MK-377 SERIES TILE SAW OWNER’S MANUAL & OPERATING INSTRUCTIONS CAUTION: Read all safety and operating instructions before using this equipment Enter the Serial Number of your new saw in the space below. The Serial Number is located on the left side of the blade guard. SERIAL NUMBER: NOTE: For your (1) one year warranty to be effective, complete the warranty card (including the Serial Number and mail it in as soon as possible.
INTRODUCTION We at MK Diamond want to congratulate you on selecting the MK-377 Tile Saw. We are certain that you will be pleased with your purchase. MK Diamond takes pride in producing the finest products in the industry. Operated correctly, your MK-377 should provide you with years of quality service. In order to help you, we have included this manual. This owner’s manual contains information necessary to operate and maintain your MK-377 safely and correctly.
TABLE OF CONTENTS SAFETY: Safety Messages Damage Prevention Message General Safety Precautions and Hazard Symbols California Proposition 65 Message Electrical Requirements and Grounding Instructions Tile Saw Specific Warnings Product Specifications Page 4 4 4 4 6 7 9 9 EXPLODED VIEW AND PARTS LIST Exploded View Parts List 10 11 THEORY Theory of Diamond Saws 13 ACCESSORIES Accessories 14 ORDERING and RETURN INSTRUCTIONS Ordering Information Return Material Policy Packaging Instructions Authorized Ser
SAFETY Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to you or others. Failure to read and follow these instructions could also result in damage and/or reduced equipment life. SAFETY MESSAGES: Safety messages inform the user about potential hazards that could lead to injury, death and/or equipment damage.
SAFETY USE THE PROPER EXTENSION CORD. If using an extension cord make sure it is in good condition first. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage that will result in a loss of power and overheating. TABLE 1, Page 8 shows the correct AWG size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage.
SAFETY Hazard Symbols: ELECTRICAL SHOCK! Never touch electrical wires or components while the motor is running. Exposed, frayed or worn electrical motor wiring can be sources of electrical shock that could cause severe injury or burns. ACCIDENTAL STARTS! on Before plugging the equipment into an electrical outlet, be sure the ON/OFF switch is in the OFF position to prevent accidental starting. Unplug the power tool before performing any service operation.
SAFETY ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS: In order to prevent potential electrical shock and injury, the following electrical safety precautions and symbols should be followed at all times! In case of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug.
SAFETY Power Cord To avoid the possibility of the appliance plug or receptacle getting wet, position the saw to one side of a wall mounted receptacle. This will prevent water from dripping onto the receptacle or plug. A "drip loop," shown in FIGURE 2, should be arranged by the user to properly position the power cord relative to the power source. The "drip loop" is that part of the cord below the level of the receptacle, or Power Tool the connector, if an extension cord is used.
SAFETY TILE SAW SPECIFIC WARNINGS: Wear eye protection. Use splash hood for every operation for which it can be used. Disconnect saw before servicing, when changing cutting blades, and cleaning. Use tool only with smooth edge cutting blades free of openings and grooves. Replace damaged cutting blade before operating. PRODUCT SPECIFICATIONS: The MK-377 is a versatile Tile Saw. Operated and used according to this manual, the MK-377 will provide years of dependable service.
EXPLODED VIEW AND PARTS LIST EXPLODED VIEW: MK-377 Revision March 25, 2003 Page 10
EXPLODED VIEW AND PARTS LIST PARTS LIST: Item A A1 A2 A3 A4* A5* A7 B B1 B2 B3 B4 B5 D1 D2 D3 Description Accessories Wrench, Blade Nut, 15/16 Boxed End Wrench, Blade Shaft, 11/16 Open End Blade, 7 Dia X 5/8 arbor MK-170 Owner’s Manual, 377 Warranty Card Assembly, Rip Guide w/ Screw, ¼ –20 x ¾ Thumb Assembly, Blade Guard, 7” Guard, 7” Blade Elbow, 1/8 MNPT X 1/4 BARB 90° Brass Knob, Davies Washer, 5/16 SAE Flat Wing nut, 5/16-18 Nylock Frame Pan, Water Cord Clip, 1/4 Push Mount Qty 1 1 1 1 1 1 1 Part #
EXPLODED VIEW AND PARTS LIST K K1 K2 K3 K4 K5 Assembly, Roller Wheel, Double Bracket, Roller Wheel Wheel, Roller Screw, 1/4-20 X 1 1/2 Hex Head Cap Washer, 1/4 SAE Flat Nut, 1/4-20 Hex 1 1 2 2 2 2 156586 156522 151799 151914 151915 151893 L L1 L2 L3 L4 Assembly, Splash Curtain Curtain, Splash Bracket, Splash Curtain Washer, 1/4 SAE Flat Wing screw, 1/4-20 X 1/2 1 1 1 1 1 155901-MK 134841 155901 151915 151888 1 2 2 2 156536 151743 151747 151754 1 1 2’ 1 155987-MK 155987 132951 154394 M1 M2 M3 M4
THEORY THEORY OF DIAMOND BLADES: Diamond blades do not really cut; they grind the material through friction. Diamond crystals, often visible at the leading edge and sides of the rim/segment, remove material by scratching out particles of hard, dense materials, or by knocking out larger particles of loosely bonded abrasive material. This process eventually cracks or fractures the diamond particle, breaking it down into smaller pieces.
ACCESSORIES ACCESSORIES: ITEM 1. NUMBER DESCRIPTION 139295 MK-200, 7 x 5/8 Arbor 139311 MK-215, 7 x 5/8 Arbor 153293 MK-315, 7 x 5/8 Arbor 134569-MK Dual 45° Flat Angle Guide 134585-MK 45° Bullnose Miter 134569-MK 90° Protractor 152792 Dressing Stone 152610 Ground Fault Circuit Interrupter 155953 Stand 2. 3. 4. 5. 6. 7. 8. 9.
ORDERING and RETURN INFORMATION ORDERING INFORMATION: You may order MK Diamond products through your local MK Diamond distributor or, you may order direct from MK Diamond. NOTE: There is a $25.00 minimum order when ordering direct from MK Diamond. All purchases must be made using VISA or MasterCard.
MK-377 SERIES TILE SAW OWNER’S MANUAL & OPERATING INSTRUCTIONS CALIFORNIA PROPOSITION 65 MESSAGE: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contain chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm.