WD-62827 WD-62927 WD-73827 WD-73927 Projection Television Owner’s Guide TV Information Use this space to record the model number and serial number of your television. This information is on the back of your TV. Model Number Serial Number Purchase Date TM 5. visit our website at www.mitsubishi-tv.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude to constitute a risk of electric shock.
FCC Declaration of Conformity Product: Projection Television Receiver Models: WD-62827, WD-62927, WD-73827, WD-73927 Responsible Party: Mitsubishi Digital Electronics America, Inc. 9351 Jeronimo Road Irvine, CA 92618-1904 Telephone: 949-465-6000 This device complies with Part 15 of the FCC Rules.
IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference. Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference. Follow all operating and use instructions. 2. Heed Warnings Adhere to all warnings on the appliance and in the operating instructions. 3.
IMPORTANT SAFEGUARDS, continued 12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 13.
Contents Chapter 1: Television Overview TV Accessories.. . . . . . . . . . . . Special Features of Your TV.. Memory Card Reader. . . . . . . Front Control Panel. . . . . . . . . Remote Control.. . . . . . . . . . . . TV Back Panel.. . . . . . . . . . . . . System Reset Button.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 5: TV Menu Operations Main Menu.. . . . . . . . . . . . Setup Menu . . . . . . . . . . . NetCommand® Menu . . Record Menu. . . . . . . . . . Channel Menu . . . . . . . . . Captions Menu. . . . . . . . . V-Chip Lock Menu. . . . . . Audio/Video Menu. . . . . . Audio Settings.. . . . . . . . . Video Settings.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Our Thanks... Thank you for choosing Mitsubishi as your premier Home Entertainment provider This Owner’s Guide describes the features and functions of your Mitsubishi widescreen, high definition TV. We urge you to examine this Owner’s Guide to become familiar with the innovative features and operations this unique television offers. The very core of our corporate philosophy is to provide our customers with the very best.
Chapter 1 Television Overview TV Accessories. . . . . . . . . . Special Features of Your TV.. Memory Card Reader. . . . . . Front Control Panel. . . . . . . Remote Control. . . . . . . . . . TV Back Panel. . . . . . . . . . . System Reset Button. . . . . . TV Reset Menu.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TV Accessories Please take a moment to review the following list of items to ensure that you have received everything. 4. $"#-& %#4 %57 7$3 %7% "6%*0 57 427 27 $) 70- One two-headed IR emitter cable (allows NetCommand to control other devices) 108&3 46# $"/$&- %&7*$& .65& 1"(& 5. One four-headed IR emitter cable (allows NetCommand to control other devices) (6*%& 57 .&/6 %&7*$& .&/6 )0.
Special Features of Your TV Your new high-definition widescreen television has many special features that make it the perfect center of your home entertainment system, including: High Definition DLP™ Display System Your widescreen Mitsubishi HDTV uses Texas Instruments most advanced Digital Light Processing™ technology for rear-projection televisions.
16:9 Widescreen Picture Format Enjoy a full theatrical experience in the comfort of your home. View pictures as film directors intended them. Digital TV broadcasts, DVDs and newer video game consoles support this widescreen format. Memory Card Reader You can display a slide show of your favorite JPEG pictures or listen to MP3 or WMA audio selections that have been recorded on compatible memory cards.
Memory Card Reader and Front-Panel Inputs Memory Card Reader Figure 1 The memory card reader has four card slots that accept a variety of popular memory card types. The reader lets you view JPEG pictures from many digital cameras and allows you to listen to MP3 or WMA audio files recorded from computers or other digital recording devices. The card slots are designed for the specific types of cards listed below. Other cards or objects should not be inserted into the slots as this may damage the TV.
Front Control Panel The shaded buttons on the front control panel are duplicated on the remote control. The top row of labels shows the control functions when there are no TV menus displayed on the screen. The bottom row of labels shows the control functions when the TV menus are displayed on the screen or when a special function has been activated. See “Remote Control Overview” for further details on the functions of these buttons. 1 3 4 1 5 Front Control Panel 1.
Front Control Panel, continued Status Indicator Indicator Color TV Condition Additional Information None (indicator off) Normal TV on or standby condition. Normal operation. Yellow, steady Room temperature is too high. TV will not operate when the ambient room temperature is too high. Turn off the TV and wait until the room temperature drops. Red, either steady or TV may require service. blinking Turn off the TV and unplug the set from the AC power source.
Remote Control Overview Figure 1, next page 1. 2. 3. 4. 5. 6. Slide Switch: Selects the A/V product to be controlled by the remote control. Select TV for NetCommand® device control. Numbers: Individually select channels or enter information into menus. SQV (SuperQuickView™): Scans through memorized lists of favorite channels. CH(ANNEL)/PAGE: Scans up or down through memorized channels.
Remote Control, continued 1 2 3 4 5 6 7 8 9 10 11 12 18 108&3 46# $"/$&- 427 %&7*$& 27 $) 70- Figure 2. Operation: Installing the Batteries .65& 1"(& (6*%& 57 .&/6 23 24 %&7*$& .&/6 )0.& 7 $)*1 */'0 1*1 101 1*1 $) "" BMLBMJOF CBUUFSJFT 20 22 13 15 19 21 1*1 %&7*$& 14 17 $"#-& %#4 %57 7$3 %7% "6%*0 57 2. Load the batteries, making sure the polarities (+) and (-) are correct. For best results, insert the negative (-) side first.
TV Back Panel Note: 15-pin D-subminiature PC input (item 6) offered on models WD-62927 and WD-73927 only. 4 */165 3 6 1$ */165 )[ 7(" 8 7(" 47(" 8 47(" 9(" 8 9(" 9 9 $0.10/&/5 :1C1S J Q Q J 2 : 5 */165 065165 %7* "OBMPH "VEJP 4 7*%&0 1C 7*%&0 1S "6%*0 -&'5 .0/0 "6%*0 -&'5 .0/0 "6%*0 3*()5 "6%*0 3*()5 "6%*0 065165 ( -JOL¸ 7 7*%&0 AUDIOLEFT/ (MONO) "6%*0 3*()5 .0/*503-*/, )%.* 7*%&0 J Q Q J "6%*0 1$.
TV Back Panel, continued 5. DVI Analog Audio Unlike HDMI, DVI does not carry audio information on the same cable. Use these analog stereo audio inputs when using the HDMI input with a device that outputs DVI instead of HDMI, such as DVI output from a DVD player. 6. PC Input (models WD-62927, WD-73927 only) (VGA/W-VGA/SVGA/W-SVGA/XGA/W-XGA/1280 x 720, 1920 x 1080, 60 Hz) This input can be used to connect a personal computer. Please see Appendix A for signal compatibility.
Additional Information Using the Reset Menu for Reset of the TV or TV Disc System Reset Button If the TV doesn’t respond to either the remote control or the front panel controls or will not power off, press the SYSTEM RESET button on the front panel with a pointed item such as the point of a ball point pen or end tip of a paperclip. Select any device from the Device Selection menu, except for TV Disc. Press TV MENU followed by 1,2,3 to see the RESET SERVICE MENU to reset the TV or TV Disc.
Chapter 2 Connecting External Devices and NetCommand® Setup. . . . . . . . . . . . . . Wall Outlet Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Standard Cable Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Antenna with a Single Lead. . . . . . . . . . . . . . . . . . . . . . . . . . Antennas with Separate UHF and VHF Leads. . . . . . . . . . . . . VCR to an Antenna or Wall Outlet Cable (Audio & Video).. . . . . VCR to a Cable Box (Audio & Video). . . .
Connecting External Devices and NetCommand® Setup NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to each device through IR emitters. Additionally, it is also able to learn the remote control signals used by most audio video devices not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or learned Audio/Video (A/V) Receivers to the correct input used with each device.
Connecting a Wall Outlet Cable or Cable Box Wall Outlet Cable Standard Cable Box (can be used with a CableCARD™) (cable box, other than an HDTV cable box; this setup allows two-channel PIP) Figure 2 3 coaxial cables and one two-way RF splitter are required. These are not included with the TV. Figure 1 It is very important to connect the incoming cable for your primary viewing source to ANT-1, especially for CableCARD™ use and to download TV Guide On $0.10/&/5 */165 Screen® listings.
Connecting an Antenna with a Single Lead or Antennas with Separate UHF and VHF Leads Antenna with a Single Lead (not for use with CableCARD™) Figure 3 */165 */165 065165 Figure 4 %7* A UHF/VHF combiner is required. This is not included with the "OBMPH "VEJP 1CTV, but is available at most electronics stores. : For antennas with flat twin leads "6%*0 065165 4 7*%&0 A 300-ohm-to-75-ohm transformer is required. This is not included with the TV, but is available at most electronics stores.
Connecting a VCR to an Antenna or Wall Outlet Cable Connecting VCR Audio and Video to the TV VCR to an Antenna or Wall Outlet Cable (Audio & Video) 5. Connect either an S-Video or Video cable from VIDEO OUT on the VCR back panel to INPUT-1 VIDEO on the TV back panel. Only one type of video cable should be connected. S-Video is recommended, if available. Figure 5 A two-way RF splitter, 3 coaxial cables, right and left audio cables, and an S-video or video cable are required.
Connecting a VCR to a Cable Box (Audio & Video) VCR to a Cable Box (Audio & Video) connects to the L (left) channel. If your VCR is mono (non-stereo), connect only the white (left) cable. Figure 6 A two-way RF splitter, 4 coaxial cables, right and left audio cables and an S-Video or Video cable are required. These are not included with the TV but are available at most electronics stores. 1. 7. Connect the incoming cable to IN on the RF splitter. 8.
Connecting an A/V Receiver (Stereo System) Connecting a Satellite Receiver or Other Device with S -Video A/V Receiver (Stereo System) Figure 7 Most setups require either a digital audio cable or stereo audio cables. In some circumstances, you may need to connect both digital audio and stereo audio. A digital audio cable is provided with the TV. Stereo audio cables are not included.
Connecting a DVD Player with Component Video Connecting a DVI Device DVI Device DVD Player with Component Video Figure 10 A DVI-to-HDMI cable or DVI/HDMI adaptor and HDMI cable and audio cables are required. These are not included with the TV. They may be available at your local electronics retailer. Figure 9 Component video cables and audio cables are required. These are not included with the TV. 1.
Connecting an HDTV Cable Box or Satellite Receiver with Component Video Connecting an HDMI Device HDTV Cable Box or Satellite Receiver with Component Video HDTV Receiver to TV Back panel • Y to Y • Pr to Pr • Pb to Pb 4. Connect L (left) and R (right) audio cables from the DTV receiver to Component-1 AUDIO on the TV back panel. 5. If you are using a satellite receiver, you must change the input through NetCommand. Open the NetCommand Connection for [Device] screen (see page 48) to make the change.
Connecting a MonitorLink™ Control/RS-232C Device MonitorLink Control/RS-232C Device Figure 13 A 9-pin RS-232C cable is required. This is not included with the TV. It may be available at your local electronics retailer When used as an RS-232C port, you can connect to other external controllers. See mitsubish-tv.com for RS-232C command protocols. Connect a 9-pin RS-232C cable from the TV back panel to the MonitorLink or RS-232C jack on the external control device.
Connecting the IR Emitter NetCommand® $0.10/&/5 */165 IR Emitter NetCommand® "6%*0 -&'5 .0/0 "6%*0 3*()5 0UIFS " 7 EFWJDF ( -JOL¸ *3 &.*55&3 /FU $PNNBOE¸ The NetCommand system uses emitters connected to these jacks to control other devices such as VCRs, DVD players, cable boxes and satellite receivers. Connect the plug end of the supplied IR emitter cable to either of the IR Emitter NetCommand jacks on the TV back panel.
Connecting Compatible IEEE 1394 Devices, continued Connection Styles There are two different connection styles that can be used when connecting IEEE 1394 devices. Use the style that fits your network of audio/video products. 4-Pin-Style vs. 6-Pin-Style Connectors There are two different types of connectors used for IEEE 1394 terminals and cables: a 4-pin and a 6-pin style.
