VS-50803 VS-60803 WS-65903 VS-70803 WS-73903 VS-80803 AV Systems Connections Guide VIDEO S-VIDEO AUDIO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 G B H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr Cb DVD VIDEO IR HOME THEATER ACTIVE A/V IR/ G LINK NETWORK V L (MONO) R L (MONO) R ANT-A LOOP OUT VIDEO PIP AUDIO OUTPUT AUDIO ANT-B 1
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
MITSUBISHI Connections Table of Contents Chapter 1: Basic Connections ............................................ 5 TV + separate UHF and VHF antennas ................................... 6 TV + antenna or cable without a cable box .............................. 8 TV + cable with a cable box when TV Guide Plus + will not be used ........................................................................ 10 TV + VCR + cable with a cable box when TV Guide Plus + will not be used ..............................
blank page AV Systems Connection Guide 4
CHAPTER ONE Basic Connections This section will show you the basic connections to hookup your TV. If you have difficulty making any of the connections to your TV, you may want to contact your Mitsubishi dealer or your local cable company.
TV + separate UHF and VHF antennas VHF Antenna (Channels 2-13) Flat Twin Lead UHF Antenna (Channels 14-69) Flat Twin Lead TV Rear Terminal External Antenna or Cable VIDEO S-VIDEO AUDIO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 G B H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y 300 Ohm to 75 Ohm Combiner UHF Cr DVD VIDEO ¢ ANT-A LOOP OUT VHF Side AV Systems Connection Guide 6 IR HOME THEATER ACTIVE A/V IR/ G LINK NETWORK V L (MONO)
TV + separate UHF and VHF antennas If UHF and VHF signals are brought into your home with two separate antennas, you’ll need to combine them in order to connect them to the TV. To do this you will need a UHF/VHF combiner. Use this hook-up to: • connect separate UHF and VHF antennas to your TV.
TV + antenna or cable without a cable box TV rear terminals VIDEO S-VIDEO AUDIO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 75 Ohm Coaxial Cable G B H V INPUT-2 HDTV CONTROL 300 Ohm Flat Twin Lead HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr Cb DVD VIDEO IR HOME THEATER ACTIVE A/V IR/ G LINK NETWORK V L (MONO) R L (MONO) R † ¢ ANT-A LOOP OUT Optional 300 Ohm to 75 Ohm Matching Transformer AV Systems Connection Guide 8 VIDEO ANT-B AUDIO PIP AUDIO OUTPU
TV + antenna or cable without a cable box Use this hook-up to: • connect the incoming cable or antenna to the ANT-A input terminal on the TV. equipment you will need: If you have a standard 75-ohm coaxial cable, you will not need additional equipment. If your antenna has two leads (called twin lead or 300 ohm antenna lead), you will need: 300 ohm - in 75 ohm - out One 300-75 ohm matching transformer procedure: † Use a screwdriver to connect the 300 ohm twin leads to the transformer.
TV + cable with a cable box when TV GUIDE Plus + will not be used TV rear terminals VIDEO S-VIDEO AUDIO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 G B H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr IR HOME THEATER Cb DVD VIDEO Incoming Cable † £ IN ANT-A LOOP OUT VIDEO ANT-B £ Cable Box rear terminals OUT AV Systems Connection Guide 10 V L (MONO) R L (MONO) R ¢ ¢ ACTIVE A/V IR/ G LINK NETWORK AUDIO PIP AUDIO OUTPUT
TV + cable with a cable box when TV GUIDE Plus + will not be used This hook-up will allow you to use the advanced features of your TV, such as 2-tuner PIP and SuperQuickView™ and watch basic cable channels on Antenna-A. You will be able to view the premium cable channels that are descrambled by your cable box on Antenna-B.
TV + VCR + cable with a cable box when TV GUIDE Plus + will not be used VCR Rear Terminals Yellow £ L Antenna § ® L (Y/C) CH-1 CH-1 2 1 Red VIDEO OUT AUDIO IN AUDIO OUT White IN © 1 MONITOR R R CH-2 CH-2 OUT Attach only one cable type W h i t e R e d Yellow § © TV Rear Terminals VIDEO AUDIO S-VIDEO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 G B H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr IR HOME THEATER Cb D
TV + VCR + cable with a cable box when TV GUIDE Plus + will not be used Use this hook-up to: • connect a VCR along with your cable and cable box, when you will not be using TV GUIDE Plus+ equipment you will need: R R LL L L R R Three lengths of 75 ohm coaxial cable One set of RCA pintype audio cables One RCA pin-type video cable (if connecting a standard VCR) One S-Video cable (if connecting a S-VHS VCR) procedure: † Connect the incoming cable to the ANT-A terminal on back of the TV.
TV + VCR + antenna or cable without a cable box VCR Rear Terminals Yellow ¢ IN White L L CH-1 Antenna CH-1 2 1 Red £ VIDEO OUT AUDIO IN AUDIO OUT © (Y/C) ® 1 MONITOR R R CH-2 CH-2 OUT Attach only one cable type W h i t e ® R e d © Yellow TV Rear Terminals VIDEO S-VIDEO AUDIO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 G B H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr Cb DVD VIDEO IR HOME THEATER ACTIVE A/V IR/ G LI
TV + VCR + antenna or cable without a cable box Use this hook-up to: • connect a VCR along with your cable or antenna equipment you will need: R L L R Two lengths of 75 ohm coaxial cable One set of RCA pin-type audio cable One IR emitter assembly (if connecting TV Guide Plus + One RCA pin- OR One S-Video cable type video (if connecting cable a S-VHS VCR) procedure † Connect the incoming cable to the ANT-A terminal on back of the TV.
Connecting the Infrared (IR) Emitter for TV GUIDE Plus+ TV Back Panel VIDEO S-VIDEO AUDIO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 G B H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr Cb DVD VIDEO IR HOME THEATER IR/ G LINK ACTIVE A/V NETWORK V L (MONO) R L (MONO) R ANT-A LOOP OUT VIDEO PIP AUDIO OUTPUT AUDIO ANT-B IR Emitter Connector Cable Box VCR Channel Choice IR Emitter Set Up Adhesive Foam Tape* IR Cable + VCR + Cable Bo
Connecting the Infrared (IR) Emitter for TV GUIDE Plus+ Use this hook-up to: • use TV GUIDE Plus+ with a cable box and/or VCR. There are two separate IR emitters connected to the end of the plug. Each IR emitter is used to send control signals from your TV to your cable box, and/or your VCR. equipment you will need (included with TV): Transmitter Lenses IR Emitter IR emitter assembly two strips of double-sided adhesive foam tape (not pictured).
TV + cable with a cable box when TV GUIDE Plus + will be used Incoming Cable † TV Rear Terminal VIDEO AUDIO HIGH-DEFINITION INTERFACE IN S-VIDEO OUT V L (MONO) R HDTV VIDEO OUT R INPUT-1 G B H V INPUT-2 HDTV CONTROL £ ¢ HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr Cb DVD VIDEO IR HOME THEATER ACTIVE A/V IR/ G LINK NETWORK V L (MONO) R L (MONO) R ANT-A LOOP OUT VIDEO ANT-B © ® IR Emitter ¢ £ ® Cable Box Rear Terminal IN OUT AV Systems Connection Guide 18 AUDIO P
TV + cable with a cable box when TV GUIDE Plus + will be used Use this hook-up to: • connect a cable box to view premium cable channels and use TV GUIDE Plus+ equipment you will need: IN OUT Transmitter Lenses OUT IR Emitter one two-way splitter four lengths of 75 ohm coaxial cable one IR emitter assembly (provided with TV) procedure: † Connect the cable system’s incoming cable to the IN terminal on the two-way splitter. NOTE: This splitter must be a type approved by your local cable provider.
