User's Manual

ManualsBrandsMitsumi Electric ManualsElectronicsBluetooth HCI module

Page 1 of 4

WML-C95_User_Manual

User Manual

MITSUMI Bluetooth HCI Module

MODEL WML-C95

The purpose of this manual is to explain correct way how to integrate module WML-C95 to the end product. It

includes procedures that shall assist you to avoid unforeseen problems. This manual presents information that

shows how module and OEM product, where module integrated, complies with regulations in certain regions. Any

modifications, not expressly approved by the manufacturer could void the authority to operate in these regions.

Content

1. General

2. Product Information

3. Federal Communications Commission Interference Statement

4. Industry Canada Statement

1. General

This MITSUMI Bluetooth HCI Module, model WML-C95 has to be installed and used in accordance with the

technical description/installation instructions provided by the manufacturer.

For detail information concerning type approval of this module, please contact the authorized local distributor or

manufacturer.

The system may only be implemented in the configuration that was authorized. Note that any changes or

modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to

operate this equipment.

2. Product Information

WML-C95 is a Bluetooth HCI Module. The specification is shown in the following.

Power Supply VBAT:DC 2.97V to 3.63V (3.3V Typ)

VIO:DC 1.7V to 1.98V (1.8V Typ) or 2.97V to 3.63V (3.3V Typ)

Bluetooth

Version Bluetooth V4.0 BDR/EDR+LE

Carrier Frequency 2.402GHz to 2.480GHz

Output Power 0 dBm (Class 2)

Hopping 1600hops/sec

Modulation Method GFSK, PI/4-DQPSK, 8DPSK

Data rate GFSK: 1Mbps , PI/4-DQPSK: 2Mbps , 8DPSK: 3Mbps

Host interface UART, PCM (I2C)

Summary of content (4 pages)

PAGE 1
Page 1 of 4 WML-C95_User_Manual User Manual MITSUMI Bluetooth HCI Module MODEL WML-C95 The purpose of this manual is to explain correct way how to integrate module WML-C95 to the end product. It includes procedures that shall assist you to avoid unforeseen problems. This manual presents information that shows how module and OEM product, where module integrated, complies with regulations in certain regions.
PAGE 2
Page 2 of 4 WML-C95_User_Manual 3. Federal Communications Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 3
Page 3 of 4 WML-C95_User_Manual End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: EW4C95”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.
PAGE 4
Page 4 of 4 WML-C95_User_Manual Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires.