namCOaAmerica Inc.
name0 UWE QX050STM 50 INCH Operator’s Manual TABLE OF CONTENTS 1.0 SPECIFICATIONS 1 2.0 INTRODUCTION 3 3.0 PRECAUTIONS 4 4.0 3.1 Installation 4 3.2 Handling 4 INSTALLATION 5 4.1 5.0 6.
name= TK=lE CWIJUSTM 50 INCH ODerator’s Manual 1 .O SPECIFICATIONS Logic Power Supply: Gun Power Supply: Input Power: Overall Height: 200 Watt switching type 24 VDC, 110 Watt 120 VAC, 60 Hz, 7 A m p s max. 95”, with marquee installed. Crated Dimensions: Monitor Player Cabinet Cabinet: Assy: 55”Wx41”Dx87”H 37.5” W x 48.
Operator’s Manual name= fUPiR~EKY~TM 50 INCH
namea UKE C.RUJll~TM 2.0 50 INCH Operator’s Manual INTRODUCTION TIME CRISIS is a revolutionary new l-player, 3-D polygon gun game featuring a new dual purpose “Action Pedal”. Players play the part of Richard Miller, a special agent assigned to rescue Rachel, the presidents daughter who is being held hostage by Sherudo Garo and his hired team of henchmen. Garo threatens to kill Rachel unless he is handed over the throne.
Onerator’s Manual 3.0 PRECAUTIONS 3.1 Installation This game is designed for indoor use only. following conditions must be avoided: name0 UUlilR WXSTM 50 INCH It must nor be installed outdoors. The 1. Direct exposure to sunlight, high humidity, direct water contact, dust, high heat or extreme cold. 2. Vibration. The game must be installed on a level surface with levelers properly adjusted. Do nof install in an area such that the game would present an obstacle in case of an emergency (i.e.
name= TUflE CR!XSTM 50 INCH Operator’s Manual 4.0 INSTALLATION Note: Shipping damage may void the warranty. In case of shipping damage, contact your distributor and the transportation carrier immediately. 1. Unpack the marquee and accessories box, and identify the following items: 1 ea 4 ea button head screws, M5 x 16.
Ooerator’s Manual 6 name0 VURIE CRUSEP’ 50 INCH 12. Perform the set up and test procedure. Once this has been successfully completed, reinstall the rear access panel. 13. (S/N 101-735 only) For best operation, perform an alignment of the 50 inch monitor. This procedure is outlined in the section entitled”Notes on 50 Inch Monitor”.
n a m e 0 TilflE CRUSUBTM 50 INCH 4.1 Operator’s Manual Set-Up and Test IMPORTANT: Pelform this procedure in the sequence indicated. 1. 2. 3. System initialization is performed as follows: a. Open the COIN door to gain access to the Service Panel b. Remove C. While pressing the SERVICE button, toggle the TEST switch ON. d. Release the SERVICE button. e. The GUN INITIALIZE Menu screen will appear as shown in Figure 1. f.
namco- Operator’s Manual TlFlZ CROXSTM 50 INCH f GUN INITIALIZE MENU (al GUN INITIALIZE [STANDARD] (b) GUN INITIALIZE [PmDVANCED] TEST SW OFF: SHOOT INSIDE SCREEN: SHOOT OUTSIDE SCREEN: STEP ON PEDAL: L !ZXIT CHOOSE [UP] CHOOSE [DOWN] ENTER I Figure 1: Gun Initialize Menu Screen (4 See Initialize [Standard] Screen. IMPORTANT: USE THE [STANDARD] SCREEN TO ADJUST GUN SIGHT DURING NEW INSTALLATIONS OR AFTER SERVICING GUN.
Operator’s Manual , (4. / GUN INlTlALlZE [STANDARD] b , SHOOT AT SCREEN TO CHECK GUN ACCURACY STEP ON PEDAL: PUSH SERVICE SW: 4 ADJUST GUN-SIGHT EXIT GUN-SIGHT CALIBRATION SCREEN y X NJ AIM AT CENTER OF THE CROSS AND PULL GUN TRIGGER Figure 2: Gun Initialize [Standard] Screen (a) If properly initialized, when the gun is fired, the Green Target should register in the entire area outlined in white. (b) Return to the initialization screen. Check gun response, in (a) above.
