shows the current day of the week. Time/Timer Display “Locking function” indicator Shows the current time, unless the simple or Auto Off timer is set.
2. Parts Names Wireless Remote-Controller Transmission area Transmission indicator Remote controller display Timer indicator * For explanation purposes, all of the items that appear in the display are shown. * All items are displayed when the Reset button is pressed.
3. Screen Configuration Function Selection of remote controller Set Day/Time TIME SUN A D C Standard Control Screens °F°C °C OFF ON B C Timer Monitor Timer Setup MON SUN MON TUE WED THU FRI SAT TIMER OFF B °F°C WEEKLY WEEKLY For details on setting the language for the remote controller display, refer to section 8. Function Selection. The initial language setting is English.
5. Operation Press the ON/OFF button 1 again. • The ON lamp 1 and the display area go dark. Note: Even if you press the ON/OFF button immediately after shutting down the operation is progress, the air conditioner will not start for about three minutes. This is to prevent the internal components from being damaged. 5.2. Operation mode select Press the operation mode ( operation mode 2. ) button 2 and select the 5.4.
5. Operation 5.5. Airflow up/down direction setting 5.6. Ventillation With the unit running, press the Airflow up/down button 6 as necessary. • Each press changes the direction. The current direction is shown at 6. • The change sequence, and the available settings, are as follows. Airflow Wireless remote controller Swing Swing 1 Auto 2 1 2 3 3 To run the ventilator together with the indoor unit: Press the ON/OFF button 1.
6. Timer 6.1. For Wired Remote-controller You can use Function Selection of remote controller to select which of three types of timer to use: 1 Weekly timer, 2 Simple timer, or 3 Auto Off timer. 6.1.1. Weekly Timer The weekly timer can be used to set up to eight operations for each day of the week. • Each operation may consist of any of the following: ON/OFF time together with a temperature setting, or ON/OFF time only, or temperature setting only.
6. Timer 7. Press the appropriate Temperature set button 3 to set the desired temperature (at 7). * Each press changes the setting, in the following sequence: No display (no setting) ⇔ 24 ⇔ 25 ⇔ ... ⇔ 29 ⇔ 30 ⇔ 12 ⇔ ... ⇔ 23 ⇔ No display. (Available range: The range for the setting is 12 °C to 30 °C. The actual range over which the temperature can be controlled, however, will vary according to the type of the connected unit.) 8.
6. Timer 7. After completing steps 3 to 6 above, press the Filter lock in the value. button 4 to Note: Your new settings will be cancelled if you press the Operation mode (Back) button 2 before pressing the Filter button 4. Example 2: Start the timer, with OFF time is sooner than ON time ON Setting: 5 hours OFF Setting: 2 hours Hr AFTER OFF 8. Press the Operation mode (Back) button 2 to return to the standard control screen. 9. Press the Timer On/Off button 9 to start the timer countdown.
6. Timer 6.2. For wireless remote controller 4 5 Timer Setting TIMER AFTER OFF A 1 AUTO OFF 1. Be sure that the “Auto Off” is visible on the screen (at 1). 2. Hold down the Timer Menu button b for 3 seconds, so that “Monitor” is indicated on the screen (at 4). • The timer remaining to shutdown appears at 5. 3. To close the monitor and return to the standard control screen, press the Operation mode (Back) button 2. 13
7. Other Functions 7.2. Error Codes indication ERROR CODE ON/OFF Indoor Unit’s Refrigerant Address Error Code ON lamp (Flashing) Indoor Unit No. Alternating Display If you have entered contact number to be called in the event of a problem, the screen displays this number. (You can set this up under Function Selection of remote controller. For information, refer to section 8.
8. Function Selection Normal display (Display when the air condition is not running) [Function selection flowchart] Setting language (English) Hold down the E button and press the D button for 2 seconds. E Press the operation mode button. G Press the TIMER MENU button. D Press the TIMER ON/OFF button. Hold down the E button and press the D button for 2 seconds. Remote controller function selection mode Item1 G Change Language Item2 Dot display English G Germany E F Spanish TEMP.
8. Function Selection [Detailed setting] [4]–1. CHANGE LANGUAGE setting The language that appears on the dot display can be selected. • Press the [ MENU] button G to change the language. 1 English (GB), 2 German (D), 3 Spanish (E), 4 Russian (RU), 5 Italian (I), 6 Chinese (CH), 7 French (F), 8 Japanese (JP) Refer to the dot display table. [4]–2. Function limit (1) Operation function limit setting (operation locking function) • To switch the setting, press the [ ON/OFF] button D.
8.
9. Emergency Operation for Wireless Remote-controller [Combination Cooling and Heating Models] Cooling Heating Stop PKA-RP·KAL C B A D [Cooling Only Models] Cooling Stop Operation Monitor Display When the remote controller cannot be used When the batteries of the remote controller run out or the remote controller malfunctions, the emergency operation can be done using the emergency buttons on the grille.
11. Troubleshooting Having trouble? Air conditioner does not heat or cool well. When heating operation starts, warm air does not blow from the indoor unit soon. During heat mode, the air conditioner stops before the set room temperature is reached. Airflow up/down direction changes during operation or airflow up/down direction cannot be set. When the airflow up/down direction is changed, the vanes always move up and down past the set position before finally stopping at the position.
11. Troubleshooting Having trouble? Noise is louder than specifications. Here is the solution. (Unit is operating normally.) The indoor operation sound level is affected by the acoustics of the particular room as shown in the following table and will be higher than the noise specification, which was measured in an echo-free room. High soundNormal rooms Low soundabsorbing rooms absorbing rooms Location Broadcasting Reception room, Office, hotel examples studio, music hotel lobby, etc. room room, etc.
Please be sure to put the contact address/telephone number on this manual before handing it to the customer. HEAD OFFICE: TOKYO BLDG.
