Operation Manual

ManualsBrandsMitsubishi ManualsTVWL-82913

Table Of Contents

Owner’s Guide Book 1

WL-82913

Connections and Maintenance

�

visit our website at

w w w.mit s u bish i -t v.com

Summary of content (140 pages)

PAGE 1
� Owner’s Guide Book 1 WL-82913 Connections and Maintenance visit our website at w w w. m i t s u b i s h i -t v.
PAGE 2
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude to constitute a risk of electric shock.
PAGE 3
Contents CHAPTER 1 Television Overview Unpacking the TV’s Accesories.............................................................................. 8 TV Delivery and Installation, Cabinet Assembly................................................... 9 TV Delivery and Installation, Diamond Shield™ Installation and Removal ..... 11 TV Delivery and Installation, Arc Assembly ....................................................... 12 Special Features.................................................................
PAGE 4
IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference.Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference. Follow all operating and use instructions. 2. Heed Warnings Adhere to all warnings on the appliance and in the operating instructions. 3.
PAGE 5
IMPORTANT SAFEGUARDS, cont’d. 12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 13.
PAGE 6
Our Thanks... Thank you for choosing Mitsubishi as your premier Home Entertainment provider. This Owner’s Guide describes the features and functions of your Mitsubishi widescreen, high definition TV. We urge you to examine this Owner’s Guide to become familiar with the innovative features and operations this unique television offers. The very core of our corporate philosophy is to provide our customers with the very best.
PAGE 7
Chapter . . . 1 Television Overview Unpacking the TV’s Accesories .................................................8 TV Delivery and Installation, Cabinet Assembly.......................9 TV Delivery and Installation, Diamond Shield™ Installation and Removal ............................................................................... 11 TV Delivery and Installation, Arc Assembly ...........................12 Special Features ........................................................................
PAGE 8
Unpacking the TV’s Accessories Please take a moment to review the following list of items to ensure that you have received everything including: CABLE/DBS/DTV VCR DVD AUDIO TV 1 2 3 4 5 6 7 8 9 SQV 0 QV CH VOL POWER DEVICE GUIDE 3. (One) Digital Audio Cable MUTE TVMENU HOME DEVICE MENU CANCEL V-CHIP INFO PIP/POP PIP CH PIP DEVICE AUDIO VIDEO EXCH SLEEP FORMAT CONNECT REC PAUSE 4. (One) Double IR Emitter Cable PLAY FF/FWD REW/REV STOP 1. Remote Control �� 5.
PAGE 9
TV Delivery and Installation, Cabinet Assembly ��
PAGE 10
TV Delivery and Installation, Cabinet Assembly, continued ��
PAGE 11
TV Delivery and Installation, Diamond Shield™ Installation and Removal ��
PAGE 12
TV Delivery and Installation, Arc Assembly Installation ��
PAGE 13
TV Delivery and Installation, Arc Assembly Installation, continued ��
PAGE 14
Special Features Your new High Definition bigscreen television has many special features that make it the perfect center of your home entertainment system. These special features include: High Definition 3-chip LCoS Display System Your Mitsubishi bigscreen HDTV uses the latest in display technology -- Liquid Crystal on Silicon or LCoS. This system uses three LCoS chips (one chip for each of the primary colors of red, green and blue), each with a 1920 x 1080 pixel pattern to create the image.
PAGE 15
Front Control Panel Buttons �� The buttons on the Front Control Panel highlighted in gray are duplicated on the remote control. The top row of labels show the control functions when there are no TV menus displayed on the screen.
PAGE 16
Front Control Panel Memory Card �� Input 3 This input can be used for convenient connection of a camcorder or other video device to the TV. Please note that if you connect to the S-VIDEO terminal, the VIDEO terminal is deactivated. The VIDEO terminal is active when there is no S-Video connection.
PAGE 17
Back Panel ��
PAGE 18
Back Panel, continued NOTE: When MonitorLink is used as a DVI-HD input, the terminal is compliant with EIA-861 standards for extended and high definition video and is not intended for use with personal computers or devices outputting video signals with computer resolution. 12. Input DTV (480i/480p/720p/1080i) This input is used to connect an external DTV receiver, and can be configured for YPrPb or RGB plus H&V signal types. Please see Appendix B for signal compatibility. 7.
PAGE 19
Chapter . . . 2 Connecting and Appendixes External Devices & NetCommand® Setup..............................20 NetCommand ® Pre-Memorized Devices ................................21 Antenna or Wall Outlet Cable for Digital Broadcasts.............22 Separate UHF and VHF Antennas for Analog Broadcasts ....23 Single Analog Antenna or Wall Outlet Cable...........................24 Cable Box....................................................................................
PAGE 20
Connecting External Devices & NetCommand® Setup NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to each device. NetCommand is also able to learn the remote control signals used by most audio video devices not already in the TV’s memory. NetCommand will also automatically switch the TV and compatible or learned Audio/Video (A/V) Receivers to the correct input used with each device.
PAGE 21
NetCommand® Pre-Memorized Devices Below is a list of several manufacturers devices tested and shown to be compatible with the NetCommand control system. When you use these devices you will be able to control them without changing the setting of the remote control from TV to another product. NetCommand may be able to operate additional models since many manufacturers use the same control signals to operate some or all of the models they offer.
PAGE 22
Connecting Antenna or Wall Outlet Cable for Digital Broadcasts Antenna or Wall Outlet Cable for Digital Broadcasts Figure 1 For cable or antenna with coaxial lead Connect the incoming cable to ANT-DTV on the TV back panel. Antenna or Wall Outlet Cable for digital broadcasts Mitsubishi strongly recommends against using antennas with twin flat leads. Twin flat lead antenna wires are subject to interference which may adversely affect the performance of the TV. We recommend using coaxial antenna cable.
PAGE 23
Connecting Separate UHF and VHF Antennas for Analog Broadcasts Separate UHF and VHF Antennas for Analog Broadcasts Figure 2 1. Connect the UHF and VHF antenna leads to the UHF/VHF combiner. 2. Push the combiner onto ANT-A on the TV back panel. Note: UHF/VHF combiners are not provided with the TV. They should be available at most electronic stores.
PAGE 24
Connecting a Single Analog Antenna or Wall Outlet Cable Single Analog Antenna or Wall Outlet Cable Figure 3 For antennas with twin flat lead 1. For antenna with twin flat leads, connect the 300 Ohm twin leads to the 300 Ohm to 75 Ohm transformer. 2. Push the 75-Ohm side of the transformer onto ANT-A on the TV back panel. Note: 300-Ohm to 75-Ohm matching transformers are not provided with the TV. They should be available at most electronic stores. For cable or antenna with coaxial lead 3.
PAGE 25
Connecting a Cable Box Cable Box Figure 4 1. Connect the incoming cable to ANT-A on the TV back panel. Note: Connect two coaxial cables as follows: 2. One from LOOP-OUT on the TV back panel to IN on the cable box back panel. 3. One from OUT on the cable box back panel to ANT-B on the TV back panel. Note: NetCommand assumes that your Cable Box will be connected to Ant-B or your VCR. Also, Channel 3 is the default output channel for the Cable Box.
PAGE 26
Connecting an Analog VCR to Analog Antenna or Wall Outlet Cable Analog VCR to Analog Antenna or Wall Outlet Cable Figure 5 1. Connect the incoming cable to ANT-A on the TV back panel. Connect two coaxial cables as follows 2. One from LOOP-OUT on the TV back panel to ANTENNA IN on the VCR back panel. 3. One from VCR back panel ANTENNA OUT to ANT-B on the TV back panel. 4. Now complete Connecting Composite Video or S-Video and Audio Connections step 1 and 2 on page 28.
PAGE 27
Connecting an Analog VCR to a Cable Box Analog VCR to a Cable Box Figure 6 1. Connect the incoming cable to ANT-A on the TV back panel. Note: Connect three coaxial cables as follows: 2. One from LOOP-OUT on the TV back panel to IN on the back of the cable box. 3. One from OUT on the back of the cable box to ANTENNA IN on the VCR back panel. 4. One from ANTENNA OUT on the VCR back panel to ANT-B on the TV back panel. 5.
PAGE 28
Connecting an Analog VCR, continued Analog VCR with Composite Video or S-Video with Audio Connections Figure 7 1. Connect a video cable from VIDEO OUT on the VCR back panel to VIDEO INPUT 1 on the TV back panel. Note: If you have an S-VHS VCR, follow the same steps using the S-Video terminals on the VCR and TV (in place of the composite terminals). 2. Connect a set of audio cables from AUDIO OUT on the VCR back panel to AUDIO INPUT 1 on the TV back panel.
PAGE 29
Connecting an Audio/Video Surround Sound Receiver or Stereo System A/V Surround Sound Receiver or Stereo System Figure 8 1. Connect a set of audio cables from the MONITOR OUTPUT AUDIO 2 on the back of the TV to the TV AUDIO INPUT on the back of the A/V Receiver. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel. When you connect a digital A/V Receiver with Dolby Digital™ surround sound: 2.
PAGE 30
Connecting a DVD Player with Component Video DVD Player with Component Video Figure 9 1. Connect the Component Video cables from Y/Pr/Pb VIDEO OUT on the back of the DVD player to COMPONENT-1 on the TV back panel, matching the correct connection: • Y to Y • Pr to Pr • Pb to Pb 2. Connect a set of audio cables from AUDIO OUT on the back of the DVD player to COMPONENT-1 AUDIO Input on the TV back panel. The red cable connects to the R (right) channel, and the white cable connects to the L (left) channel.
PAGE 31
Connecting a Satellite Receiver with S-Video Satellite Receiver with S-Video Figure 10 1. Connect an S-Video cable from VIDEO OUT on the satellite receiver back panel to the S-VIDEO input of AUDIO VIDEO INPUT-2 on the TV back panel. 2. Connect a set of audio cables from AUDIO OUT on the satellite receiver back panel to the AUDIO INPUT-2, on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.
PAGE 32
DTV Connectors and Adaptors DTV Connectors and Adaptors Figure 11 The TV back panel has 5 RCA-type connectors for the Input-DTV. The back panel of your external DTV receiver may use RCA-type connectors or BNC-type connectors. If your DTV receiver comes with BNC type connections, you will need to purchase BNC to RCA adaptors to connect the TV to the DTV receiver. These adaptors should be available at most electronic supply stores.
PAGE 33
Connecting an External Digital TV (DTV or HDTV) Receiver with Component Video Connections External Digital TV (DTV or HDTV) Receiver with Component Video Connections Figure 12 1. Connect the outside antenna, cable or satellite to ANT or SATELLITE IN on the DTV receiver (see your DTV receiver’s owner’s guide for instructions and cable compatibility). 2.
PAGE 34
Connecting an External Digital TV (DTV or HDTV) Receiver with RGB, HV Video Connections External Digital TV (DTV or HDTV) Receiver with RGB, HV Video Connections Figure 13 1. Connect the outside antenna, cable or satellite to ANT or SATELLITE IN on the DTV receiver (see your DTV receiver owner’s guide for instructions and cable compatibility). 2.
PAGE 35
Connecting MonitorLink™ with MonitorLink Control or DVI-HD MonitorLink and MonitorLink Control Figure 14 1. Connect a MonitorLink cable from the Mitsubishi Receiver/Controller back panel to the TV back panel. 2. Connect the L (left) and R (right) audio cables from the Mitsubishi Receiver/Controller to AUDIO LEFT and AUDIO RIGHT on the MonitorLink section of the TV back panel. 3. Connect the MonitorLink Control cable from the Mitsubishi Receiver/Controller back panel to the TV back panel.
PAGE 36
Connecting a Computer with a PC Monitor Output Computer with a PC Monitor Output Figure 15 1. Connect PC Monitor Out from the computer to PC Input on the TV back panel using a PC compatible monitor cable. See Appendix B in book 2 for PC signal compatibility. 2. Connect the L (left) and R (right) audio cables from the computer to PC AUDIO on the TV back panel. In cases where your computer’s audio output is a single mini-jack, a splitter is needed to complete this connection.
PAGE 37
Connecting the IR Emitter NetCommand® or IR Repeater IR Emitter NetCommand ® or IR Emitter Repeater After you have used 1A or 1B, IR Emitter NetCommand 2. Run the cable for each of the emitter ends under, along side or over the top of each device to be controlled to the area of the front where the remote control sensor is located. 1A.Connect the plug end of the supplied Quadruple IR Emitter Cable to one of the IR Output NetCommand jacks on the TV back panel. 3.