namco Operator’s Manual TUT QlU5USTM COIN OPTIONS GAME OPTIONS l/O TEST MONITOR TEST SOUND TEST ADS DATA OTHERS GUN INIT: SERVICE SW + TEST SW [ONj SHOOT INSIDE SCREEN: CHOOSE [up] SHOOT OUTSIDE: CHOOSE [DOWN] STEP ON PEDAL: ENTER Figure 3: Menu Screen COIN OPTIONS [DEFAULT IN GREEN] - GAME COST - CONTINUE COST FREE PLAY DEFAULT 3 COINS 1 CREDIT 3 COINS 1 CREDIT OFF EXIT SHOOT INSIDE SCREEN: CHOOSE [UP] SHOOT OUTSIDE SCREEN: CHOOSE [DOWNI STEP ON PEDAL: ENTER Figure 4: Coin Options Screen OFF 5
name= TW=lE Operator’s Manual W%OSTM 50 INCH GAME OPTIONS [DEFAULT IN GREEN] (a) (W w (4 - w- - PLAYER’S LIFE TIME LIMIT HIT EFFECT SOUND IN ATTRACT - DEFAULT 3 SHORT RED ON 3 MED RED ON RECORD TIME CLEAR NO EXIT SHOOT INSIDE SCREEN: CHOOSE [UP] SHOOT OUTSIDE SCREEN: CHOOSE [DOWN] STEP ON PEDAL: ENTER Figure 5: Game Options Screen ITEM (a) Player’s Life (b) Time Limit (c) Hit Effect (d) Sound in Attract (e) Record Time Clear AVAILABLE SETTINGS I-9 Very Short, Short, Medium, Long, Very Long
name0 Operator’s Manual UURi@ CIXOSOSTM l/O TEST -DIPSW4 NOTES (4 ON w - 12345676 [ON/OFF] SWlTCH TEST - SOLENOID TEST EXIT SHOOT INSIDE SCREEN: CHOOSE [UP] SHOOT OUTSIDE SCREEN: CHOOSE fDOW?Jj STEPDNPEDAL: ENTER Figure 6: l/O Test Screen Notes: (a) See Switch Test Screen. (b) See Solenoid Test Screen. (c) Returns You to Main Menu.
nameoUWUR CAUdOJTM 50 INCH Operator’s Manual \ / SWITCH TEST [DEFAULT IN GREEN] DIPSW4 12345678 DEFAULT [ON/OFF] SW l-8 OFF SWlTCH (a) W 3 COIN: SERVICE: TEST: GUN TRIGGER: FOOT PEDAL: OFF OFF ON OFF ON OFF OFF OFF OFF OFF SERVICE SW + PEDAL: EXIT J L Figure 7: f&itch Test Screen Notes: (a) ON or OFF ini response to switch activation. (b) Foot Pedal Switch registers OFF when the pedal is pressed [when foot is on the pedal].
Operator’s Manual / MONITOR TEST !iQIEi GRADATION PATTERN CROSSHATCH PATTERN [CRTI CROSSHATCH PATTERN [PROJECTOR] It; (a b (d) w .
namco7r’Wi ~ $AIJISTM 50 INCH (a) Gradation Pattern (b) Crosshatch Pattern [CRT] (c) Crosshatch Pattern [Projector] (d) White Window P-L M. Ll (e) Interlace Pattern (f) View Angle Adjust [CRT] (g) View Angle Adjust [Projector] (h) Full White * Note: ODerator’s Manual Monitor Test Descriptions Four bars (G, R, B, W from top to bottom) with 15 gradations each are displayed. Green Grid is displayed. Lines should be reasonably straight, undistorted and uniformly bright across screen.
Operator’s Manual SOUND TEST [DEFAULT IN GREEN] MESSAGE: CIUATTRO lb) VER5.2 VOLUME FRONT L SP 50 [MAX631 FRONT R SP 50 [MAX631 REQUEST SONG NO.
namco’ Operator’s Manual TODK WSUSTM 50 INCH ADS DATA TOTAL COINS START COINS CONTINUE COINS TOTAL CREDITS 0 [ csvc 0000 ] 0 [ csvc 0000 ] 0 [ +svc 0000 ] 0 ON TIME PLP‘Y TIME TOTAL BLOW BACKS STEPS ON PEDAL 0:00’00” 0:00’0D” 0000 0000 STORY GAMES [CONTINUES T.A. VIMEO] GAMES - (a)(b)- 000 0001 0 STORY START/END STORY GAME OVERS T.A.
name0 Operator’s Manual IMilE WXP’ 50 INCH OTHERS NOTES ROM VER. 96101108 18:57:09 EEP-ROM INITIALIZE PCS TEST EXIT SHOOT INSIDE SCREEN: SHOOT OUTSIDE SCREEN: STEP ON PEDA.L: CHOOSE [UP] CHOOSE [OOWN] ENTER Figure 12: Others Screen Notes: (a) Select ‘YES’ or ‘NO’ at the OK? Prompt.. If ‘YES’ is selected, be sure to recheck gun initialization. (b) Video and DSP Tests are provided for factory service personnel. (c) To EXIT, push Service Button + Pedal Switch.
nameo’ TUl=WZ CIXUBI*STM? 50 INCH 5.0 MAINTENANCE 5.1 Monitor Service Operator’s Manual The 50 inch monitor does not require regular maintenance, and there are no userserviceable parts inside. If a replacement Mitsubishi monitor i s supplied for your game, perform the Monitor Adjustment Procedure in APPENDIX A. This will ensure that it is set up for PowerOn-Restore and that the screen is properly sized and centered for your Time Crisis, game.
name0 Operator’s Manual 5.3 TUDE CROJUSTM 50 INCH Gun Removal and Disassembly section 4.1) after replacement of gun components or assemblies. 5.3.1 Opening the Gun M3XlO Cap Hd Gun Slide Gun Cover Figure 5-l Opening the Gun I. Remove the four M3 x 10 cap screws and one M4 x 25 button head screw that attach the gun side halves. 2. Remove the gun side halves. 3.
nameo’ UWiE fJXUSUSTM 50 INCH Operator’s Manual 5.3.2 Replacing the Gun Solenoid I, Remove the gun covers and gun side halves. M4 X 6 Cap Screw ? Slide t Solenoid Bracket Ground Wire Lock Washer hi3 X 8 Cap Screw Figure 5-2 Gun Solenoid Assembly 2. Disconnect the solenoid connector. 3. Remove the M3 x IO cap screw attaching the solenoid/slide assembly to the left gun cover. 4. Remove the M3 x 8 cap screw and washer attaching the ground wire to the solenoid bracket. 5. Loosen the solenoid nut.
Cberator’s namecr UUVilE CR030~TM Manual Figure 5-3 50 INCH Solenoid Plunger Detail 9. When reassembling the solenoid, pay particular attention to the order of E-rings and spacers. Make sure the solenoid harness faces downward upon reassembly. Figure 5-4 Solenoid Reassembly 5.3.3 Trigger Switch Replacement 1. Remove the gun covers and gun side halves. 2. Remove the two screws that attach the microswitch to its bracket. 3.
namco-WE CJXOSUSTM Operator’s Manual 50 INCH 6.0 TROUBLESHOOTING Solution Probable Cause Problem 10 AC power. lo video or sound. T= Check main AC fuse i n rear of cabinet. If fuse is OK, check voltage ~~mcc YVlV”” Vo DC power. \lo video, but nonitor is poweredJP. 1) 2) 2) Jideo input to monitor is disconnected, or bad video cable. 1) Monitor problem. 2) innnIt cirla F M I fi!tp~, .ShnU!d aany”. “,“” nf “, -.... be 115-12OVAC. If no voltage, then ON/OFF switch is bad, replace.
ODerator’s name0 Manual TWX WSOSTM 50 INCH Troubleshooting (continued) connected on SS22 P Verify that RGB and SYNC signals are present at J9 pins 1.2,3,4 w.r.t. pin 5. N O T E : D O N O T ATEMPT T O REPAIR PCBs OR WARRANTY WILL BE VOIDED. If main PCB rack is PCB (mounted on top of main PCB rack). Check continuity of cables from J2 to RCA jacks on back of monitor.
name=0 UURlE CWSTM Problem 50 INCH Operator’s Manual Troubleshooting (continued) Probable Cause or is out of adjustment.
ODerator’s Manual NOTES ON 50 INCH MONITOR (HITACHI) 1. Alianment Upon initial installation, or after the game has been moved, the following alignment procedure should be performed. a. Remove the cover plate located in the lower center of the monitor cover, providing access to the monitor service panel. Locate the remote control unit. INPUT 3 I I I S-VliDEO Hitachi 2. Front Service AlJ’OIO Panel b. On the service panel press the Magic Focus button.
name= TUflE ‘WsSUSTM 50 INCH APPENDIX A: MONITOR ADJUSTMENT PROCEDURE (Mitsubishi VS-5041!42) Operator’s Manual
WITH MITSUBISHI MODEL 5041 OR 5042 CAIl77ON: The TV power plug will fit into the the power outlet only one way. DO NOT force the power plug into the power strip. 1. Make sure the TV is OFF. 2. Plug the Test Fixture S-VI-IS Cable to the DIN adapter of the TV front panel. 3. Using the remote control turn the TV ON. Let the TV warm up for a few minutes (3-5 minutes). 4. Press the (? $ ) INPUT buttons to change to SYNC - 3 (S-VIDEO) on the TV screen. 5.
* Select “First Time Set Up” using the ADJUST (? 4 ) buttons and press ENTER button. l You will see the “First Time Set-Up” screen. Select the “Align Colors” using the ADJUST (?+ d) bu tt ons; then press the Enter button. You will see “Align Colors” screen. Press “VIDEO” for the first time. You will see %VHITE” crosshairs on the screen with t RED + on top of the crosshairs.
7. Power Restore Adjustment; Press the “MENU” button to get into the “TV l Main Menu”. Select “Customize Viewing”, use “ADJUST l (? -1) buttons. Press Enter button. Select “Use Power Restore” using the l ADJUST (? &) buttons; then press Enter button. The “Use Power Restore” screen will appear. Use ADJUST buttons to select “ON” and press Enter and then it will automatically return back to the “Customize Viewing” menu. Press “Menu” button to return to the “TV Main Menu”.
8. DJent Mode: a. Press the “MENU” button on the remote control (the TV Main Menu will appear). b. Press the button “2”, “3”, ‘Y’, “7” in that order. (The screen will change to the circuit adjustment mode). If it is not changed, repeat step a and b again. c. After these numbers are entered, a text screen and numbers will appear in the middle of left-handed screen. d. Press “VIDEO” button to advance to #lo, Vertical Height (VHT). e. Press ADJUST (? &) arrow to change the adjustment value to “ 50 “. f.
NOTE: These “initial data” are the initial values of that adjustment These initial data may not be correct for the normal performance of each TV monitor. The visual check is necessary.
Operator’s Manual APPENDIX B: PARTS LIST and ILLUSTRATIONS I Major Assemblies (Front View) Page Major Assembiies (Rear Viewj B-3 $5 Monitor Cabinet Assembly (Front View) Monitor Cabinet Assembly, (Rear View) B-6 B-7 Monitor B-8 Cabinet Assembly parts list Monitor Cabinet Assembly parts list (con?) Control Panel, Blue Gun & Tether Assemblies B-9 B-10 Pedal Assembly w/Harness B-l 1 PCB Set Assembly B-12 List of Harness Assemblies Power Plate (AC) Assembly Service Panel Assembly Blue Gun As
TIME CRISIS 50” MONITOR, Major Assemblies (Front View) - Monitor Assembly Monitor Cabinet Assembly ” ,- ‘.. Gun _.
TIME CRISIS 50” MONITOR, Major Assemblies (Rear View) Monitor _ . ~ Power FiY ’ jl :upp/y \ 8-5 Assembly Power suppty Assembly ,^,, ,I_. .-.._I Access NTSC PCB Gun Drive PC8 U.L.
TIME CRISIS 50” MONITOR, Cabinet Assembly (Front View) TCOI-04709-00
TIME CRISIS 50” MONITOR, Cabinet Assembly, (Rear View) TCOi-O4709-00
TIME CRISIS 50” MONITOR, Cabinet Assembly - nwwog-oo 1 TCO5-04786-00 MONITOR C A B I N E T ASSEMBLY 3 VGlC-04741-W Grill. Ptiorat~ lB&m 01 Mmlor CaL~rrt US s'WI?.S) 1 46 VGZO-02865-05 Washer, Flat. #iO.Black.Dxlde 2 47 TClO-04909-00 Plate. Access,&gic 11 Focus B u t t o n (HIT 2281 1 Focus Button(HIT23K) 1 4 TC40-04MO-00 ___.. 5 VG24-04933-00 DeGl. me Panel 2 47a TClO-05108-00 Plaa. Access. Cask:, 8 48 VGZO-02888-04 silew VG20-028M.12 6 Scr:w.Hex-Hd.1/4-20 32 49 TC40.
TIME CRISIS 50” MONITOR, Cabinet Assembly (Continued) TCOl-04709-00 - 88 VG78-00476-00 Filter, EMI, 35 VG2&02903-l? Screw, Pan-Hd ,Wood. 89 TCW04733-00 Harness, 90 VGlO-03811-00 Brackel,Ground 91 35 VG20-02700-05 Nut. Kep. RlO-24. VGZO-02903-Q Screw,Pan-Hd..Wooa, 92 VGZO-03579-00 Slandoff 93 VG84-m792-00 PCS, NTSC 94 TC50-04727-0a Hamess.RGBto 95 TCO3-04886-00 P C S , G u n Drive 56 TC50-04729-00 Harness, Gun Dr~veto 9' 98 X50-04728-00 VG15-04947-00 Hamess.
TIME CRISIS 50” MONITOR, Control Panel, Blue Gun 81 Tether Assemblies TC90-04738-01, 1 TC90-04738-01 Control Panelw/Speaker 2 VG2&02889-16 Screw.Etn-Hd..Tmp-Prf.#lO-24x1', 3 VGZO-02865-05 Washer. Flat. 110, 4 TC4h7463P00 5 PBO3-03141-01 & TCO50471500 Holes (plastic) 1 17 VGZO-02865-05 Washer,Flat,tiO. Black.Ox$de 9 16 TC05-04715-00 TETHER 9 19 PB20-03154-00 Cham. cml. Panel. instrKlm 1 20 PEtlO-03153-00 CIIP CY54-03866-00 Speaker,4 Ohm.20W.4'Sq. 2 VGZO-02903-10 Screw.
TIME CRISIS 50” MONITOR, Pedal Assembly w/Harness - Pedal Assembly, Side View 1 96-0145-00 - TCIO-04716.00 Btackel. 2 TC40-04666-00 Decal, feda/ 3 VGZO-0288S20 ScrewBtn-Hd..Tm~~d.#10-24x1-1/~ 4 VGZO-049X-16 5 VGZO-02863-05 R TC%04730-00 Hamess.Gun 7 8 96-0149-00 43~0127-00 9 43-1013-00 1 0 43-0175-00 11 12 43-0324-00 96-0134-00 ' 3 43-0425-00 14 96-0153-00 15 96m0:40-CO I" 4%Oi75-00 1 6 43-3066-00 Foal Pedal /nslruclfon X10, Black, Oxide & P edal Exlenston, Hamess.
TIME CRISIS 50” MONITOR, PCB Set Assembly TCOS-04786-00 WARNING: DO NOT separate board set. 1 CYO6-03939M Card cage 1 14 A203-04571-W Mother PC6 Assembly (8646960602) 2 3 V620-02896-36 VGZO-02862.04 Screw Pan-Hd,Ph~lipr,18-32x2-1/~.SI1.Zn Washer. Split-Lock. 18. SW Zinc 4 4 15 16 TC03-04845-W TC03-04847-W CPU(6)PCEAssembly(BM69626OO~ 4 VGZO-02864~4 4 17 TCO%l3849-W 5 cY06-03910ul Washer, Flat ia.
TIME CRISIS 50” MONITOR, List of Harness Assemblies 1 PHI SUPPlY -~ .-~ +'8hws. SJT.6Ft.w/Moldd Plug 1 2 cw-03998.00 Harness. POW CGrd.Alqht 3 ~251 owe-a0 PoverCoid.3Cand. 4 Tc50.0472oda Harness 13 HarneSs TCM-04914-aa 1 spearer. 50' hmlfOl 1 Fltolescenl - -. 16 EJ-a4124da Hainess. DC Pow31 5o'Monltor 1 17 18 Tc50~041350a Tc5sou32iIa H61"W 1 19 Tcw-04725-00 Harness. CO," oooi B seruce PM 5c Monitor 20 m&04126-00 21 CY5uO371 Harnesr.Co"Ooor~ens,o" Har"ess.
TIME CRISIS, 50” MONITOR, Blue Gun Assembly PEO3-03141-01 ?iQ 1. 7 3. 4. 2. PB900U136al 6. PB10-@4669ao 7. PB10-04.57MO 3. PBOY-29Wl 9. PBOY-29&20 -L TRlGGER.
name0 UUnE ‘CRUBUSTM c c APPENDIX C: 50 INCH WIRING DIAGRAM Operator’s Manual
-~ WVU9Vla 3NltllM Lo-z68Po-oS31 96/62/L axva 9 :mtl llVkUA0 ,,05 SlSlkl3 3Wll --____- I E3d olanv II