Connecting Compatible IEEE 1394 Devices Compatible IEEE 1394 Devices Compatible A/V devices include some, but not all, cable boxes, D-VHS VCRs, A/V discs, and future products. It is also possible to connect devices to the TV that have IEEE 1394 connectors but are not compatible with the TV or with the NetCommand® control system. Areas of compatibility to consider are: 1. Digital Video Signals The TV is able to decode MPEG2 and DV video as provided by some camcorders.
Helpful Hints for NetCommand Connections Q. My VCR (or other device) does not have two sets of stereo audio outputs. How can I connect this device’s audio to both the TV and the A/V Receiver? A. Connect the single set of stereo audio outputs to the TV only. Use Edit NetCommand® to change the setup of this device. In the Connection screen of “Change” make sure both audio and video for the TV input are check marked and the audio for the AVR input is not check marked.
Chapter 3 NetCommand® Setup and Editing NetCommand® Introduction. . . . . . . . . . . . . . . Using the Remote Control with NetCommand® . NetCommand® Setup On-Screen Buttons. . . . . Menu System. . . . . . . . . 3D Graphical NetCommand® Initial Setup. . . . . . . . . . . . . . . Adding an A/V Receiver. . . . . . . . . . . . . . . . . . Adding Devices. . . . . . . . . . . . . . . . . . . . . . . . Changing or Deleting Devices. . . . . . . . . . . . . . IEEE 1394 Devices and NetCommand® Control..
NetCommand® Introduction NetCommand makes your TV the heart of your Home Theater NetCommand® is an intelligent control system that makes your Mitsubishi TV the heart of your home theater. With NetCommand, the TV sends signals to the other devices in the system via the IR emitters, telling the devices to play, record, change inputs, adjust volume, change channels and many more functions. All of this is accomplished with one remote control and without changing control layers.
Using the Remote Control with NetCommand® Below is a list of several manufacturers’ devices tested and shown to be compatible with NetCommand. These devices can be controlled without changing the setting of the remote control from TV to another product. NetCommand may be able to operate additional models, since many manufacturers use the same control signals to operate some or all of the models they offer. This chart lists only the models that have been tested with NetCommand.
NetCommand® Setup On-Screen Buttons To use the TV’s NetCommand feature, you need to provide some detailed information during the setup of your Mitsubishi TV. You must define the manufacturer of the devices that are connected to the television, or learn the IR code remote control signals for the device connected. For each device, the input to the TV and A/V receiver, and the names for the device are pre-set during Initial NetCommand setup.
3D Graphical Menu System Your TV also has Mitsubishi’s exclusive 3D Graphical on-screen operating system, which provides on‑screen information for menu choices and changes, using the TV’s remote control. Remote Control Buttons Menu Screens A picture (icon) is highlighted on the menu screen when selected with the ADJUST arrows. You may then make changes within the menu or access sub-menus, if available. You can also access sub-menus from a button.
NetCommand® Initial Setup The initial setup screens that appear when you first power on your new Mitsubishi TV guide you through setup of NetCommand and the TV Guide On Screen® system. Most IR remote control signal formats can be learned by NetCommand. Welcome Screen NetCommand (Information) Screen Figure 2 The NetCommand (Information) Screen describes how to start or delay the initial NetCommand and TV Guide On Screen setup.
NetCommand® Initial Setup, continued Device Setup Screen TV Guide On Screen® System Setup If the devices connected to the TV are already in NetCommand memory, you can quickly select them at this screen. Press ADJUST or to move to each device type. Press ADJUST or to select the manufacturer. Select “Other” if the manufacturer is not listed. Later, you can use the Change setting in the Edit NetCommand menu to learn the remote control signals for this device.
NetCommand® Initial Setup, continued Setup Reminder Review Screen Figure 5 After you have made your device choices, the Review Screen will display. It is important to review the settings to ensure that they are correct. If necessary, you can use
Edit NetCommand®: Adding an A/V Receiver A/V Receiver Screen After selecting Next>, the screens that follow are: the Name Screen (Figure 12), Audio Output to AVR screen (Figure 13), ending with the Finish screen (Figure 14). Figure 8 If your A/V Receiver manufacturer was not listed, and you selected “None” during the initial NetCommand setup, you may add the A/V Receiver and have NetCommand learn its remote control’s functions. • If you are in the Finish screen for initial setup, select Edit.
Edit NetCommand®: Adding an A/V Receiver, continued Depending on your A/V Receiver’s capability, you may connect up to seven A/V inputs. Select the number of inputs by pressing ADJUST or . If the number of connected inputs changes, you will need to delete the A/V receiver through Edit NetCommand and add it again, as described above. A/V Receiver (AVR) Input Learn Screen Figure 10 7. Repeat for each connected input. 8.
Edit NetCommand®: Adding an A/V Receiver, continued Name Screen Finish Screen The Name screen allows you to change the default name for the A/V receiver to a custom name of up to eight characters (including a blank space), selecting from letters, numbers, and nine different characters. Using the TV’s remote, press ADJUST or to select each letter, then press ENTER to move to the next position. Press CANCEL to delete the current letter and move back one character position.
Edit NetCommand®: Adding Devices Mitsubishi’s NetCommand allows you to edit your home theater configuration. You can add new devices, change device settings and connections, delete devices and learn remote control IR signals not already in NetCommand memory. Edit NetCommand Screen New Device Screen If you selected Edit when you were at the Finish screen, the Edit NetCommand screen displays. Your choices are: Select “Add” from the Edit NetCommand screen, and the New Device screen will display.
Edit NetCommand®: Adding Devices, continued [Device] Screen Figure 17 If you selected “None” for a device type during initial setup, you can later select the Add option and add a device with this screen. This screen also opens when you select the Change option in the Edit NetCommand screen. • The sample screens here show the choices for adding a VCR; similar screens will appear for any satellite receiver, DVD player, or cable box. Select “Other,” skip Learn and select Next>.
Edit NetCommand®: Adding Devices, continued ADJUST or to select each letter, then press ENTER to move to the next position. Press CANCEL on the remote to delete the current letter and move back one character position. When in the first position, the CANCEL button will return the name to the default name. Figure 18. [Device] Learn screen [Device] Advanced Learn Screen Figure 19 After learning the basic device keys, the [Device] Advanced Learn screen allows you to learn any special keys for your device.