PAGE 38
Connecting: Helpful Hints Q My VCR (or other device) does not have two sets of stereo audio outputs; how can I connect this device’s audio to both the TV and the A/V Receiver? A. There are two solutions: 1. Connect the single set of stereo audio outputs to the TV only. Use the Edit NetCommand® feature to “Change” the setup of this device.
PAGE 39
Appendix A: Cleaning and Service Cleaning Normally, light dusting with a dry, non-scratching duster will keep your TV clean. If cleaning beyond this is needed, please use the following guidelines: First, turn off the TV and unplug the power cord from the power outlet. Top and Sides of the TV: • Gently wipe down your TV with a soft, non-abrasive cloth such as cotton flannel or a clean cloth diaper, lightly moistened with water. Dry with a second dry, soft, non-abrasive cloth.
PAGE 40
Appendix A: Cleaning the Dust Filter ��
PAGE 41
Appendix B: Lamp Cartridge Replacement ��
PAGE 42
Appendix B: Lamp Cartridge Replacement, continued ��
PAGE 43
Using The System Reset Button If the TV doesn’t respond to either the remote control or the front panel controls or will not power off, press the SYSTEM RESET button on the front panel with a pointed item such as the point of a ball point pen or end tip of a paperclip. The TV will turn off and the green led will flash quickly for about one minute. When the green led stops flashing, you may turn on the TV again.
PAGE 44
LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. This product incorporates copyright protection technology that is protected by U.S.
PAGE 45
Index F Front Control Panel Buttons 15 A Memory Card 16 Antenna or Wall Outlet Cable for Digital Broadcasts, Connecting 22 Arc Assembly 12-13 A/V Surround Sound Receiver or Stereo System, Connecting 29 B Back Panel 17-18 H Helpful Hints, Connecting 38 I Important Safeguards 4 IR, Emitter NetCommand® 37 Repeater 37 C Cabinet Assembly 9-10 Cable Box Connecting 25 and Analog VCR, Connecting 27 Cleaning and Service 39 Cleaning the Dust Filter 40 Computer with a PC Monitor Output, Connecting 36 Connecti
PAGE 46
MITSUBISHI LCoS PROJECTION TELEVISION LIMITED WARRANTY MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants to the original purchaser of this television that if purchased from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of improper workmanship and/or material: a. Parts. The diffusion (i.e. front picture) screen and/or the Diamond Shield™ is warranted against defects in materials and workmanship for a period of 30 days.
PAGE 47
MITSUBISHI TV SOFTWARE END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and Mitsubishi Digital Electronics America, Inc. (MDEA) for all software preinstalled and/or provided along with this television (“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
PAGE 48
� If you have questions regarding your television, call Consumer Relations at (800) 332-2119, or email us at M D E A s e r v i c e @ b i g s c re e n . m e a . c o m To order replacement or additional remote controls or owner’s guides call (800) 553-7278 or visit our website at w w w.m i t s u b i s h i -t v.c o m © 2003 Mitsubishi Digital Electronics America, Inc. 871D387A10 Designed and Printed in the U.S.
PAGE 49
Owner’s Guide Book 2 WL-82913 Operation visit our website at w w w. m i t s u b i s h i -t v.
PAGE 50
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user of the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be sufficient magnitude to constitute a risk of electric shock.
PAGE 51
Contents Chapter 1: Basic Functions Unpacking the TV’s Accessories .................................................................................................. 8 Special Features ........................................................................................................................... 9 Front Control Panel Buttons ......................................................................................................... 10 Front Control Panel Memory Card................................
PAGE 52
IMPORTANT SAFEGUARDS Please read the following safeguards for your TV and retain for future reference.Always follow all warnings and instructions marked on the television. 1. Read, Retain and Follow All Instructions Read all safety and operating instructions before operating the TV. Retain the safety and operating instructions for future reference. Follow all operating and use instructions. 2. Heed Warnings Adhere to all warnings on the appliance and in the operating instructions. 3.
PAGE 53
IMPORTANT SAFEGUARDS, cont’d. 12. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 13.
PAGE 54
6
PAGE 55
Chapter . . . 1 Basic Functions Unpacking the TV’s Accessories ................................................... 8 Special Features .............................................................................. 9 Front Control Panel Buttons ......................................................... 10 Front Control Panel Memory Card ............................................... 11 Remote Control Functions: Overview..........................................
PAGE 56
Unpacking the TV’s Accessories Please take a moment to review the following list of items to ensure that you have received everything including: CABLE/DBS/DTV VCR DVD AUDIO TV 1 2 3 4 5 6 7 8 9 SQV 0 QV CH VOL POWER DEVICE GUIDE 3. (One) Digital Audio Cable MUTE TVMENU HOME DEVICE MENU CANCEL V-CHIP INFO PIP/POP PIP CH PIP DEVICE AUDIO VIDEO EXCH SLEEP FORMAT CONNECT REC PAUSE 4. (One) Double IR Emitter Cable PLAY FF/FWD REW/REV STOP 1. Remote Control AA 5.
PAGE 57
Special Features Your new High Definition bigscreen television has many special features that make it the perfect center of your home entertainment system. These special features include: High Definition 3-chip LCoS Display System Your Mitsubishi bigscreen HDTV uses the latest in display technology -- Liquid Crystal on Silicon or LCoS. This system uses three LCoS chips (one chip for each of the primary colors of red, green and blue), each with a 1920 x 1080 pixel pattern to create the image.
PAGE 58
Front Control Panel Buttons �� The buttons on the Front Control Panel highlighted in gray are duplicated on the remote control. The top row of labels show the control functions when there are no TV menus displayed on the screen.
PAGE 59
Front Control Panel Memory Card �� Input 3 This input can be used for convenient connection of a camcorder or other video device to the TV. Please note that if you connect to the S-VIDEO terminal, the VIDEO terminal is deactivated. The VIDEO terminal is active when there is no S-Video connection.
PAGE 60
Remote Control Functions: Overview Overview Figure 1, following page and to navigate menus, change settings, and move the PIP on-screen location. Also operates many NetCommand® functions. 1. Slide Switch: Select A/V product to be controlled by the remote control. Move to TV for NetCommand® device control. 2. Numbers: Individually select channels or enter information into menus. 15. DEVICE MENU: Display menus for devices connected to TV. 3.
PAGE 61
Remote Control Functions: Operation and Care Operation Figure 2 Installing the Batteries: CABLE/DBS/DTV VCR DVD AUDIO TV 1 1 2 3 4 5 6 7 8 9 SQV 4 0 QV 7 CH 8 VOL DEVICE 3 POWER 6 9 11 10 MUTE HOME CANCEL 16 15 V-CHIP INFO 17 18 19 20 PIP/POP EXCH SLEEP 22 23 PIP CH 21 AUDIO PIP DEVICE 25 FORMAT 26 28 REC 30 REW/REV 34 12 13 DEVICE MENU 2. Load the batteries, making sure the polarities (+) and (-) are correct.
PAGE 62
14
PAGE 63
Chapter . . . 2 NetCommand® Functions Programming the Remote to Control NetCommand® A/V Products .................................................................................. 16 3D Graphical Menu System ............................................. 17 Using the Remote Control with NetCommand® Setup ............. 18 NetCommand® Initial Setup Guide .............................................. 19 NetCommand Editing Guide .........................................................
PAGE 64
Programming the Remote to Control NetCommand® A/V Products To Program the Remote to Control NetCommand A/V Products Figure 3 (See NetCommand Supported Devices, for the list of A/V products supported by the NetCommand System.) 1. Move the slide switch at the top of the remote to the TV layer. 2. Press and hold the POWER button on the remote control. 3. Enter the three digit code of 935, and then release the POWER button on the remote control. 4.
PAGE 65
3D Graphical Menu System Your TV has a special control system called NetCommand® that will control IEEE 1394 devices, selected IR devices and learn IR code to control other devices. For details on operating these control features, see the next page. Your TV also has Mitsubishi’s exclusive 3D Graphical on-screen operating system, which provides on-screen information for menu choices and changes, using the TV’s remote control.
PAGE 66
Using the Remote Control with NetCommand® Setup In order to use the NetCommand feature, you need to provide some detailed information during the setup of your Mitsubishi TV. You must define the Manufacturer of the devices that are connected to the television or learn the IR code remote control signals for the device connected. For each device, the input to the TV and A/V receiver and the names for the device are pre-set during Initial NetCommand setup.
PAGE 67
NetCommand® Initial Setup Guide The easiest way to setup NetCommand is to follow the on-screen directions. For reference, below is a list of the screens that you will use during the initial setup. You will find detailed information regarding each screen in the pages following this Guide. Initial Initial NetCommand Setup: When you first turn on your TV. You may Cancel at any screen. Language Screen Page 21 Figure 1 Information Screen Page 21 Figure 2 Device Setup Screen (used when manufacturer is known).
PAGE 68
NetCommand® Editing Guide After initial setup, the screens listed below may display, depending on your selection. The easiest way to setup NetCommand is to follow the on-screen directions. You will find detailed information regarding each screen in the pages following this Guide.
PAGE 69
NetCommand® Initial Setup When you first power On your new Mitsubishi TV, the initial setup screens appear. In order to use NetCommand, select these screens after you have connected the compatible equipment to the TV. Most IR remote control signal formats can be learned by NetCommand. Language Screen Device Setup Screen Figure 1 When you first turn on your TV, the Welcome screen displays and asks you to select either English or Spanish as the language for the on-screen menus.
PAGE 70
NetCommand® Initial Setup, continued Review Screen Finish Screen After you have made your device choices the Review Screen will display. It is important to review the settings to ensure that they are correct. If necessary, you can use
PAGE 71
Edit NetCommand®, Adding an A/V Receiver A/V Receiver Screen Figure 6 If you selected “None” as the manufacturer of the A/V Receiver connected to the TV during the initial NetCommand Setup, you may Add the A/V Receiver and have NetCommand learn it. The same screens are displayed when editing the A/V Receiver settings, using Edit NetCommand. 3. Select “Other”, skip Learn and select Next>. This will allow the device to appear and will allow NetCommand to switch inputs to use this device.
PAGE 72
Edit NetCommand®, Adding an A/V Receiver, continued A/V Receiver Input Learn Screen Figure 8 NetCommand can now learn the remote control signals used to select each input on the A/V Receiver. A/V Receiver Learn Screen Figure 9 1. Press ADJUST or on the TV remote to select the check box for each function to be learned. 1. Press ADJUST or on the TV remote to select the check box for each function to be learned. 2. Press ENT(er) and the name will begin to flash to confirm the ready-to-learn status. 2.
PAGE 73
Edit NetCommand®, Adding an A/V Receiver, continued Name Screen Figure 10 The Name screen allows you to change the default name for the A/V Receiver to a custom name of up to eight characters (including a blank space), selecting from letters, numbers, and nine different characters. Using the remote, press ADJUST and to select each letter, then press ENT(er) to move to the next position. Press CANCEL to delete the current letter and move back one character position.
PAGE 74
Edit NetCommand®, Adding Devices Mitsubishi’s NetCommand offers the ability to edit your home theater configuration so that you can add new devices, change device settings and connection inputs, delete devices and even learn the remote control IR signals of devices that are not already in the NetCommand memory. NOTE: Select Next>, then press ENT(er) at each screen, to move forward to the next screen.
PAGE 75
Edit NetCommand® Adding Devices, continued [Device] Screen Figure 15 If you selected “Other” in the Initial NetCommand Setup screen, then you can edit the device name and start learning. If you selected “None”, then you can add a device. If you have added a new device or changed an input in your home theater system, use this screen to start learning.
PAGE 76
Edit NetCommand®, Adding Devices, continued Please refer to the Guide on page 20 to see if the screen described below is necessary for your device setup. [Device] Advanced Learn Screen Connection for [Device] Screen After learning the basic device keys, the [Device] Advanced Learn screen allows you to learn any special keys for your device. Most common IR remote control signal formats can be learned by NetCommand.
PAGE 77
Edit NetCommand®, Adding Devices, continued Please refer to the Setup Guide on page 20 to see if the screen described below is necessary for your device setup. RF Connection for Cable Screen Input-DTV Connection Screen The RF Connection screen displays only when Adding or Changing a Cable Box. If your Cable Box is connected to a TV Antenna input, make sure the RF checkbox is checked. Select the TV antenna input that is used with the Cable Box.