TV + VCR + cable with a cable box when TV GUIDE Plus + will be used VCR Rear Terminals Yellow © L ¶ Antenna CH-1 1 Red VIDEO OUT AUDIO IN AUDIO OUT White IN L (Y/C) CH-1 2 § 1 MONITOR R R CH-2 CH-2 OUT Attach only one cable type Yellow W h i t e R e d § ¶ TV Rear Terminals VIDEO S-VIDEO AUDIO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 B G H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y © Cr IR HOME THEATER Cb DVD VIDEO
TV + VCR + cable with a cable box when TV GUIDE Plus + will be used Use this hook-up to: • connect a VCR along with a cable box and use TV GUIDE Plus+ equipment you will need: IR Transmitters IN Transmitter Lenses OUT OUT IR Emitter Connection one two-way splitter four lengths of 75 ohm coaxial cable one IR emitter (provided with TV) R L L R one set of RCA pintype audio cables One RCA pin-type video cable One S-Video cable (if connecting a S-VHS VCR) ⁄Important TV GUIDE Plus+ can control onl
TV + cable with a cable box with TV GUIDE Plus + (cont.) § Connect an RCA pin-type video cable from the VIDEO OUT terminal on the back of the VCR to the VIDEO INPUT 1 or INPUT 2 terminal on the back of the TV. ⁄Important: If you are connecting a Super VHS (S-VHS) VCR, use an S-Video cable instead of an RCA pin-type video cable. Connect this S-Video cable to the S-VIDEO OUT terminal on the VCR. Connect the other end of this cable to the S-VIDEO INPUT 1 or INPUT 2 terminal on the back of the TV.
CHAPTER TWO Additional Component Connections This book will show you the basic connections to hookup your TV with components. If you have difficulty making any of the connections to your TV, you may want to contact your Mitsubishi dealer or your local cable company.
TV + stereo audio system Audio system rear terminals CD IN White Lead AUX IN IN TAPE 1 OUT IN TAPE 2 OUT SUBWOOFER OUT (MONO) L † R Red Lead TV Rear Terminals VIDEO S-VIDEO AUDIO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 G B H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr Cb DVD VIDEO IR HOME THEATER ACTIVE A/V IR/ G LINK NETWORK V L (MONO) R L (MONO) ANT-A LOOP OUT VIDEO PIP AUDIO OUTPUT AUDIO ANT-B White Lead AV System
TV + stereo audio system After you have completed your basic connections (TV to antenna, cable, VCR and TV GUIDE Plus+ emitter assembly) as shown in the previous pages, Use this hook-up to: • listen to the sound from your TV and/or VCR through your home audio system. equipment you will need R R LL L L R R one set of RCA pin-type audio cables procedure † Connect one end of the audio cables to the AUDIO MONITOR OUTPUT terminals on the back of the TV.
TV + Mitsubishi products that have A/V network terminals Mitsubishi Component rear terminals INPUT A/V NETWORK PREOUT REAR L CENTER L IN OUT R SUB WOOFER R ¢ TV rear terminals VIDEO S-VIDEO AUDIO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 G B H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr Cb DVD VIDEO IR HOME THEATER ACTIVE A/V IR/ G LINK NETWORK V L (MONO) R L (MONO) R ANT-A LOOP OUT VIDEO ANT-B † AV Systems Connection Gu
TV + Mitsubishi products that have A/V network terminals After you have completed your basic connections (TV to antenna, cable, VCR and TV GUIDE Plus+ emitter assembly) as shown in the previous pages. When the supplied cable is connected between two Mitsubishi products with A/V network, you can point the remote control at the TV and it will “pass” the remote control command to the others. Only one of the products needs to be in “line of sight” of the remote control.
TV + DVD player with component video outputs ® VIDEO S-VIDEO AUDIO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 G H B V INPUT-2 HDTV AUDIO HDTV CONTROL L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr ACTIVE A/V IR/ G LINK NETWORK IR HOME THEATER Cb DVD VIDEO V L (MONO) R L (MONO) R ANT-A LOOP OUT VIDEO AUDIO ANT-B ¢ † £ ® DVD Rear Terminal AC-3(ANALOG OFF( PCM(ANALOG ON( AUDIO SELECTOR VIDEO OUT SELECTOR PCM/ AC-3 DIGITAL AUDIO OUT L R ANALOG VIDEO VIDEO OUT
TV + DVD player with component video outputs After you have completed the basic connections (TV to antenna, cable, VCR and TV GUIDE Plus+ emitter assembly) outlined in the previous pages, you can use the folllowing hookup to: Use this hook-up to: • view a very high resolution picture using your DVD player or other video product with component video outputs.
TV + AV receiver † VIDEO AUDIO S-VIDEO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 G B H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr IR HOME THEATER Cb DVD VIDEO V VIDEO LOOP OUT ANT-A ACTIVE A/V IR/ G LINK NETWORK L (MONO) R L R (MONO) AUDIO ANT-B ¢ £ AV Receiver AVIS WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN REC SOURCE LINE OUT RISQUE DE CHOC ELECTRIQUE NE PAS ENLEVER LISTED 857C ANTENNA UL PRE OUT SUR.
TV + AV receiver After you have completed your basic connections (TV to antenna, cable, VCR and TV GUIDE Plus+ transmitter) as shown in the previous pages, use this hook-up to: • Select the inputs and control the sound through the AV receiver's remote control. Your TV will act as a monitor, showing the video selected by the AV receiver. After installation you MUST select the correct AV Connection Menu choices. See Chapter 2, "Creating the AV Connection.
Connecting the Infrared (IR) Emitter for the Home Theater connection TV Back Panel VIDEO S-VIDEO AUDIO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 G B H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr Cb DVD VIDEO IR HOME THEATER ACTIVE A/V IR/ G LINK NETWORK V L (MONO) R L (MONO) R ANT-A LOOP OUT VIDEO AUDIO ANT-B AV Receiver IR Cable + AV Receiver AV Systems Connection Guide 32 PIP AUDIO OUTPUT
Connecting the Infrared (IR) Emitter for the Home Theater connection Use this hook-up to: • connect a Mitsubishi AV receiver to your TV for the Home Theater function. equipment you will need (included with TV): Transmitter Lenses IR Emitter IR emitter assembly two strips of double-sided adhesive foam tape (not pictured). Included with your television is an IR emitter assembly. There are two separate IR transmitter lenses connected to the end of the plug.
TV + HDTV Receiver ® VIDEO AUDIO S-VIDEO V HIGH-DEFINITION INTERFACE L (MONO) R HDTV VIDEO R INPUT-1 B G H V INPUT-2 HDTV CONTROL HDTV AUDIO L (MONO) R INPUT-3 MONITOR OUTPUT Y Cr IR HOME THEATER Cb DVD VIDEO ACTIVE A/V IR/ G LINK NETWORK V ¢ From the Cable or Cable Box LOOP OUT ANT-A L (MONO) R L (MONO) R VIDEO PIP AUDIO OUTPUT AUDIO ANT-B £ From the Antenna £ To Digital Audio Receiver ¢ THIS PRODUCT CONTAINS ONE OR MORE PROGRAMS PROTECTED UNDER INTERNATIONAL AND U.
TV + HDTV Receiver (cont.) use this hook-up to: • connect your Mitsubishi HDTV receiver and a cable television system. equipment you will need: R R LL L L R R one length of HDTV control cable one 5-in-1 BNC pintype video cable one set of RCA pintype audio cables one length of coaxial cable procedure † Connect the cable from the outside antenna to the ANT-IN input terminal on the Mitsubishi HDTV receiver. Connect the cable system coaxial cable to the ANT A terminal on your television.
MITSUBISHI CONSUMER ELECTRONICS AMERICA, INC. 9351 Jeronimo Road Irvine, CA 92618-1904 800-332-2119 © 1998 Mitsubishi Consumer Electronics America, Inc. 871C570A10 AV Systems Connection Guide 36 Printed in U.S.