User's Manual

ManualsBrandsMitsumi Electric ManualsElectronics802.11bgn WLAN Module

User Manual

802.11bgn WLAN MODULE

MODEL DWM-W069

The purpose of this manual is to explain correct way how to integrate module

DWM-W069 to the end product. It includes procedures that shall assist you to avoid

unforeseen problems. This manual presents information that shows how module

and OEM product, where module integrated, complies with regulations in certain

regions. Any modifications, not expressly approved by the manufacturer could void

the authority to operate in these regions.

The 802.11bgn WLAN MODULE, model DWM-W069 has to be installed and used

in accordance with the technical description/installation instructions provided by the

manufacturer.

For detail information concerning type approval of this module (e.g. where this

module is already pre-approved) please contact the authorized local distributor or

the manufacturer.

The system may only be implemented in the configuration that was authorized.

Note that any changes or modifications to this equipment not expressly approved

by the manufacturer could void the user’s authority to operate this equipment.

Summary of content (9 pages)

PAGE 1
User Manual 802.11bgn WLAN MODULE MODEL DWM-W069 The purpose of this manual is to explain correct way how to integrate module DWM-W069 to the end product. It includes procedures that shall assist you to avoid unforeseen problems. This manual presents information that shows how module and OEM product, where module integrated, complies with regulations in certain regions. Any modifications, not expressly approved by the manufacturer could void the authority to operate in these regions. The 802.
PAGE 2
Regulatory Information Operational Information Wireless Interoperability The end product integrating this module is designed to be interoperable with any wireless LAN product that is based on direct sequence spread spectrum (DSSS) and orthogonal frequency division multiplexing (OFDM) radio technology and to comply with the following standards. ･IEEE Std 802.11b Standard on 2.4GHz Wireless LAN ･IEEE Std 802.11g Standard on 2.4GHz Wireless LAN ･IEEE Std 802.11n Standard on 2.
PAGE 3
USA-Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
PAGE 4
other antenna or transmitter. Canada-Industry Canada (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of this device.
PAGE 5
Caution: Exposure to Radio Frequency Radiation. To comply with IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
PAGE 6
Europe-EU Declaration of Conformity and Restrictions Hereby, MITSUMI declares that this Mitsumi 802.11bgn WLAN MODULE DWM-W069 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. This equipment is marked with the symbol and can be used throughout the European community.
PAGE 7
To comply with RF exposure compliance requirements, a separation distance of at least 2.2 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter, without further RF Exposure evaluation.
PAGE 8
NCC Warning Statement 低功率電波輻性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。模組認證合格標簽 (ID): “ CCXXxxLPyyyZz＂如果使用本模組之平台,無法在外部看見審驗合格標籤時,應在該平台的外部明顯標示 “內含射頻模 CCXXxxLPyyyZz” .
PAGE 9
Information for OEM integrator Label for end product must include is " Contains XXXyyyLPDzzzz-x¨