PAGE 78
Edit NetCommand®, Change or Delete Devices, Finish Screen Change Finish Screen Selecting Change from the Setup menu screen, displays the Change screen. To change a device, select the device by name, not type. You can change the name or input connections to the TV and A/V Receiver. If “Other” is selected for the manufacturer then you can also “Learn”. The rest of the screens that follow are the same as when you Add a device.
PAGE 79
Chapter . . . 3 Device Selection Connecting IEEE 1394 Devices .................................................... 32 Automatically Adding IEEE 1394 Devices.................................... 34 Device Selection Menu.................................................................. 36 PIP Device Selection Menu Displaying and Using the Transport Menu.............................................................................. 37 Channel Selection, Sleep Timer, Audio and Video Buttons ......
PAGE 80
Connecting IEEE 1394 Devices 4-Pin Style vs. 6-Pin Style There are two different types of connectors used for IEEE 1394 terminals and cables, a 4-pin and a 6-pin style. 4 pin connector � �� The 4-pin connector is capable of sending digital audio signals, digital video signals and digital control signals back and forth between devices. Your TV has three 4-pin type connection jacks available, one on the front panel and two on the back panel.
PAGE 81
Connecting IEEE 1394 Devices, continued When Connecting IEEE 1394 Devices • Do not loop the last device in the chain back to the TV. When the device chain is looped, the TV may not be able to work with the other devices. • Place devices that have only a mechanical (two-position) power switch at the end of the chain or leave the power switch in the ON position. When turned OFF, IEEE 1394 signals may not be able to pass through the device to other devices.
PAGE 82
Automatically Adding IEEE 1394 Devices IEEE 1394 Device Type Screen Connection Screen If the new IEEE 1394 device is also connected using analog inputs, you will need to define the device type. Select the type of device, such as a VCR. Select the TV input that you used when you connected the video or S-Video cables. You may also select the TV or A/V Receiver input you used when you connected the stereo audio cables. Match the input names for the TV Input and A/V Receiver Input selections.
PAGE 83
Automatically Adding IEEE 1394 Devices, continued Compatible IEEE 1394 Devices It is possible to connect devices to the TV that have IEEE 1394 connectors but are not compatible with the TV or with the NetCommand® control system. There are three areas of compatibility to consider: 1. Digital Video Signals The TV is able to decode MPEG2 video. Other types of digital video, such as DV video, provided by some camcorders, must be decoded by the source device and sent to the TV as analog video or S-Video.
PAGE 84
Device Selection Menu When you press DEVICE on the TV’s remote control, the Device Selection menu (Figure 1) displays. If NetCommand® has not been setup, the Device Selection menu allows you to select an input for viewing. When NetCommand is setup the Device Selection menu allows you to select the device for viewing, select audio from the TV speakers or A/V Receiver, power compatible devices On or Off, and verify the destination of signals.
PAGE 85
PIP Device Selection Menu, Displaying and Using the Transport Menu PIP Device Selection Menu Figure2 When you press the PIP DEVICE button on the remote control, the PIP Selection menu displays. The PIP Selection menu display is similar to the Device Selection menu except the Video Section shows the destination for the video is the PIP/POP and the Audio and Connection Sections are not displayed.
PAGE 86
Channel Selection, Sleep Timer, Audio and Video Buttons Channel Selection There are three methods to select Antenna A or Antenna B channels: 1. Enter three numbers (for channel 2, press 002). 2. Press the channel number and ENT(er). Example: for channel 2, press 2, then ENT(er). 3. Enter the channel number and wait four seconds. The TV will change automatically. For Antenna DTV: 1. Enter two or three numbers for the major channel number.
PAGE 87
NetCommand® Controlled Recordings Recording Setup Figure 4 Your TV is able to start and stop recordings automatically and send the signals from one external playback device to another external recording device. It is also able to convert digital signals from Antenna DTV and from IEEE 1394 devices to analog signals that can be recorded on NetCommand compatible analog VHS and S-VHS VCRs.
PAGE 88
NetCommand® Controlled Recordings, continued Record List Screen Figure 5 To view a list of all of your currently programmed recordings, select List from the Record screen. A maximum of 32 recordings can be scheduled. To cancel a recording on the Record List, press ADJUST or to select the recording, then press CANCEL. To page through the list, press CH or .
PAGE 89
Chapter . . . 4 TV Menu Screen Operations Menu Screens Choices ................................................................. 42 Setup Menu .................................................................................... 43 Antenna Menu ................................................................................ 44 Time Menu ...................................................................................... 46 Captions Menu ....................................................................
PAGE 90
Main Menu Choices Setup V-Chip Lock Add, change, review or delete NetCommand® settings and devices. You can also change the order of icons displayed on the Device Selection menu, select energy mode, turn on or off the transport menu, and select English or Spanish as the language for the menus and onscreen displays. Block or allow programing based upon rating signals sent by the broadcast station, lock by time, or disable or re-enable the front panel buttons. Figure 1 Figure 5 Figure 5.
PAGE 91
Setup Menu Setup Menu Figure 8 Select Setup to perform the following functions. Transport Menu The Transport Menu is used by NetCommand® to control VCRs, DVDs, IEEE 1394 AV Disc, digital VCRs, and similar devices. This menu can be turned off if you would rather not have it displayed. The transport buttons on the remote control will continue to operate these devices. See page 37 for more detailed information regarding this feature. Energy Mode Figure 8.
PAGE 92
Antenna Menu: Antenna, Memorize Channels, Channel, Memory and Name Antenna Menu The following Antenna Menu options are available for use on Antenna A, Antenna B or Antenna DTV. You can memorize channels, add or delete channels, and add channels to an SQV (Super Quick View™) list. For Antenna A, Antenna B, you can name channels. Antenna Menu Channel Select Antenna to perform the following functions.
PAGE 93
Antenna Menu: SuperQuickView™ (SQV) SQV (SuperQuickView™) Using The Menu Screen Figure 10 SQV (SuperQuickView™) allows you to put together lists of your favorite channels from Antenna A, Antenna B and Antenna DTV. You can store channels in any of the 9 different SQV memory banks. You can also store the same channel in multiple memory banks. Once you have added a channel to an SQV memory, “SQV” and the memory bank number will appear under the tuned channel number on the TV screen. Adding SQV Channels 1.
PAGE 94
Time Menu: Setting the Clock, Manual or Auto Time Menu Setting the Clock (Auto) Select Time to perform the functions listed below. The Clock Setting (Auto) will automatically set the day and time using Extended Data Service (XDS) time data. This data is automatically retrieved from a PBS channel or other channel carrying this service when received on Ant-A or Ant-B. Be aware that some channels may send incorrect time information; this is not a defect in the TV.
PAGE 95
Time Menu: Setting The Timer Timer On/Off Figure 13 Device The timer can be turned to On or Off. When On, you need to select the time to turn On, the day to turn On, the device and the channel to display. At your preselected time, the timer will turn the TV On, and a message will be displayed, “Press a button for the TV to stay on”. Any button on the remote control must be pressed within 5 minutes, or the TV will turn itself Off.
PAGE 96
Captions Menu: Analog and Digital Captions Captions Menu Background Figure 14 Select Captions to perform the functions listed below. On analog channels (Antenna A or Antenna B), broadcasters can send either Standard or Text closed captioning. Standard Closed Captions follow the dialogue of the characters on-screen and display in a small section of the screen. Text Closed Captions often contain information such as weather or news and covers a large portion of the screen.
PAGE 97
Captions Menu: Digital Captions Settings Appearance Background Figure 15 Closed Captions provider selects the Default options when sending digital closed captions. You may, however, select the Custom option to override and customize Closed Captions appearance. These settings do not apply to analog Closed Captioning converted to digital. To make the digital closed captions easier to read, you can choose the background color.
PAGE 98
V-Chip Lock Menu: Passcode V-Chip V-Chip allows you to Block or Allow programs based upon rating signals sent by the broadcasting station. The TV comes from the factory with the V-Chip in the Off setting. You can turn the V-Chip on within the V-Chip Menu or you can use the V-CHIP button on the remote control to conveniently turn the V-Chip on or off. The factory preset is TV-PG for TV ratings or PG for movie ratings, allowing only programs rated TV-PG/PG or lower.
PAGE 99
V-Chip Lock Menu: V-Chip Definitions V-Chip Signal Information When provided by the broadcaster, V-Chip ratings can be used to control which programs can be viewed or will be blocked. When V-Chip ratings are sent, you will see the ratings when you change the channel or when you press the INFO button on the remote control. Both TV and Movie ratings will display. TV ratings apply to programs and movies developed for TV and may have supplemental blocking by content categories.
PAGE 100
V-Chip Lock Menu: Lock By Time and Front Button Lock Lock By Time Front Button Lock Figure 19 Select Lock by Time to set the specific hours that the entire TV will be locked. During the Lock Time, you must use your passcode to view the TV. 1. Press ADJUST or to select ON or OFF then use ADJUST to move to the “Lock Time” option box. 2. Press ADJUST or to select Lock Time. 3. Press ADJUST start. or to select the time the lock will 4. Press ADJUST box. 5. Press ADJUST stop.
PAGE 101
A/V Settings Menu: Memory Reset, Settings, Video Mute, Black Enhancement, TV Speakers, Audio 2 Out A/V Memory Reset A/V Memory Reset allows you to select the device which will have the A/V Settings returned to the original factory settings. To return a device’s memory to the original factory settings, select the device and then press ENT(er). Audio/Video Settings Figure 21 Each device has its own A/V memory.
PAGE 102
A/V Setting Descriptions: Audio NOTE: A slider will display on-screen for most settings. When the slider is displayed it has a numeric value, where 63 is the maximum, 31 is the mid-point and 0 is the minimum. Audio Settings NOTE: The effects of the Audio Settings of Bass, Treble, Balance and Surround affect the sound heard through the TV speakers only. ◊ Bass Enhances or reduces low-pitch sound. ◊ Treble Enhances or reduces high-pitch sound.
PAGE 103
A/V Setting Descriptions: Video NOTE: A slider will display on-screen for most settings. When the slider is displayed it has a numeric value, where 63 is the maximum, 31 is the mid-point and 0 is the minimum. Video Settings for the Television ◊ Contrast Adjusts the white-to-black level. Low contrast shows a variety of shades in darker images, while high contrast shows darker images more uniformly black and makes colors appear more vibrant. In most home lighting situations, a medium contrast looks best.
PAGE 104
Advanced Menu: Color Balance, Reset Color, Lamp Status Advanced Menu Auto Color Correction Figure 22 Set the Color Balance option to Automatic to optimize color automatically and continuously. Both PerfectColor and Reset Color options are grayed out and unavailable when Automatic is selected as the Color Balance option. Reset Color Select to reset the PerfectColor settings. Each active input can be individually reset. Figure 22. Advanced Menu .
PAGE 105
Chapter . . . Special Features 5 NetCommand® Controlled Peer-to-Peer Connections.............. 58 NetCommand Remote Control Buttons: Device Menu, Guide.... 59 Recording on a Net Command Traditional VCR, A/V Disc Search, Track List Screen ............................................. 60 Memory Card Playback ................................................................. 61 PC Viewing...................................................................................... 63 Device Menu with NetCommand® ...
PAGE 106
NetCommand® Controlled Peer-to-Peer Connections What is a Peer-to-Peer Connection? Figure 1 A peer-to-peer connection allows the IEEE 1394 devices in your TV network to talk to each other without the further need of TV intervention once the peer-to-peer connection is established. For example, the TV can setup a connection for an A/VDisc or DVCR that sends a recorded program to an IEEE 1394 monitor in another room. NetCommand will establish the connection between the two devices.
PAGE 107
NetCommand Remote Control Buttons: Device Menu, Guide Device Menu Guide While watching a NetCommand compatible traditional IR controlled or an IEEE 1394 device, press DEVICE MENU once or twice to display the menu for that device. • For NetCommand compatible satellite receivers and some cable boxes, GUIDE will display the on-screen programming guide for the receiver or cable box. Press ADJUST , , or and ENT(er) to navigate the displayed Guide.
PAGE 108
Recording on a NetCommand® Traditional VCR, A/V Disc Search, Track List Screen Recording on a NetCommand Traditional VCR Pressing REC (record) button will function the same way as pressing the record button on the VCR’s remote control or front panel. To record directly from antenna or cable: 1. Press DEVICE on the TV’s remote to display the Device Selection menu. Highlight the traditional VCR and press POWER to turn on the VCR.
PAGE 109
Memory Card Playback Warning: Some memory cards available on the market are not properly certified for use by the Card Reader. If you experience problems with the reading of your file, please transfer your files to a card from a different manufacturer. Memory Card Slots Remote Control Buttons for Controlling the Playback 1. Insert a card into a matching card slot on the front of the TV. Be sure to use the correct card slot. Card 1 will accept MultiMediaCard™ and SD Memory Card.
PAGE 110
Memory Card Playback, continued For MP3 or WMA7 Audio Menu: Figure 5 1. Press GUIDE on the remote to display the Playlist. 2. Using ADJUST or to move the highlight to different tracks (CH up/down will change pages of the Playlist). 3. Press PLAY to begin playback. The Playlist menu will be taken down. An asterisk (*) will be next to the song currently playing. NOTE: During MP3 or WMA7 audio playback, audio from the cards will be sent to the A/V Receiver as analog audio. Digital out is not available.
PAGE 111
PC Viewing PC Input Figure 7 To display your PC screen on the TV, first, connect it to the TV’s back panel (see book 1). You will then be able to select it through the Device Selection Menu. For the correct screen resolution (pixels), use the PC’s Control Panel settings. Your Mitsubishi TV can display resolutions from standard VGA (640 x 480) through PC 1080p (1920 x 1080). See Appendix B, in this book for more screen resolutions. The instructions below are for most PC’s. 1.
PAGE 112
Device Menu with Net Command® NetCommand Compatible Traditional Devices (Analog) When Device Selection Menu is Displayed and the Device is Highlighted (Yellow Outline) REMOTE CONTROL BUTTON A/VReceiver VCR DVD Cable Box/DBS POWER Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) Power On/Off (toggle) DEVICE MENU n/a n/a n/a n/a GUIDE Changes between Digital and Analog audio Changes VCR inputs n/a Changes antenna inputs (RCA model DTC-100 only) FORMAT n/a n/a Changes
PAGE 113
Device Menu with Net Command®, continued Remote Control Button When Net Command® Compatible Traditional Device is Viewed or Played A/V Receiver VCR DVD Cable/DBS CH up/down n/a Channel up/down Skip Forward/Backwards Chapter or Track Channel up/down Page up/down when guide showing VOL up/down Volume Up/Down n/a n/a n/a MUTE Mute On/Off n/a n/a n/a n/a number functions number functions number functions QV n/a n/a n/a Last Channel Recall DEVICE Menu n/a 1st press Transport Menu, 2
PAGE 114
Software Updates From time to time, Mitsubishi may offer software updates to expand the features or operation of this TV. When these updates are available they will be announced on our web site, Mitsubishi-tv.com. If you return your Owner’s registration card, with your model and serial number, you may receive written notification of available software updates.
PAGE 115
Operation of PIP and POP (PIP not available with Ant-DTV) Picture-In-Picture (PIP) and Picture-Outside-Picture (POP) features allow you to view programming in different ways. While watching the main TV picture, you can display programs from other channels and other inputs. You can display a single PIP, side-by-side pictures, three POPs, or nine POPs Activating the PIP and POP. For PC’s, Side-bySide is the only available PIP/POP option. Press PIP/POP to activate the PIP/POP option.
PAGE 116
Display Formats This is a wide screen TV (also known as a 16:9 TV). This shape reflects the new types of images available from HDTV and many DVDs. There are still many older style narrow screen images (called 4:3 aspect ratio) you will encounter. While there will never be a perfect solution for displaying a narrow image on a wide screen, Mitsubishi offers several display formats to choose from. Press FORMAT on the TV remote control to cycle through the available display formats.
PAGE 117
TV Display Formats ��
PAGE 118
PC Display Formats Signal Format Original Pixel Count VGA 640 x 480 Standard �� SVGA PC 720p WXGA �� 1280 x 720 1365 x 768 �� 1920 x 1080 �� 70 �� Zoom 4 (Zoom 2) 1280 x 1024 �� PC1080p �� Zoom 3 1024 x 768 �� SXGA �� Zoom 2
PAGE 119
Appendix A: Bypassing the V-Chip Lock: Lock Bypass Instructions Have Been Filed for Future Reference Bypassing the V-Chip Lock After you set the lock, you need your passcode to view a V-Chip locked program, view the locked TV, cancel the lock, or enter the V-Chip Lock menus. If you forget your passcode, you can view the locked TV without entering your passcode. This is done by pressing the number 9 and QV buttons on the TV remote control at the same time, when your passcode is requested.
PAGE 120
This page intentionally blank 72
PAGE 121
Appendix B: Input Connection Compatibility Component-1 and Component-2 Inputs These inputs are compatible with component video signals from standard DVD players and other equipment sending a standard NTSC component video signal (480i). These inputs are also compatible with newer DVD players sending 480p and are compatible with signals from digital TV receivers that send 720p and/or 1080i component video signals. PC Input This input will accommodate most computers capable of supporting a VGA monitor.
PAGE 122
Appendix C:Remote Control Programming Codes To Program the Remote to Control Other Brands of Audio and Video Products 1. Move the slide switch at the top of the remote to the product you want to control. 2. Press and hold the POWER button on the remote control. 3. Enter the first three digit code listed for your equipment, and then release the POWER button on the remote control. 4. Point the remote control at the equipment and press the POWER button.
PAGE 123
Appendix C: Remote Control Programming Codes DVD Players Mitsubishi 003 Aiwa 261, 274 Apex 266, 283 Bose 286 Denon 250, 273 Ferguson 251 GE/RCA/Proscan 51, 256 Harman Kardon 282, 288 Hitachi 270 JVC 257 Kenwood 271, 289 Mintek 285 Next Base 284 Normande 251 Onkyo 267, 280 Oritron 263, 268 Paite 262 Panasonic 250 Philips/Magnavox 258, 253, 272, 290 Pioneer 252 Saba 251 Sampo 263 Samsung 261 Sanyo 275 Sharp 260 SMC 275 Sylvania 264 Sony 254, 278, 279 Thompson 251 Toshiba 253, 287 Venturer 281 Vialta 277 Wave
PAGE 124
Appendix C: Remote Control Programming Codes After entering the correct codes in each position of the remote control, use the slide switch to select which product will respond when an operational button is pressed. If the TV position has not been programmed to control NetCommand and you enter a code from the A/V Receiver chart while the slide switch is set to TV, the volume and mute functions change to match the A/V receiver. This is useful when using an A/V Receiver with the TV all the time.
PAGE 125
Appendix C: Remote Control Programming Codes When your remote control has been programmed to operate another manufacturer’s product, the function performed on each layer can vary.
PAGE 126
Appendix D: On Screen Information Displays When you turn on the TV, change Devices, change Channels or when you press the INFO button on the remote control the TV will display the current status. Below are the most common displays; please note that seldom or never do all of the different status indicators appear at the same time. Analog Antenna or Devices 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
PAGE 127
Appendix E: NetCommand® Specialized Device Keys A/V CABLE RECEIVER or DBS VCR DVD LEARNING SCREEN CHECKBOX NAME Function Name on TV Remote X X X X Power* Power On or Power On/Off POWER** X X X X Power (Off)* Power Off POWER** X Volume Up Volume Up VOL X Volume Down Volume Down VOL X Mute Mute MUTE X Analog to Digital* Analog/Digital Switch GUIDE** X Digital to Analog* Digital/Analog Switch GUIDE** X Input (1-7) AVR Input Select Automatic (when device is selected) X
PAGE 128
Problem Possible Solution 1. The TV remote control does not work. • Check that the batteries are installed correctly. • Check that the selected switch is set to “TV”. • Be no further than 20 feet from the TV when using the remote control. • Program the remote control to operate the TV (Appendix C). 2. The TV takes several seconds to respond. • It is normal for digital channels to take longer to tune in. • Press ENT(er) after a channel number to avoid delays. • Use the three digit number, i.
PAGE 129
Problem Possible Solution 18. The sound does not match the screen picture. • NetCommand® is setup incorrectly. • The TV’s “Listen to:” setting may be set to SAP. • If using stereo or A/V receiver speakers, check their input selection. • If using stereo or A/V receiver, check that AUDIO 2 of MONITOR OUTPUT on TV’s back panel is connected to the A/V receiver and AUDIO 2 is the setting in NetCommand. 19. You cannot see a picture when playing a VHS tape.
PAGE 130
Problem Possible Solution 30. Cannot see the A/V Receiver menu. • The A/V Receiver is not connected to any input of the TV. To check the A/V Receiver menu temporarily plug into an unused input of the TV. Then select Review from the Setup Menu, turn the input On to view the A/V Receiver menu. 31. Screen is black when trying to view Antenna DTV or IEEE 1394 device. • The PerfectColor™ color balance has been incorrectly set. Use the Advanced menu to reset the color balance. 32.
PAGE 131
Problem Possible Solution 42. All IEEE 1394 devices disappear. • When connecting the devices, there must always be a device at the end. The connected devices must not be in a loop that returns to the TV. • Disconnect all the cables and devices from the TV. Replace them one by one to locate the problem device or cable. • Use System Reset (front control panel). 43. Cannot rediscover a deleted IEEE 1394 device • The device has been disconnected. Plug it in.
PAGE 132
Using The System Reset Button If the TV doesn’t respond to either the remote control or the front panel controls or will not power off, press the SYSTEM RESET button on the front panel with a pointed item such as the point of a ball point pen or end tip of a paperclip. The TV will turn off and the green led will flash quickly for about one minute. When the green led stops flashing, you may turn on the TV again.
PAGE 133
Notes 85
PAGE 134
Index A E A/V Disc Search 60 A/V Receiver, adding in NetCommand Edit NetCommand®, Adding an A/V Receiver 23-25 Edit NetCommand® Adding A/V Receiver 23-25 Device 26-29 Changing Devices 30 Deleting Devices 30 Menu screen 43 Edit Menu 23-25 Initial Setup 21 A/V Settings Menu 42, 53 Descriptions Audio 54 Video 55 Accessories for TV 8 Advanced Menu 42, 56 Antenna Menu 42, 44-45 Audio/Video Menu 42, 53 Audio Setting Description 54 Audio 2 Out 53 Automatically Adding IEEE 1394 Devices 34 B Black Enhancement
PAGE 135
NetCommand® Adding Devices, 20, 23- 29 Changing Devices 30 Deleting Devices 30 Editing 23-30 Initial Setup 19, 21-22 Peer-to-Peer Connections 58 Recording 39 Remote Control Buttons 16, 18, 59 Specialized Device Keys 79 Transport Menu 37, 43 TV Accessories 8 Display Formats 69 Speakers 53 V V-Chip Lock Menu 42, 50-52 Entry 50 Front Button Lock 52 Lock By Time 52 Passcode 50 Rating Definitions 51 Signal Information 51 Start, Stop Time 50 O On Screen Information Displays 78 Operation of PIP and POP 67 P PC
PAGE 136
Notes 88
PAGE 137
MITSUBISHI LCoS PROJECTION TELEVISION LIMITED WARRANTY MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. (“MDEA”) warrants to the original purchaser of this television that if purchased from an authorized MITSUBISHI Audio/Video Dealer, should it prove defective by reason of improper workmanship and/or material: a. Parts. The diffusion (i.e. front picture) screen and/or the Diamond Shield™ is warranted against defects in materials and workmanship for a period of 30 days.
PAGE 138
MITSUBISHI TV SOFTWARE END-USER LICENSE AGREEMENT FOR EMBEDDED SOFTWARE IMPORTANT – READ CAREFULLY: This License Agreement is a legal agreement between you (either an individual or an entity) and Mitsubishi Digital Electronics America, Inc. (MDEA) for all software preinstalled and/or provided along with this television (“Software”). By utilizing this television and Software, you agree to be bound by the terms of this License Agreement.
PAGE 139
Demo Mode This TV has a demo mode for use in a retail store. To turn On/Off, press the following buttons on the remote control in sequence: TV Menu (to display the TV’s menu),Then press: 0, QV, 0 LICENSOR’S SUPPLIERS DO NOT MAKE OR PASS ON TO END USER OR ANY OTHER THIRD PARTY, ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY OR REPRESENTATION ON BEHALF OF SUCH SUPPLIERS, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
PAGE 140
If you have questions regarding your television, call Consumer Relations at (800) 332-2119, or email us at M D E A s e r v i c e @ b i g s c re e n . m e a . c o m To order replacement or additional remote controls or owner’s guides call (800) 553-7278 or visit our website at w w w.m i t s u b i s h i -t v.c o m © 2003 Mitsubishi Digital Electronics America, Inc. 871D398A10 Designed and Printed in the U.S.