Engineering Manual
24
Unit: mm (inch)
PEAD-A12AA7 PEAD-A18AA7 PEAD-A24AA7
PEAD-A30AA7 PEAD-A36AA7 PEAD-A42AA7
200(7-7/8)
120°
120°
ø125
135
378(14-15/16) 153(6-1/16)
B(Suspension bolt pitch)23(15/16)
C
A
40(1-5/8)
15(5/8)
40(1-5/8)
58(2-5/16)
20(13/16) D(Duct)
30(1-3/16) 100(3-15/16)X(E-1)=F
100(3-15/16)
10(7/16)
57(2-1/4) 643(25-3/8)
18(3/4) 210(8-5/16)
21(7/8)
G
732(28-7/8)
32(1-5/16)
700(27-9/16)
238(9-3/8)
10(7/16)
33(1-5/16)
40(1-5/8)
100(3-15/16)
122(4-13/16)
178(7-1/16)
136 67
356(14-1/16)
217(8-9/16)
41(1-5/8)
250(9-7/8)
23(15/16)
H±3(H±1/8)
J±3(J±1/8)
(4-15/16)
(5-3/8)
3-ø2.9(1/8) mount hole
Drain pipe(O.D ø32(1-1/4))
Fresh air intake ø100(3-15/16)
knock out hole
2XE-ø2.9(1/8)
(Suspension bolt pitch)
Air filter
Drain pipe
(Integral lift pump outlet)
Drain pump
(DUCT)
1Refrigerant piping (gas)
(5-3/8)
(2-11/16)
(Emergency drain)
2Refrigerant piping(liquid)
Drain pipe(O.Dø32(1-1/4))(Gravity drain)
Terminal block(Power source)
Terminal block(Transmission)
Note 4
Control box
(O.Dø32(1-1/4))
Top
Top
Bottom
view
Top
Bottom
Inlet air
side view
Outlet air
side view
Opposite piping
side view
Piping
side view
2X2-ø2.9(1/8)
(43-5/16)
(55-1/8)
(45-7/16)
(57-1/4) (59-1/16) (53-9/16)
(47-1/4) (41-3/4)(39-3/8)
(51-3/16)
(41-11/16)
(53-1/2)
2Liquid pipe1Gas pipe
1058
13581300
Model
1200
11
10601100 1154
1400
ø15.88
(5/8)
1454
1500
ø9.52
(3/8)
1360
14
1000
PEAD-A24,30AA7
PEAD-A36,42AA7
Unit:mm(in.)
Air
inlet
Air
outlet
Note 1.Use an M10 screw for the suspension bolt
(field supply).
2.Keep the service space for maintenance
at the bottom.
3.This drawing is for PEAD-A24·30·36·42
AA7 models,which have 2 fans. PEAD-A12·
18AA7 models have 1 fan.
4.If the inlet duct is used,remove the air
filter (supplied with the unit), then
install the filter (field supply) at the
suction side.
5.Heat air to 0˚C (32˚F) or higher when
taking fresh air with a fresh air intake.
PEAD-A24,30AA7
PEAD-A36,42AA7
PEAD-A12,18AA7
Model AEDC
BF
G
Unit:mm(in.)
(35-7/16) (37-9/16)(39-3/8) (33-7/8)(31-1/2)(33-13/16)
8581000
9
860 900 954 800
PEAD-A12,18AA7
ø12.7
(1/2)
ø6.35
(1/4)
(3-1/8)
78
H
(2-7/8)
72
J
(2-5/8)
66
(2-1/2)
62