Indoor Installation Manual
Table Of Contents
- SVZ-KP12,18, 24, 30, 36NA
- Table of Contents
- SVZ-KP12,18, 24, 30, 36NA
- 1. Dimensions
- 2. Inspect shipment
- 3. Safety precautions
- 4. Indoor unit accessories
- 5. Selecting an installation site
- 6. Combining indoor units with outdoor units
- 7. Installing the unit
- 8. Side Return
- 9. Duct connection
- 10. Mount positions
- 11. Air filter
- 12. Refrigerant piping work
- 13. Drain connections
- 14. Electrical wiring
- 15. Test run
- SVZ-KP12,18, 24, 30, 36NA
- 1. Dimensions
- 2. Inspection du matériel livré
- 3. Mesures de sécurité
- 4. Accessoires de l’appareil intérieur
- 5. Sélection de l’emplacement d’installation
- 6. Combinaison des appareils intérieurs et extérieurs
- 7. Installation de l’appareil
- 8. Retour latéral
- 9. Raccordement des conduits
- 10. Positions de montage
- 11. Filtre à air
- 12. Travaux de tuyauterie de frigorigène
- 13. Raccordements de vidange
- 14. Câblage électrique
- 15. Essai de fonctionnement
- 15.1. Avant l’essai de fonctionnement
- 15.2. Essai de fonctionnement
- 15.3. Autotest
- 15.4. FONCTION D’AUTOREDÉMARRAGE
3.4. Before getting installed (moved)-electrical work
CAUTION
• Ground the unit.
– Do not connect the ground wire to gas or water pipes, lightning rods, or telephone
ground lines. Improper grounding may result in electric shock.
• Install the power cable so that tension is not applied to the cable.
– Tension may cause the cable to break and generate heat and cause a fire.
• Install a leak circuit breaker as required.
– If a leak circuit breaker is not installed, electric shock may result. Use power line ca-
bles of sufficient current carrying capacity and rating. Cables that are too small may
leak, generate heat, and cause a fire.
• Use power line cables of sufficient current carrying capacity and rating.
– Cables that are too small may leak, generate heat, and cause a fire.
• Use only a circuit breaker and fuse of the specified capacity.
– A fuse or circuit breaker of a larger capacity or a steel or copper wire may result in a
general unit failure or fire.
• Do not wash the air conditioner units.
– Washing them may cause an electric shock.
• Be careful that the installation base is not damaged by long use.
– If the damage is left uncorrected, the unit may fall and cause personal injury or proper-
ty damage.
• Install the drain piping according to this Installation Manual to ensure proper drainage.
Wrap thermal insulation around the pipes to prevent condensation.
– Improper drain piping may cause water leakage and damage to furniture and other
possessions.
• Be very careful about product transportation.
– If the product weighs more than 20 kg [44 lb], then more than one person should carry
the product.
– Some products use PP bands for packaging. Do not use any PP bands for a means of
transportation; it is dangerous.
– Do not touch the heat exchanger fins. Doing so may cut your fingers.
• Safely dispose of the packing materials.
– Packing materials, such as nails and other metal or wooden parts, may cause stabs or
other injuries.
– Tear apart and throw away plastic packaging bags so that children will not play with
them. If children play with a plastic bag which was not torn apart, they face the risk of
suffocation.
SVZ-KP12,18, 24, 30, 36NA
© 2022 Mitsubishi Electric US, Inc. 12 Specifications are subject to change without notice.
ENGLISH