MERV 14 Operation Manual

2107874HM5801
PZ-50RF9-E・PZ-65RF9-E
PZ-80RF
9-E・PZ-100RF9-E
The Filters are supplied for replacing with the air filters built in your commercial use Lossnay ventilator.
■For applicable models and quantities required, refer to the separate delivery specifications, products brochure, etc.
■Please read through these instructions in order to familiarize yourself with the proper and safe procedures for
operating the Lossnay. After reading this manual, keep it in an easily accessible and safe place for future reference.
Outline drawings
Safety precautions
Assembly after maintenance
Model
PZ-50RF
9-E
PZ-65RF
9-E
PZ-80RF
9-E
PZ-100RF
9-E
A
18 1/2 (470)
17 3/64 (433)
17 3/4 (451)
22 1/4 (565)
B
7 13/64 (183)
8 37/64 (218)
9 9/16 (243)
9 9/16 (243)
C
25/32 (20)
25/32 (20)
25/32 (20)
25/32 (20)
Number of filters
per set
4
4
4
4
Applicable models
TLGHF0300RVX02A, LGH-F300RVX2-E
TLGHF0380RVX02A, LGH-F380RVX2-E
TLGHF0470/0940RVX02A, LGH-F470/940RVX2-E
TLGHF0600/1200RVX02A, LGH-F600/1200RVX2-E
■Dimensions
Unit: in (mm)
(For the user)
FILTER FOR MITSUBISHI ENERGY RECOVERY VENTILATOR LOSSNAY
Models:
Operating Instructions
●
Wear gloves when installing and
maintaining the filter.
Otherwise, edges may cause injury.
●
Make sure the power supply isolator
is turned off before installing and
maintenance filters.
Failure to heed this warning may result in
electric shock or injury.
The following symbols denote the danger and its degree that may result from incorrect use.
Incorrect handling could cause
injury or damage to property or
household effects.
Incorrect handling could cause
serious injury or death.
CAUTION
CAUTION
WARNING
Important
*The filters are comprised of one set of the same
filters as those built in the product.
Two sets of filters can be installed in one unit of
F940R and F1200R.
A
B
C
Maintenance
(2) Take hold of the handle and draw the Lossnay
cores out from the main unit.
(3) After pulling out the Lossnay cores, remove filter
guides, then remove the air filters, located at the
bottom left and right of the Lossnay cores, as
below.
(4) Use a vacuum cleaner to remove light dust.
To remove stubborn dirt wash in a mild solution of
detergent and lukewarm water. (under 107°F (40°C))
Air filter
Air filter
●
The Maintenance cover must be removed.
CAUTION
Note
●
When Lossnay unit is installed upside down, air filters
are located at the upper right and left of the Lossnay
cores.
Clean the air filters once a year in order to prevent a deterioration in the Lossnay functions.
(Frequency should be increased depending on the extent of dirt.)
Lossnay core
(1) Locate and remove the cover fixing screw. Pull back
the hinge, open the Maintenance cover and lift off
the hinge bracket.
Maintenance cover
Hinge
Hinge bracket
Handle
Main unit
Filter stopper
Filter guide
●
Bow filter stoppers a little to remove them from
filter guide.
●
Take filter stoppers careful not to break them.
CAUTION
●
Never wash the filters in very hot water and
never wash them by rubbing them.
●
Do not dry the filters by exposing them to a
flame.
Vacuum cleaner
Air filter
Bearing in mind the following points, assemble the parts
following the sequence for their removal in reverse.
●
Arrange the Lossnay core with the air filter side as
shown in the name plate on the Lossnay unit.
●
The filters have front and back side. Set the “FRONT”
(printed) side of the filter on the outer side.
Note
●
If filter cleaning sign is indicated on the
remote controller, turn off the indication, after
maintenance.
2-7-3 Marunouchi, Chiyoda-ku, Tokyo, 100-8310 Japan
Prohibited