www.mkdiamond.com MK-101 PRO24 TILE SAW OWNER’S MANUAL PARTS LIST & OPERATING INSTRUCTIONS MK-101 Pro24 Revision 300 03.2013 Manual Part No. 158808 Caution: Read all safety and operating instructions before using this equipment. This owners manual MUST accompany the equipment at all times.
INTRODUCTION Congratulations on your purchase of a MK-101 Pro24 Tile Saw. We are certain that you will be pleased with your purchase. MK Diamond takes pride in producing the finest construction power tools and diamond blades in the industry. Operated correctly, your MK-101 Pro24 should provide you with years of service. In order to help you, we have included this manual. This owners manual contains information necessary to operate and maintain your MK-101 Pro24 Tile Saw safely and correctly.
TABLE OF CONTENTS SAFETY Safety Messages Damage Prevention Message General Safety Precautions California Proposition 65 Message Electrical Requirements and Grounding Instructions Electric Motor Safety Safety Label Locations Lockout Product Specifications Page 4 4 4-7 8 9-10 11 12 12 13 ASSEMBLY Unpacking Contents Transport Stand Assembly 14 14 15 15 16-17 SETUP, ADJUSTMENT AND OPERATION Setup Operation Adjustment Cleanup 19-20 21 22-27 28 MAINTENANCE AND TROUBLESHOOTING Maintenance Troubleshooting 29
MK-101 Pro24 SAFETY Read and follow all safety, operating and maintenance instructions. Failure to read and follow these instructions could result in injury or death to you or others. Failure to read and follow these instructions could also result in damage and/or reduced equipment life. Safety warnings and guidelines do not by themselves eliminate danger. They are not substitutes for proper accident prevention procedures and good judgement.
MK-101 Pro24 SAFETY KEEP CHILDREN AWAY All visitors and children should be kept a safe distance from work area. MAKE THE WORKSHOP KID PROOF Make the workshops kid proof by using padlocks, master switches or by removing starter keys. DO NOT FORCE THE TOOL A power tool will do a job better and safer operating at the rate for which it was designed. USE THE RIGHT TOOL DO NOT force a tool or an attachment, to do a job that it was not designed to do.
MK-101 Pro24 SAFETY USE RECOMMENDED ACCESSORIES Consult the owner’s manual for recommended accessories. Using improper accessories may increase the risk of personal or by-stander injury. Unauthorized equipment modifications will void all warranties. Manufacturer does not assume responsibility for any accident due to equipment modifications. ALWAYS ensure that the machine is on level ground before using.
MK-101 Pro24 SAFETY WARNING Diamond Blades improperly used are dangerous. Comply with American National Standards Institute Safety Code, B7.1 and, Occupational Safety and Health Act covering Speed, Safety Guards, Flanges, Mounting Procedures, General Operating Rules, Handling, Storage and General Machine Conditions ELECTRICAL SHOCK NEVER touch electrical wires or components while the engine is running.
MK-101 Pro24 SAFETY SILICA DUST WARNING Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis.
MK-101 Pro24 SAFETY ELECTRICAL REQUIREMENTS AND GROUNDING INSTRUCTIONS In order to prevent potential electrical shock and injury, the following electrical safety precautions and symbols should be followed at all times! WARNING In case of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug.
MK-101 Pro24 SAFETY WARNING The “drip loop” is that part of the cord below the level of the receptacle, or the connector, if an extension cord is used. This method of positioning the cord prevents the travel of water along the power cord and coming in contact with the receptacle. If the plug or receptacle gets wet, DO NOT unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the tool. Then unplug and examine for presence of water in the receptacle.
MK-101 Pro24 SAFETY ELECTRIC MOTOR SAFETY (( For maintenance care and operation of the electric motor, refer to your electric motor instruction booklet furnished with the electric motor. Protect the electric motor from dust as much as possible and keep ON )) ventilating openings clean. Before plugging in the machine, make sure that the outlet voltage is within the voltage marked on the machines's data plate. CAUTION DO NOT spray water on the electric motor. DO NOT touch the plug with wet hands.
MK-101 Pro24 SAFETY SAFETY LABEL LOCATIONS Safety labels contain important safety information. Please read the information contained on each safety label. These labels are considered a permanent part of your saw. If a label comes off or becomes hard to read, contact MK Diamond or your dealer for a replacement. Tile Saws ! CAUTION ! WARNING Receptacle is for water pump only. 125V, .6 amps max.
MK-101 Pro24 PRODUCT SPECIFICATION MK-101 PRO SERIES PRODUCT SPECIFICATIONS The MK-101 Pro24 are versatile Tile Saws. Operated and used according to this manual, the unit will provide years of dependable service. The MK-101 Pro24 is engineered as table top or stand mounted wet tile saw. The saw includes a powerful 120v totally enclosed capacitor start motor with a thermal protective overload. The MK-101 Pro24 includes a powerful 120v or 240v motor. SPECIFICATIONS Specifications for the MK-101 Pro24.
MK-101 Pro24 CONTENTS UNPACKING Your MK-101 has been shipped from the factory thoroughly inspected. Only minimal assembly is required. CAUTION Use proper lifting techniques when lifting the MK-101 Pro24.
MK-101 Pro24 TRANSPORT TRANSPORT 1. The MK-101 weighs approximately one hundred and thirty (130) pounds. 2. Never transport the MK-101 with water in the Water Basin. The MK-101 is designed with a rigid frame and removable Cutting Head. Two people are required to transport the MK-101 with the Cutting Head installed. Remove the Cutting Head if one person is transporting the saw (see Cutting Head Installation Lift Point and Removal in the following section). Lift the saw using the lift points shown.
MK-101 Pro24 ASSEMBLY ASSEMBLY Follow the assembly instructions to prepare your MK-101 for operation. Cutting Head Installation NOTE: If the cutting head is installed, go to the next step. (A) Align Cutting Head rear Pivot Hole to the Post Pivot Shaft and slide onto shaft. (B) Ensure Cutting Head Stop is in upward position. (C) Install the Cutting Head onto the Post Pivot Shaft and install the Adjusting Knob.
MK-101 Pro24 ASSEMBLY Diamond Blade Installation NOTE: When installing the Retaining Nut, do not “cross-thread” and DO NOT over tighten. Shaft Lock Pushbutton (A) Position Movable Cutting Table to the front of the saw and raise the Blade Guard by loosening the wingnut. (B) Locate the Shaft Lock push button on the underside of the Cutting Head. (C) Depress and hold the Shaft Lock pushbutton and remove Retaining Nut and Outer Flange using the Blade Wrench. (D) Install Diamond Blade onto Blade Shaft.
MK-101 Pro24 ASSEMBLY Adjustable Cutting Guide Installation NOTE: The Adjustable Cutting Guide can be used on either side of the Diamond Blade. (A) Place the Adjustable Cutting Guide onto the Movable Cutting Table Ruler/Stop and tighten the retaining thumbscrew. Splash Guard Installation (A) Install the retaining thumbscrew through the washer and Splash Guard then align to the hole found on back of the Blade Guard. (B) Install the Splash Guard onto the Blade Guard.
MK-101 Pro24 SETUP Pre-start Inspection Prior to beginning work, a pre-start inspection of the saw should be performed. (A) Ensure the ON/OFF Switch is in the OFF position. (B) Verify the Movable Cutting Table moves freely. (D) Inspect the Pump Assembly for damage – ensure the cord is free of cracks or cuts. (E) Inspect the MK-101 for damage – ensure the cord is free of cracks or cuts. (C) Inspect the Diamond Blade for damage – verify the blade is correct for the material being cut.
MK-101 Pro24 SETUP WATER PUMP SETUP FOR OPERATION The Water Pump can be setup for operation in two ways, External Water Source or Re-circulation. NOTE: If using a dry blade for operation, DO NOT connect the water pump. EXTERNAL WATER SOURCE This is the preferred method of cooling. (A) Remove the Drain Plug.
MK-101 Pro24 OPERATION SETUP FOR OPERATION CAUTION 1. B efore powering or starting, check for damage that could prevent this equipment from proper operation or performing it’s intended function. Check for binding and proper alignment of moving parts. Check for damaged, broken, or missing parts. 2. Verify the On/Off switch is in the OFF position. 3.
MK-101 Pro24 ADJUSTMENT SET CUTTING DEPTH CAUTION When loosing the Cutting Head Adjusting Knob, the Cutting Head will pivot down unless held. (A) Loosen Cutting Head Adjusting Knob. (B) Set cutting depth approximately 1/4 to 1/2 inch below the surface of the Movable Cutting Table. (C) Tighten the Adjusting Knob. CUTTING STRAIGHT EDGES CAUTION DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed.
MK-101 Pro24 ADJUSTMENT DIAGONAL CUTTING NOTE: To cut diagonal, the Dual 45º Flat Angle Guide (MK Diamond Part No. 134577-MK) should be used. DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for CAUTION which it was designed. (A) Remove the Adjustable Cutting Guide. (B) Position the Dual 45º Flat Angle Guide and tighten the retaining thumbscrew. (D) Verify proper cooling flow on both sides of the blade (See Maintenance Section to increase/decrease flow). (E) Perform the cut.
MK-101 Pro24 ADJUSTMENT 45° MITER CUTTING NOTE: To cut 45º Miters, the 45º Bullnose Miter Guide (MK Diamond Part No. 153201-MK) should be used. CAUTION DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed. (A) Position the 45º Bullnose Miter Guide and tighten the retaining thumbscrew. (B) Position the tile on the 45º Bullnose Miter Guide and the Ruler/Stop. Turn the motor ON. (D) Perform the cut. Turn the motor OFF when work is complete.
MK-101 Pro24 ADJUSTMENT OFF-ANGLE CUTTING NOTE: To cut 45º Miters, the 45º Bullnose Miter Guide (MK Diamond Part No. 153201-MK) should be used. CAUTION DO NOT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed. (A) Place the 90º Protractor on the Ruler/Stop. (D) Position the tile against the 90º Protractor and the Ruler/Stop. Turn the motor ON. (B) Set the desired angle and tighten the thumbscrew.
MK-101 Pro24 ADJUSTMENT ADJUSTING THE CUTTING HEAD NOTE: For larger tiles and maximum cutting length, the cutting head should be in the front pivot hole. CAUTION The Cutting Head is heavy! Care must be used when changing the position of the Cutting Head. (A) Ensure the ON/OFF Switch is in the OFF position. Unplug the GFCI from the power source. (B) Remove the Blade. Remove Adjusting Knob. (D) Install the Cutting Head onto the front pivot hole. (E) Remove the Cutting Head Stop Bolt.
MK-101 Pro24 ADJUSTMENT ADJUSTING THE POST FOR MAXIMUM CUTTING LENGTH CAUTION The Cutting Head and Post are heavy! Use care when changing the position of the Cutting Head. (A) Ensure the ON/OFF Switch is in the OFF position. Unplug the GFCI from the power source. CAUTION (B) Remove Water Basin and Blade. (C) Remove the Cutting Head (See Adjusting the Cutting Head. Hold the Post when removing the Retaining Bolts. (D) Loosen the retaining bolts. (E) Remove the Standoffs and retaining bolts together.
MK-101 Pro24 CLEANUP CLEANUP NOTES: 1. If an external water source was used, steps A through C may be skipped. 2. Dispose of waste water in accordance with applicable Federal, State and Local laws. (A) Clean the Water Pump suction of all debris. CAUTION (C) Run the MK-101 until clear water is seen at the blade cooling ports (Approx. 1 minute). Ensure the saw is disconnected before completing the remainder of the cleanup process. (D) Remove the Water Basin.
MK-101 Pro24 MAINTENANCE NEW MAINTENANCE Perform the following after initial purchase and operation of the MK-101. (A) Check and adjust V-belt tension following first 48 hours of operation (See V-belt Inspection). MAINTENANCE FOLLOWING USE To extend the life of the MK-101, the following procedure should be performed after each use. Lubricate all points listed below with light oils such as, 3 in 1, WD-40, etc. CAUTION Ensure the saw is off and disconnected before performing any maintenance.
MK-101 Pro24 MAINTENANCE MONTHLY MAINTENANCE The following maintenance should be performed Monthly. (A) Remove the Diamond Blade. (B) Lubricate the Outer Flange and Retaining-nut. (C) Lubricate the Arbor Shaft. (D) Verify the Roller Wheel Assembly is tight and in good condition. (E) Verify all motor mounting Bolts are tight. (F) Verify the Motor Adjustment Strap is tight. (G) Remove the Blade Guard. (H) Lubricate the Blade Guard Pivot Shaft.
MK-101 Pro24 (J) Lubricate the Cutting Head Adjustment Knob. MAINTENANCE (K) Lubricate the Cutting Head Adjustment Knob retaining holes. (L) Lubricate the Cutting Head Pivot Shaft. FLOW MAINTENANCE NOTE: If flow to the diamond blade requires adjustment, perform the following actions. (A) Increase cooling flow by releasing the Flow Adjusting Clamp. (B) Reduce cooling flow by Pressing down on the Flow Adjusting Clamp. BLADE DRESSING A diamond blade performs best when it is dressed.
MK-101 Pro24 MAINTENANCE DIAMOND BLADE CHANGE-OUT NOTE: When installing the Retaining Nut, do not “cross-thread” and DO NOT over tighten the retaining nut. (A) Locate the Shaft Lock pushbutton on the underside of the Cutting Head. (B) Remove Retaining Nut and Outer Flange, depress and hold the Shaft Lock pushbutton and loosen. (C) Remove the Diamond Blade. (D) Install the Diamond Blade onto Blade Shaft. (E) Verify the Blade is seated on the Blade Shaft and direction of rotation is correct.
MK-101 Pro24 MAINTENANCE BELT INSPECTION, ADJUSTMENT AND REPLACEMENT The MK-101 is designed with a power transmission belt. In order to ensure the MK-101 operates at peak efficiency, the V-belt should be inspected monthly, and changed if the belt shows damage and/or excessive wear. NOTE: 1. When a new belt is installed, it should be inspected and re-tensioned after the first forty-eight (48) hours of operation. (A) Remove the Diamond Blade. (B) Remove the Cutting Head (See Adjusting the Cutting Head).
MK-101 Pro24 MAINTENANCE (J) Remove the belt. (K) Install the new belt. (L) Verify the V-belt is seated in the grooves of both pulleys. (M) Tighten the Motor Adjustment Strap to remove slack. (N) Check belt tension (proper tension 1/8-inch). (O) Repeat steps M and N until proper belt tension is achieved. (P) Tighten the motor mounting bolts. (Q) Install the Belt Guard.
MK-101 Pro24 TROUBLESHOOTING BLADE WILL NOT CUT PROPERLY: (A) Check for Smoothness or “Glazing” (Dress blade if needed). (B) Check for proper blade rotation. (D) Verify the blade is correct for the material being used. MOVABLE CUTTING TABLE DOES NOT MOVE CORRECTLY (A) Check the Guide Bar and Frame for cleanliness – clean if dirty. (B) Check the Movable Cutting Table Roller Wheels for wear – replace if necessary. 35 (C) Ensure the Blade Core is not bent.
MK-101 Pro24 TROUBLESHOOTING COOLING FLOW (A) Verify the cooling flow Adjusting Clamp is open. If flow exists, go to Step B. (B) Remove the Cooling Transfer Tube from the Blade Guard inlet. Go to Step C. (C) Place Pump into a bucket of water and check flow. If flow exists, go to Step D. (D) Remove the Cooling Transfer Tube and check for flow. If flow exists, refer to water pump manual. (E) Remove the Blade Guard Intake Fitting. Go to Step F. (F) Remove the Cooling Channel cover screws. Go to step G.
MK-101 Pro24 TROUBLESHOOTING BLADE STOPS TURNING (A) Allow the motor to cool and depress motor Overload Reset Switch. If motor does not start, go to Step B. NOTE: (B) Verify all plugs fully installed. Check Ground Fault Circuit Interrupter Verify circuit breaker at least 20 amps - if not, move to 20-amp circuit. Verify circuit breaker is not tripped. If tripped, reset. Check power source voltage is 120V - if not 120V, move to another circuit.
MK-101 Pro24 TROUBLESHOOTING BLADE ALIGNMENT PROCEDURE The Movable Cutting Table of the MK-101 may become misaligned with the Cutting Head of the Tile Saw over time. Should misalignment occur, perform the following steps to realign the Tile Saw. NOTE: If alignment problems are the result of a warped blade, a bent frame or bent support arm, or, if alignment is off by more than 1/8-inch, contact the MK Diamond Service Center – (800) 474-5594 TOOLS NEEDED (A) Combination square (square) 12-inch or greater.
MK-101 Pro24 TROUBLESHOOTING HORIZONTAL ALIGNMENT PROCEDURE The Horizontal alignment will ensure that straight cuts (or Rip Cuts) are made. (A) Position Cutting Head to normal Cut Depth. (B) Move Guide Bar until Blade is centered in Cutting Groove. Tighten rear guide bar retaining bolt. (D) Position Square flat on Movable Cutting Table against Ruler/Stop. Position front of Square against Blade. (E) Move Guide Bar until Square rests evenly across Blade.
MK-101 Pro24 TROUBLESHOOTING 90° ALIGNMENT VERIFICATION 90º-alignment verification ensures the blade cuts tile straight up and down and not at an angle. The Diamond blade must be removed and reinstalled when removing the blade guard. NOTE: If the blade is misaligned following 90º-alignment verification, return the saw to MK Diamond for repair. (A) Remove Blade Guard and water pan. (B) Position Square on Movable Cutting Table against the Diamond Blade.
MK-101 Pro24 EXPLODED VIEW 16 15 1 5 29 2 6 28 4 18 17 9 8 12 7 19 10 14 11 25 27 3 26 20 21 13 24 22 23 MK-101 Pro24 Tile Saw Part# 153243 42
MK-101 Pro24 PARTS LIST MK-101 Pro24 Assembly Part# 153243 Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Description FITTING, PLASTIC, 1/4 FNPT X 1/4 BARB HOSE, VINYL 1/4 X 3/8 (6.
MK-101 Pro24 EXPLODED VIEW & PARTS LIST Frame Assembly Part# 170477 3 7 5 6 1 2 4 8 Item 1 2 3 4 5 6 7 8 Description WASHER, LOC, SPLIT, 3.8 SCREW, SET, SOC, CUPT, 3.8 - 16 X 1/2 SHAFT, 12.
MK-101 Pro24 EXPLODED VIEW & PARTS LIST Table Assembly Part# 160378 11 5 2 3 4 9 1 8 10 2 3 6 4 7 Item 1 2 3 4 5 6 7 8 9 10 11 Description CASTING, 101/990 LNR BRG MT - COM SCREW, HEX HD, 5/16 - 18 X 1 WASHER, LOCK, SPLIT, 5/16 WASHER, FLAT, SAE, 5/16 ASSY, WHEEL BRKT TSAW SPACER, GUIDE BAR COVER, COMMON COVER, 3/4 X 37 GUIDE BAR BAR, 3/4 X 37 LINEAR GUIDE, 101 SCREW, 1/4 - 20 X 5/16 SOCKET HEAD SET CAST, TABLE, PRO24, OVRMLD - COMP TABLE, EXTENSION (COMP) 45 Part # 135855 151743 151747 151754 1
MK-101 Pro24 EXPLODED VIEW & PARTS LIST Assy, Wheel Brkt TSaw Part# 151756 5 2 1 4 3 Item 1 2 3 4 5 Description WHEEL, ROLLER TSAW NUT, HEX, 1/4 - 20 SCREW, HEX HEAD 1/4 - 20 X 1 - 1/2 WASHER, FLAT, SAE, 1/4 BRACKET, ROLLER WHEEL 46 Part # 151799 151893 151914 151915 154021 Qty 1 1 1 1 1
MK-101 Pro24 EXPLODED VIEW & PARTS LIST Cutting Head Part# 158481 INCLUDED WITH ITEM 8 13 7 10 INCLUDED WITH ITEM 8 1 4 9 11 12 8 2 5 2 2 6 3 2 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 5 5 5 3 3 DESCRIPTION KEY, 3/16 SQ X 1 -1/8 WASHER, FLAT, SAE, 1/4 SCREW, HEX HD, 1/4 - 20 X 3/4 ASSY, BLADE GUARD, 101 WASHER, LOCK, SPLIT, 1/4 SCREW, HEX HD TAP, 1/4 - 20 X 1 SCREW, 5/16 - 18 X 3/8 SOCKET HEAD SET ASSY, SUB, CTTG HEAD MK-101 BELT, 6J260 PULLEY, 6J19 X 5.
MK-101 Pro24 EXPLODED VIEW & PARTS LIST Assy, Sub Cutting Head 101 Part# 158191 1 9 10 13 8 11 3 6 14 12 21 2 23 4 20 22 18 17 7 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 15 5 16 19 DESCRIPTION NUT, HEX, 5/16 - 18 FLANGE, OUTER, 2 - 3/8 NUT, HEX, 5/8 18 BEARING, BALL, 17 X 40 X 12MM KEY, 3/16 SQ X 1/ 1/8 WASHER, FLAT, SAE, 3/8 SCREW, HEX HD, 5/16 - 18 X 1 NUT, WING, NYLK, 5/16 - 18 X 1 WASHER, LOCK, SPLIT, 5/16 WASHER, FLAT, SAE, 5/16 STRAP, 1 INCH MOTOR ADJ.
MK-101 Pro24 EXPLODED VIEW & PARTS LIST Motor Part# 160486 2 3 1 ITEM 1 2 3 DESCRIPTION TERMINAL, 16 - 14 AWG X #10 RING MTR, 1.
MK-101 Pro24 EXPLODED VIEW & PARTS LIST Switch Box Part# 161101 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 DESCRIPTION WASHER, #10 SAE FLAT SCREW, PAN HD PHIL 6 - 32 X 5/8 WASHER #10, INTERNAL TEETH BUSHING, SWITCH, 30 AMP BOX, 30A SWITCH (COMP) SWITCH, 30 AMP MOTOR CONTROLLER PLATE, MOUNTING, SWITCH LEVER, ON/OFF, 30 AMP SWITCH GASKET, COVER, 30 AMP SWITCH SEAL, LEVER, 30 AMP SWITCH SCREW, FLAT HD PHIL 6 - 32 X 5/16 SCREW, PAN HD PHIL 10 -24 X 5/16 COVER, 30A SWITCH (COMP) LEVER, ACTUATOR (COMP) STRAI
MK-101 Pro24 EXPLODED VIEW & PARTS LIST Blade Guard Part# 152582 2 1 4 3 ITEM 1 2 3 4 DESCRIPTION SCREW, 5/16 - 18 X 1/2 SOCKET HEAD SET ELBOW, 1/8 MNPT X 1/4 BARB 90DEG TUBE, WATER CASTING, 101 BLD GUARD-DC-COMP 51 Part # 152607 154652 155389 162481 Qty 3 1 2 1
ACCESSORIES ITEM NUMBER DESCRIPTION 137166 MK-200, 10 x 5/8 Arbor Premium grade Diamond Blade for smooth, chip-free cutting on tile. 2. 128074 MK-215, 10 x 5/8 Arbor Supreme grade diamond blade for hard materials 3. 153252 MK-315, 10 x 5/8 Arbor Supreme super hi-rim diamond blade 1. 4. 134577-MK Dual 45° Flat Angle Guide 5. 153201-MK 45° Bullnose Miter 6. 134569-MK 7. 152792 Dressing Stone 8. 152610 Ground Fault Circuit Interrupter 9.
MK-101 Pro24 ORDERING AND RETURN INFORMATION ORDERING INFORMATION You may order MK Diamond products through your local MK Diamond distributor or, you may order direct from MK Diamond. When ordering direct from MK Diamond, please have the following information ready before calling: • The Model Number of the saw • The Serial Number of the saw • Where the saw was purchased and when • The Part Number for the part(s) being ordered • The Part Description for the part(s) being ordered NOTE: There is a $25.
MK-101 Pro24 WARRANTY CONTACT: Please contact MK Diamond Products, Inc. Customer Service Department with any questions you might have regarding distributors, parts or service. Telephone: (800) 421-5830 Fax: (310) 539-5158 E-mail: Customer_Service@MKDiamond.com Customer Service Hours: Monday through Friday, 6AM-4PM PST MK Diamond Products, Inc. 1315 Storm Parkway Torrance, CA 90501 MK DIAMOND PRODUCTS, INC. LIMITED WARRANTY MK DIAMOND PRODUCTS, INC.
MK-101 PRO 24 TILE SAW OWNERS MANUAL & OPERATING INSTRUCTION MK Diamond Products, Inc. 1315 Storm Parkway Torrance, CA 90501 Toll-Free: (800) 845-3729 Phone: (310) 539-2221 Fax: (310) 539-5158 www.mkdiamond.