Edit NetCommand®: Adding Devices, continued The screens described below may not be necessary for your device setup. If they do not display automatically on screen, they are not required. VCR for Recordings Screen Figure 22 Select the VCR to use for making analog recordings through NetCommand or the TV Guide On Screen® system. The VCR inputs must be connected to RECORD OUT on the TV, which outputs analog signals converted from digital. Figure 23.
Edit NetCommand®: Changing or Deleting Devices Change Device Screen Finish Screen Selecting Change from the Setup menu screen displays the Change screen. To change a device, select the device by name, not type. You can change the name or input connections to the TV and A/V receiver. If “Other” was selected for the manufacturer then you can also “Learn.” The rest of the screens that follow are the same as when you Add a device.
IEEE 1394 Devices and NetCommand® Control See pages 32 and 33 for information regarding compatible IEEE 1394 devices and connection styles. The TV is not able to control IEEE 1394 devices that use other types of control protocols. Incompatible digital audio, video and/or control information will still be able to pass from one device through the TV to another device on the network. These incompatible devices may not appear on the Device Selection menu or in the Review screen of the Edit NetCommand menu.
Adding IEEE 1394 Devices Automatically Adding IEEE 1394 Devices Automatically Addition of IEEE 1394 devices is a special case of NetCommand setup because the devices are detected automatically. You review, edit, and delete these devices through NetCommand just as you would any other devices. When you connect an IEEE 1394 device to the TV network and power it on, the new device automatically announces its presence. This process is called device discovery and can take up to one minute.
Adding IEEE 1394 Devices Automatically, continued IEEE 1394 Device Type Screen Connection Screen If the new IEEE 1394 device is also connected using analog inputs, you will need to define the device type. Select the type of device, such as a VCR. Select the TV input that you used when you connected the video or S-Video cables. You may also select the TV or A/V receiver input you used when you connected the stereo audio cables.
Chapter 4 NetCommand® Functions Device Selection Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Device Menu Button to Display Menus.. . . . . . . . . . . Using the GUIDE Button to Display ChannelView™ and Menus. . NetCommand®-Controlled Recordings. . . . . . . . . . . . . . . . . . Using TV Disc and A/V Discs.. . . . . . . . . . . . . . . . . . . . . . . . . Peer-to-Peer Connections.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Selection Menu When you press DEVICE on the TV’s remote control, the Device Selection menu (Figure 1) displays. If NetCommand® has not been set up, the Device Selection menu allows you to select an input for viewing. If NetCommand is set up, the Device Selection menu allows you to select the device for viewing, select audio from the TV speakers or A/V receiver, power compatible devices On or Off, and verify the destination of signals.
Using the Device Menu Button to Display Menus Device Menu If the input is a VCR or DVD, and NetCommand is set up, press DEVICE MENU once to display the transport menu for the current device (figure 3). Press DEVICE MENU a second time to display the menu for the current device source, if available. Figure 3. Transport menu When used with the TV Guide On Screen, DEVICE MENU displays or removes TV Guide’s menu information.
Using the GUIDE Button to Display ChannelView™ and Menus The GUIDE Button Please refer to the separate TV Guide On Screen® User’s Guide for details about using the GUIDE button with TV Guide On Screen. When you are not using GUIDE for the TV Guide screens, pressing GUIDE allows you to see NetCommand®-controlled program guides or menus.
NetCommand®-Controlled Recordings Setting up Recordings change the source, channel (if available). Record To device, duration, and day of the week. To change the start time, highlight the Start Time box and press ENTER to move among the hour, minute, and am/pm settings. Use ADJUST to change the settings. Figure 7 Through NetCommand, you can automatically start and stop recordings and send signals from one playback device to a recording device.
NetCommand®-Controlled Recordings, continued Using TV Disc and A/V Discs Direct VCR Recording from an Antenna or Cable Source When your VCR is the current device, REC (record) on the TV’s remote control functions the same as the record button on the VCR’s remote control or front panel. To record directly from antenna or cable: • Method 1 1. Press DEVICE on the TV’s remote to display the Device Selection menu. Highlight the traditional VCR and press POWER to turn on the VCR.
Using TV Disc and A/V Discs, continued Copying or Moving TV Disc or A/V Disc Recordings Tracks you record to disc may have copy restrictions assigned to them. To learn a track’s copy status, highlight a track in the Track List and press INFO. Tracks are assigned one of these ratings: COPY FREE No copy restrictions apply. (or no status shown) COPY NEVER The track cannot be transferred to another recording device. Tracks of this type may have an assigned retention period. See below for more information.
Peer-to-Peer Connections What is a Peer-to-Peer Connection? Figure 9 A peer-to-peer connection allows the IEEE 1394 devices in your TV network to talk to each other without the further need of TV intervention once the peer-to-peer connection is established. With the connection established, you can turn off the TV or use it to watch another device. For example, the TV can set up a connection for an IEEE 1394 cable box that sends a program to another device for viewing.
Chapter 5 TV Menu Operations Main Menu.. . . . . . . . . Setup Menu . . . . . . . . NetCommand® Menu . Record Menu.. . . . . . . Channel Menu .. . . . . . Captions Menu.. . . . . . V-Chip Lock Menu. . . . Audio/Video Menu. . . . Audio Settings. . . . . . . Video Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main Menu Setup Menu Channel Menu Use the Setup menu to select English or Spanish as the language for the menus and on-screen displays. Memorize the available channels for antennas or cable connected to the ANT-1 and ANT-2 inputs. Manually set the time for the TV, or select Auto and the TV will automatically set the time based upon Extended Data Service (XDS) time data. This time data is usually broadcast by your local PBS station. This menu is also used to set the TV timer and reset the lamp reminder.
Setup Menu Setup Menu input are erased and the process starts over from the beginning. Figure 8 After memorizing channels, the channels in memory can be accessed in ascending or descending order by pressing CH or . Select the Channel Menu to access further channel-editing features, such as channel add or delete, channel name, and SQV custom favorite channel memories. When you use a CableCARD™, the complete list of available channels is provided through the CableCARD.
Setup Menu, continued Time Zone Select your correct time zone. Press ADJUST or to select the time zone (Atlantic, Eastern, Central, Mountain, Pacific, Alaska or Hawaii) for your area. Then press ADJUST to move to the Daylight Savings time option. Set Day Select the day or days that the TV will turn on automatically. Press ADJUST or to select Daily, Mon-Fri (Monday through Friday), or the individual days of the week. Daylight Savings Time Select the Daylight Savings time (DST) option that your state uses.
NetCommand® Menu NetCommand Menu Figure 11 Figure 12. Icon Order Menu Figure 11. NetCommand Menu Transport Menu Figure 13 $"#-& %#4 %57 7$3 %7% "6%*0 57 Edit Detailed information regarding setting up and editing the NetCommand menu is found in Chapter 3. The Edit NetCommand screens allow you to add new devices and change traditional and IEEE 1394 devices. You can also set up the TV Guide On Screen® system or turn it on or off.
NetCommand® Menu , continued TV Pause Figure 11 • With TV Pause, you can interrupt watching a program and then resume watching it later without missing any of the program. You can begin watching a program after the start of the broadcast and still be able to view the part already broadcast. This is possible because the TV Pause feature automatically creates a temporary recording on the internal TV Disc.
NetCommand® Menu , continued TimeShuttle Figure 15 With TimeShuttle enabled, the FF and REW keys open a frame-by-frame view of the program. You can then search visually forward or backward to the exact program segment you want to watch. Turn off TimeShuttle if you wish to use the FF and REW keys for standard full-screen video scanning. first pressed the PAUSE key for the current channel and input. TimeShuttle and TV Disc Recordings To Enable TimeShuttle for TV Disc 1. Select On for TimeShuttle. 2.
Record Menu Record Figure 14 The Record menu allows you to set up recordings, view the record list, and set defaults for your recording devices. If you have a digital source and make an analog recording to a VCR, the TV converts the digital signals to analog format and sends the analog output to the VCR through the RECORD OUTPUT jacks. The TV can convert analog programs to digital format. This allows you to record analog programs to a digital recording device (TV Disc, A/V Disc, DVCR).
Record Menu, continued Record List Figure 16 To see a list of all currently programmed recordings, select the record list option on the Record menu or press GUIDE while viewing the Recording setup screen. A maximum of 32 recordings can be scheduled. To cancel a recording on the Record List, press ADJUST or to select the recording, then press CANCEL. To page through the list, press CH or .
Channel Menu Channel Memory Figure 17 After the available channels have been memorized with Memorize Channels on the Setup menu, weaker channels can be added or unwanted channels can be deleted. Press CH or on the remote control to see the channels in memory. Press ADJUST or to select Added or Deleted for the channel shown in the Channel number box. Name Analog channels shown on Antenna-1 or Antenna-2 can be named (up to four characters).
Channel Menu, continued SQV (SuperQuickView™) Using The Menu Screen Figure 17 SQV (SuperQuickView™) allows you to put together lists of your favorite channels from Antenna 1 and Antenna 2. You can store channels in any of the 9 different SQV memory banks. You can also store the same channel in multiple memory banks. Once you have added a channel to an SQV memory, “SQV” and the memory bank number will appear under the tuned channel number on the TV screen. Adding SQV Channels 1.
Captions Menu Background Captions Menu Figure 18 For analog channels, broadcasters can send either Standard or Text closed captioning. Standard Closed Captions follows the dialogue of the characters on screen and displays in a small section of the screen. Text Closed Captions often contain information such as weather or news and covers a large portion of the screen.
Captions Menu, continued Fonts • You can customize the text of digital captions by selecting the font of your choice.
V-Chip Lock Menu V-Chip Lock Menu Overview 3. Press ENTER to confirm the pass code just input. Figure 20 The V-Chip Lock menu gives you access to three different types of TV locks. You must use a pass code to open this menu to enable/disable the lock options. The three different types of locks available are: To reset the pass code, see the procedure in Appendix C. IMPORTANT • V-Chip Lets you restrict access to programming based on program-rating signals sent by the broadcaster.
V-Chip Lock Menu, continued 5. Press ADJUST to move to the TV content categories. • Press ADJUST or to move between categories. • Press ENTER to add check marks to the TV content categories you want to block. 6. Press ADJUST to move to the Programs Not Rated box. Press ENTER to add or delete a check mark to allow or block programs that are not rated. NOTE: Use care when choosing to block unrated programming.
V-Chip Ratings V-Chip Signal Information When provided by the broadcaster, V-Chip ratings can be used to control which programs can be viewed or will be blocked. When V-Chip ratings are sent, you will see the ratings when you change the channel or when you press the INFO button on the remote control. Both TV and Movie ratings will display. TV ratings apply to programs and movies developed for TV and may have supplemental blocking by content categories.
Audio/Video Menu Audio/Video Figure 22 When the original video was filmed on 30-frame-per-second cameras, the Auto setting automatically applies video decoding, the same as used with the Off setting. Film Mode is not effective for high-definition signals. TV Speakers When an A/V receiver has not been set up in NetCommand, this selection will turn the TV’s internal speakers on or off. You may select Off when sending the sound through a separate stereo system or surround sound A/V receiver. Figure 22.
Audio Settings NOTE: The effects of the audio settings of Bass, Treble, Balance and Surround affect the sound heard through the TV speakers only. Analog and Digital Audio Settings as a sound track in a foreign language), or it might be unrelated (such as a weather report). If an SAP signal is broadcast, the letters “SAP” are displayed when you tune to the channel. Mono: Reduces background noise. Use when receiving a weak stereo audio signal. All audio is played mono with this setting.
Video Settings Video Settings adjusting. Each TV input or device has a memory for PerfectColor. While using the PerfectColor option, press CANCEL if you want to reset the colors to the default settings. Press the VIDEO key repeatedly to cycle through the Video options to the one you want to change. Use ADJUST to change settings.
Chapter 6 Additional Features CableCARD™.. . . . . . . . . . . . . . . . . . . . . . . . . MediaCommand™ and Memory Card Playback.. Operation of PIP and POP. . . . . . . . . . . . . . . . . TV Display Formats.. . . . . . . . . . . . . . . . . . . . . On-Screen Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CableCARD™ CableCARD™ Technology CableCARD is a nationwide system standard that allows your local cable TV provider to supply you with an access card customized to your account. This card allows your TV to receive, decode and unscramble the premium digital channels included in your cable TV subscription without the use of a cable box. It also allows your cable provider to automatically update and change your subscription.
MediaCommand™ and Memory Card Playback Warning: Some memory cards available on the market are not properly certified to follow the card type specifications noted below and cannot be used by the card reader. If you experience problems with the reading of your file, please transfer your files to a properly certified card. Memory Card Slots Inserting a memory card 1. Insert a card into a matching card slot on the front of the TV. Be sure to use the correct card slot. Card 1 accepts SmartMedia™.
Media Command™ and Memory Card Playback, continued For MP3 or WMA Playlist Menu: Figure 3 1. Press GUIDE to display the Playlist menu. 2. Press ADJUST or to select different tracks (CH up/down will change pages of the Playlist). Use REW to go to the first track on the page and FF to go to the last track on the page. 3. Press PLAY to begin playback. The Playlist menu will be taken down. The song currently playing will be highlighted.
Operation of PIP and POP The Side-by-Side and PIP/POP features let you view pictures from two different sources at the same time. In summary: View as either main picture or sub-picture • • • • Analog channels Devices on Video/S-Video inputs Devices on Component inputs Devices on either HDMI input View as main picture only • • • • Digital channels received from CableCARD™ or either Antenna input TV Disc IEEE 1394 devices PC images Press PIP/POP to activate the PIP/POP option.
TV Display Formats This is a widescreen TV, also known as a 16:9 TV. This shape reflects the new types of images available from HDTV and many DVDs. There are still many older style narrow-screen images (called 4:3 aspect ratio) you will encounter. While there will never be a perfect solution for displaying a narrow image on a wide screen, Mitsubishi offers several display formats from which to choose. Press FORMAT on the TV remote control to cycle through the available display formats.
TV Display Formats 03*(*/"- 4*(/"- "OBNPSQIJD %7% 03*(*/"- 4*(/"/PO BOBNPSQIJD PS 4% 57 %JTQMBZ 57 %JTQMBZ 4UBOEBSE 4UBOEBSE OPU SFDPNNFOEFE EJTUPSUFE SFDPNNFOEFE OPU BWBJMBCMF GPS )% 4% PS BOBMPH Q J &YQBOE &YQBOE OPU BWBJMBCMF GPS )% 4% PS BOBMPH Q J SFDPNNFOEFE GPS MFUUFSCPYFE OPU SFDPNNFOEFE EJTUPSUFE OPU BWBJMBCMF GPS )% 4% PS BOBMPH Q J ;PPN ;PPN OPU BWBJMBCMF GPS
On-Screen Information When you turn on the TV, change devices, change channels, or when you press the INFO button on the remote control, the TV will display the current status. Below are the most common displays. Please note that seldom or never do all of the different status indicators appear at the same time. Analog Program 1. Antenna or Device being viewed 2. Analog channel being received: If antenna being viewed 3. Channel name (if manually programmed) 4.
Chapter 7 Using the TV with a PC Overview.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Connecting a PC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Computer with an HDMI Monitor Output. . . . . . . . . . . . . . . . . . . . . . 92 Computer with a DVI Monitor Output. . . . . . . . . . . . . . . . . . . . . . . . 93 Computer with a 15-Pin Monitor Output. . . . . . . . . . . . . . . . . . . . . . 93 Adjusting Image Resolution.. .
Connecting a PC Overview 1. Computer with an HDMI Monitor Output Figure 1 An HDMI-to-HDMI cable is required. This is not included with the TV. It may be available at your local electronics retailer Connect the Computer to the TV See the connection diagrams in this chapter to find the method best suited to your needs. 1. 2. Perform NetCommand Setup for the PC • For first-time NetCommand setup: Start NetCommand setup as described in chapter 3 and check mark the PC check box in the Device Setup screen.
Connecting a PC Computer with a 15-Pin Monitor Output Computer with a DVI Monitor Output Figure 2 A DVI-to-HDMI cable or DVI/HDMI adaptor and HDMI cable and audio cables are required. These are not included with the TV. They may be available at your local electronics retailer. 1. Models WD-62927 and WD-73927 Figure 3 A 15-pin PC monitor cable and stereo audio cables are required. These cables are not supplied.
Adjusting Image Resolution Adjusting Image Resolution Figure 4 Your Mitsubishi TV can display resolutions from standard VGA (640 x 480) through XGA (1024 x 768) at 60‑Hz refresh rates. Models WD-62927 and WD-73927 additionally support 1920 x 1080 signals on the 15-pin PC INPUT. See Appendix A in this book for more on compatible screen resolutions. The instructions below are for setting the resolution on most PCs. 1. In the PC’s Start menu, select Settings. 2. Select Control Panel.
PC Display Formats Format VGA 640 X 480 WVGA 848 X 480 SVGA 800 X 600 WSVGA 1064 X 600 Format XGA 1024 X 768 PC720p 1280 X 720 16 X 9 Standard 4 X 3 Standard 1696 X 960 1280 X 960 1696 X 960 1280 X 960 1702 X 960 1280 X 960 1702 X 960 1280 X 960 Standard Zoom 1024 X 768 1280 X 960 1280 X 720 1706 X 960 1365 X 768 1706 X 960 WXGA 1365 X 768 (Accepted via PC Input on models WD‑62927 and WD‑73927) Additional Formats Accepted via PC Input on WD-62927 and WD-73927 Format Reduce Standar
Appendices Appendix A: Appendix B: Appendix C: Appendix D: Appendix E: Appendix F: Appendix G: Appendix H: Appendix I: Appendix J: Specifications.. . . . . . . . . . . . . . . . . . . . NetCommand® Specialized Device Keys. . Bypassing the V-Chip Lock. . . . . . . . . . . Remote Control Programming Codes. . . . Device Control with NetCommand®. . . . . Cleaning and Service. . . . . . . . . . . . . . . . Lamp Cartridge Replacement.. . . . . . . . . Diamond Shield Removal and Installation.
Appendix A: Specifications From time to time, Mitsubishi may offer software updates to expand the features or operation of this TV. When these updates are available they will be announced on our web site, Mitsubishi-tv.com. If you return your owner’s registration card, with your model and serial number, you may receive written notification of available software updates. TV Specifications Projection System DLP, 0.
Appendix A: Specifications, continued PC Input (RGB), Qty. 1 D-Subminiature, 15-Pin PC Monitor Input VGA (640 x 480), 60-Hz WVGA (848 x 480), 60-Hz SVGA (800 x 600), 60-Hz WSVGA (1064 x 600), 60-Hz XGA (1024 x 768), 60-Hz WXGA (1365 x 768), 60-Hz SXGA (1280 x 1024), 60-Hz 720 P 1280 x 720, 60-Hz (EIA standards) 1080P 1920 x 1080, 60-Hz (EIA Standards) Outputs Video, Qty. 1 Signal Type Audio:, Qty. 2 pairs Video: RCA Pin Plug 1.
Appendix B: NetCommand® Specialized Device Keys A/V RECEIVER CABLE or SAT VCR DVD LEARNING SCREEN CHECK BOX NAME FUNCTION NAME ON TV REMOTE X X X X Power* Power On or Power On/Off POWER** X X X X Power (Off)* Power Off POWER** X Volume Up Volume Up VOL X Volume Down Volume Down VOL X Mute Mute MUTE X Analog to Digital* Analog/Digital Switch GUIDE** X Digital to Analog* Digital/Analog Switch GUIDE** X Input (1-7) AVR Input Select Automatic (when device is selected)
Appendix C: Bypassing the V-Chip Lock Lock Bypass Instructions Have Been Filed for Future Reference Bypassing the V-Chip Lock After you set the lock, you need your pass code to view a V-Chip locked program, view the locked TV, cancel the lock, or enter the V-Chip Lock menus. If you forget your pass code, you can view the locked TV without entering your pass code. When you are prompted for your pass code, press the number 9 and QV buttons on the TV remote control at the same time.
This page intentionally blank 102 Appendices
Appendix D: Remote Control Programming Codes IMPORTANT The remote control may return to its initial setting when the batteries are changed. You may need to reprogram. Programming the Remote to Control NetCommand A/V Products 1. Move the slide switch at the top of the remote to the TV position. 2. Press and hold POWER on the remote control. 3. Enter the three digit code of 935, and then release POWER. 4.
Appendix D: Remote Control Programming Codes, continued Cable Boxes, continued SCIENTIFIC ATLANTA SIGNATURE SLMARK SPRUCER STARCOM STARGATE TELEVIEW TOCOM TOSHIBA UNIKA UNITED CABLE UNIVERSAL VIDEOWAY VIEWSTAR ZENITH DVD Players DVD Brand MITSUBISHI AIWA APEX BOSE DENON FERGUSON HARMAN KARDON HITACHI JVC KENWOOD MINTEK NORDMENDE ONKYO ORITRON PANASONIC PHILIPS/MAGNAVOX PIONEER RCA/GE/PROSCAN ROTEL SABA SAMSUNG SAMPO SHARP SYLVANIA SONY THOMSON TOSHIBA V INC.
Appendix D: Remote Control Programming Codes, continued IMPORTANT Some manufacturers may change their products, or they may use more than one remote control system. If this is the case, the TV remote control may not be able to operate your VCR, DVD, cable box, satellite receiver, or A/V receiver. After entering the correct codes in each position of the remote control, use the slide switch to select which product will respond when an operational button is pressed.
Appendix E: Device Control with NetCommand® NetCommand Compatible Traditional Devices (Analog) When Device Selection Menu is Displayed and the Device is Highlighted (Yellow Outline) A/V RECEIVER VCR DVD CABLE BOX/SAT POWER Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) GUIDE Changes between digital and analog audio Changes VCR inputs n/a Changes antenna inputs (RCA model DTC-100 only) FORMAT n/a n/a Changes output between interlaced and progressive
Appendix E: Device Control with NetCommand®, continued IEEE 1394 Devices When Device Selection Menu is Displayed and the Device is Highlighted (Yellow Outline) TUNER/ CABLE BOX/ SAT A/V DISC DVCR AMPLIFIER POWER Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) GUIDE n/a n/a n/a n/a FORMAT n/a n/a n/a n/a Device Remote Control Button When an IEEE 1394 Device is Viewed or Played Device CABLE/SAT TV Disc or A/V DISC DVCR AMPLIFIER Channel up/down
Appendix F: Cleaning and Service IMPORTANT DO NOT use any kind of abrasive cleaner on the surface of the TV screen or Diamond Shield. Cleaning Normally, light dusting with a dry, non-scratching duster will keep your TV clean. If cleaning beyond this is needed, please use the following guidelines: First, turn off the TV and unplug the power cord from the power outlet.
Appendix G: Lamp Cartridge Replacement CAUTION BURN DANGER! During normal operation, the surfaces inside the TV near the lamp are extremely hot. TOUCH THE LAMP CARTRIDGE BY THE HANDLE ONLY Do not touch the glass parts of the lamp cartridge. CAUTION: If the television is on, press POWER to turn it off. Allow the television to cool for one hour before attempting to replace the lamp cartridge. LAMP The light source for this television is a lamp, which is part of a lamp cartridge assembly.
Appendix G: Lamp Cartridge Replacement, continued WARNING THE GRILLE/COVER IS PROVIDED WITH AN INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PURPOSE OR ATTEMPT TO SERVICE THE TV WITHOUT REMOVING THE GRILLE/COVER COMPLETELY. 1. Turn TV power off and allow the lamp to cool at least one hour before proceeding. 2. After the lamp has cooled, remove the plastic air exhaust grille/cover by removing two screws with a #2 (large) Phillips screwdriver. See figure 1. 3.
