Instructions / Assembly

DEMI
H476701S, H476701M, H476701L
INSTALLATION INSTRUCTIONS
www.hvlgroup.com
Questions? We're here to help!
Contact us at [e-mail]
9
2
1
10
11
12
ITEM
DESCRIPTION
PART NUMBER
1 FIXTURE ASSEMBLY
FAS-H476701S,701M,701L
2
SCREW COLLAR
CPY-H476701S
3
CANOPY
HDW-H476701S
4 1/4 NIPPLE HDW-H476701S
5
MOUNTING PLATE HDW-H476701S
6 WIRE STRAIN RELIEF HDW-H476701S
7
MOUNTING SCREW
HDW-H476701S
8 GROUND SCREW HDW-H476701S
9
WIRE NUT
HDW-H476701S
10 SHADE
SHD-H476701S,701M,701L
11 SOCKET RING RNG-HL476101
12
BULB
NOT INCLUDED
3
4
7
5
8
6
FIXTURE INSTALLATION
1. Feed the FIXTURE ASSEMBLY WIRE (1) through the SCREW COLLAR (2), CANOPY (3), NIPPLE(4),
MOUNTING PLATE (5), and STRAIN RELIEF WASHER (6) until you desired hanging height is met.
2. Tie an overhand knot to secure the wire in place above the NIPPLE (4). Trim off excess wire minimum 6"
beyond the knot and Strip each wire end 5/8"
3. Attach the MOUNTING PLATE (5) to the Junction box using the MOUNTING SCREWS (7). This fixture is
designed to be mounted to a standard round or octagon junction box. The junction box must be securely
mounted to the structure of the building.
4. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the
GROUND SCREW (8) on the MOUNTING PLATE (5). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!
FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
5. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together
with an approved fastener (WIRE NUT) (9). Starting 1" below the fastener, tightly wrap the connection with
electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED
WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
6. Connect the black fixture leads to the hot (Generally black) wire in the outlet box. Fasten the joined wires same
as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD
RESULT IN SERIOUS INJURY OR DEATH!
7. Push the wires back into the junction box. Lift up the CANOPY (3) up to the ceiling, and screw the SCREW
COLLAR (2) onto the NIPPLE (4).
8. Lift the SHADE (10) up to the FIXTURE ASSEMBLY (1) and secure using the SCKET RING (11).
9. Screw the BULB (12) up into the SOCKET of the fixture THIS FIXTURE IS RATED FOR LED 15 WATT LAMP.
DO NOT EXCEED THE RECOMMENDED WATTAGE!
10. Restore power to the outlet at the breaker or fuse box.
WARNING/CAUTION
· DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS
COMPLETELY BEFORE STARTING INSTALLATION.
· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED
FACTORY TRAINED TECHNICIAN.
· CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS
AFTER USE.
· REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE
CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR
TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.
· DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE
TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT
FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL
ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.
· PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS
HUDSON VALLEY LIGHTING