Web Server Module User's Manual (Installation) QJ71WS96 Thank you for purchasing the Mitsubishi programmable logic controller MELSEC-Q Series. Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.
z SAFETY PRECAUTIONS z (Be sure to read these instructions before using the product.) Before using this product, read this manual and the relevant manuals introduced in this manual carefully and handle the product correctly with full attention to safety. Note that these precautions apply only to this product. Refer to the user's manual of the CPU module for the PLC system safety precautions. In this manual, the safety instructions are ranked as "DANGER" and "CAUTION".
[DESIGN PRECAUTIONS] CAUTION z Do not bundle the control lines or communication cables with the main circuit or power lines, or bring them close to each other. The distance of 100mm(3.9inch) or more should be ensured. Failure to do so cause malfunctions due to noise. z Do not power off a station where this module is mounted and do not reset the PLC CPU while storing the settings into the standard ROM of the module using a Web browser.
[WIRING PRECAUTIONS] CAUTION z Be sure to fix communication cables and power cables to the module by ducts or clamps. Failure to do so may cause damage of the module or the cables due to accidental pull or unintentional shifting of the cables, or malfunctions due to poor contact of the cable. z Connect the connectors to the module securely. z Tighten the terminal screws within the specified torque range. Loose tightening may result in a fall, short circuits or malfunctions.
Revisions * The manual number is given on the bottom left of the back cover. Print Date *Manual Number Revision July, 2002 IB(NA)-0800231-A First printing Nov., 2002 IB(NA)-0800231-B Correction Section 3.1(2), Chapter 4, Section 5.2(2) Nov., 2003 IB(NA)-0800231-C Correction Chapter 2, Chapter 6 Addition Safety Precautions, Section 3.1 (2), Chapter 8 This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses.
CONTENTS 1. Overview........................................................................................................ 1 2. Performance Specifications ........................................................................... 2 3. Mounting and Installation ............................................................................... 3 3.1 Handling Precautions ............................................................................... 3 3.2 Installation Environment ..............................
Manuals The following table lists the manual on this product. You can order it as necessary. Relevant Manual Manual name Web Server Module User's manual Manual No.
1. Overview This manual explains how to install the QJ71WS96 Web server module (hereinafter referred to as Web server module) and how to wire them with other devices.
2. Performance Specifications The following describes the performance specifications of the Web server module. For the general specifications of the Web server module, refer to the user's manual of the CPU module used.
3. Mounting and Installation 3.1 Handling precautions (1) Do not drop or apply severe shock to the module case since it is made of resin. (2) Always make sure to touch the grounded metal to discharge the electricity charged in the body, etc., before touching the module. Failure to do so may cause a failure or malfunctions of the module.
4.
Name 1) LED Display 10BASE-T/ 100BASE-TX interface 2) connection connector (RJ45) RS-232 interface 3) connection connector 4) EJECT button CompactFlashTM card mounting slot CompactFlashTM card 6) mounting slot cover 7) Battery 5) 8) Battery connector pin Description Refer (1) LED display contents. Used for connecting Web server module to 10BASE-T/100BASE-TX. (Web server module recognizes 10BASE-T/ 10BASE-TX according to the external device.) Used for connecting Web server module to RS-232.
5. External Wiring 5.1 Connecting to the 10BASE-T/100BASE-TX Use the twisted pair cable that meets IEEE802.3 10-BASE-T/100BASE-TX standards when connecting to the 10BASE-T/10BASE-TX interface. (1) For 100Mbps Use either of the following cables. (a) Unshielded twisted pair cable (UTP cable), Category 5 (b) Shielded twisted pair cable (STP cable), Category 5 (2) For 10Mbps Use either of the following cables.
5.2 Connecting to the RS-232 Use the RS-232 cable when connecting to the RS-232 interface. (1) RS-232 connector specifications 1 6 2 7 3 8 4 9 5 Pin No.
6. Setting from GX Developer Set the mode, default operation, battery error detection, logging monitor setting and response monitoring time for Web server module on the "Intelligent function module switch setting" screen.
(2) Default operation/Battery error detection setting/logging monitor setting (switch 2) b15 to Speccify 0. * b5 b4 b3 0 b2 b1 b0 Switch 2 Logging monitor setting Default operation setting (Account setting) 0: Not display the latest file update time. 0: Operates according to the account setting. 1: Operates according to the default setting.
(c) Logging monitor setting (bit 4) Whether the latest file update time is displayed or not in the file specification field of the logging monitor is set in this setting. 0: Not display the latest file update time. 1: Displays the latest file update time. (3) Response monitoring time setting (switch 3 (lower byte)) This is the setting for timeout time (second) from when a module sends a request to the CPU of the accessed device until the CPU responds to it.
98 (3.86) 7. External Dimensions R1 (*1) 27.4 (1.08) 14 (0.55) 90 (3.54) Cable diameter 4 + 10 R2 (*2) (Units:mm (in.)) *1: The bending radius near the connectors (reference value: R1) should be four times as long as the cable's outside diameter or more when connecting the twisted pair cable. *2: The bending radius near the connectors (reference value: R2) should be four times as long as the cable's diameter or more when connecting the RS-232 cable. CompactFlash is a trademark of SanDisk Corporation.
8. Transportation Precautions When transporting lithium batteries, make sure to treat them based on the transport regulations. 8.1 Controlled Models The lithium batteries used with the Web server module are classified as indicated in the following table: Product name Q series battery Model Q6BAT Product supply status Lithium battery Classification for transportation Non-dangerous goods 8.
Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi; damages to products other than Mitsubishi products; and to other duties.