Appendix H: Diamond Shield Removal and Installation The Diamond Shield ™ is an optional protective cover for the front of the TV screen. Models WD-62927 and WD-73927 come from the factory with the Diamond Shield installed. For Models WD-62827 and 73827, the Diamond Shield may be purchased separately. These instructions explain removal and installation of the Diamond Shield™ and the decorative trim that covers gaps around the TV screen when the shield not installed.
Appendix H: Diamond Shield Removal and Installation, continued 3. Release the six clips that hold the Diamond Shield in place. Work on one side at a time, starting with the top clip. Follow these steps: (1) Refer to figure 4. Hold the plastic card vertically, angled slightly toward the middle of the screen. (2) Insert the card into the channel, alongside the clip. (3) Refer to figure 5.
Appendix H: Diamond Shield Removal and Installation, continued 7. Refer to figure 8 and install the two side-trim pieces as follows: (1) Hook the lower end of the trim over the raised lip running down the side of the TV screen. (2) While keeping the end of the trim hooked on the raised lip, slide the trim down until it meets the lower trim piece. (3) Hold the bottom end of the trim in place and hook the top end on the raised lip that runs along the top edge of the screen.
Appendix I: Recording and Viewing Combinations The tables in this appendix show which program sources you can watch while a recording is in progress.
Appendix J: Troubleshooting General TV Operation Symptom Remarks 1. The TV remote control does not work. • • • • Check that the batteries are installed correctly. Check that the selected switch is set to “TV.” Be no more than 20 feet from the TV when using the remote control. Program the remote control to operate the TV (Appendix D). 2. The TV takes several seconds to respond. • • • • It is normal for digital channels to take longer to tune in. Press ENTER after a channel number to avoid delays.
Appendix J: Troubleshooting, continued General TV Operation Symptom Remarks 14 A device does not respond to button presses from the remote. • Remote has not been set up for NetCommand® use. • The incorrect manufacturer was selected during setup. Select the Change setting from the Setup menu and then the device to display the manufacturer selection. Change if necessary. • The device is not supported and keys have not been learned. • The requested function is not supported by NetCommand.
Appendix J: Troubleshooting, continued Picture Symptom Remarks 1. PIP does not display a picture. • Make sure the V-Chip lock is off. • Not all inputs can be displayed as a PIP. 2. CableCARD channel is not shown as PIP image when CableCARD channel is the main image. Due to the limitations of unidirectional CableCARD service, only one scrambled CableCARD channel can be tuned, viewed, or recorded at a time. 3. There is a large black or gray rectangle on the screen.
Appendix J: Troubleshooting, continued Sound Symptom Remarks 1. There is no sound even when the volume is turned up. • • • • Check audio source in Device Menu. Check to see if the MUTE button is on. The TV’s “Listen to:” setting may be set to SAP. Check that the “TV Speakers” setting is On in the Audio/Video menu. 2. The sound does not match the screen picture. • • • • NetCommand® is set up incorrectly. The TV’s “Listen to:” setting may be set to SAP.
Appendix J: Troubleshooting, continued IEEE 1394 Devices Symptom Remarks 1. Excessive digital artifacts when viewing an IEEE 1394 device. • The IEEE 1394 cable is too long; 15 feet between devices is the maximum. • There may be a slow device in the middle of the IEEE 1394 network. Move the slow devices to the end so that connections for faster devices do not pass through them. 2. D-VHS recordings for digital cable have drop-outs (loss of picture or sound), or no playback.
Appendix J: Troubleshooting, continued IEEE 1394 Devices Symptom Remarks 10. Cannot record to or from the IEEE 1394 device, including dubbed recordings. • To initiate a recording to IEEE 1394 device, press the REC key. The Record menu displays allowing setup of the recording. • The source device for the recording is not powered on. • When dubbing, the destination device for the recording is not powered on.
Trademark and License Information LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. CableCARD™ is a trademark of Cable Television Laboratories, Inc. CompactFlash® and CF are trademarks of the CompactFlash Association.
MITSUBISHI TV SOFTWARE END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and Mitsubishi Digital Electronics America, Inc. (MDEA) for all software pre installed and/or provided along with this television (“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
Mitsubishi DLP™ Projection Television Limited Warranty MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants as follows to the original purchaser of this television from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of against defects arising from improper workmanship and/or material: a. Parts. The lenticular (i.e.
d. To obtain a replacement lamp during the warranty period, please contact the MDEA Consumer Relations Department at (800) 332-2119. After the warranty period you may order the lamp directly from the MDEA Parts Department at (800) 553-7278. 2. THIS LIMITED WARRANTY DOES NOT COVER: a. Up to .01% pixel outages (small dot picture elements that are dark or incorrectly illuminated). b.
Index A A/V Memory Reset. See Reset A/V Receiver Adding 43 Connecting 27 Inputs 43 Input Learn Screen 44 Learn Screen 44 A/V Reset. See Reset A/V Settings Descriptions Audio 80 Video 81 Accessories, TV 10 Add Device. See NetCommand Advanced Learn Screen, [Device] 48 Anamorphic Picture Format 71 Antenna inputs (ANT-1 MAIN, ANT-2 AUX) 18 Antenna with Leads, Connecting 24 Audio/Video Menu 64, 79 Audio Inputs 18 B Back Panel (illustrated) 18 Batteries.
N Name Screen 45, 48 NetCommand Add Device 46 Change Device 50 Connecting External Devices 22 Default Inputs 22 Delete Device 50 Description 11 Device Control (reference chart) 106 Device Setup Screen 41 Edit NetCommand Screen 46 Initial Setup 40 IR Emitters 31 NetCommand Menu 67 Pre-Memorized Devices 37 Specialized Device Keys 100 O On-Screen Information 90 P Pass Code Resetting 101 Setting 76 Pause.
Website: www.mitsubishi-tv.com E-mail: MDEAservice@mdea.com To order replacement or additional remote controls, lamp cartridges, or Owner’s Guides, call 800-553-7278 For questions, call Consumer Relations at 800-332-2119 © 2005 Mitsubishi Digital Electronics America, Inc. 853B540A40v3 Written and Printed in U.S.A.
