To be the Chief Evangelist Ender-3 Pro Series 3D Printer Guide Book [ To make Top-quality 3D printer] ◆ This guide is for the Ender-3 Pro Series of 3D printers. ◆ Select the correct input voltage to match your local mains (230V or 115V) ◆ Because of software/hardware upgrades and model differences, new revisions may not be listed in this guide. ◆ Please plug the power cord into a three−hole power jack. ◆ Detailed instructions for use are available in the TF card. V.2.
Notes 1. Do not use the Printer in any way other than described herein to avoid personal injury or property damage. 2. Do not place the Printer near flammables, explosives or heat sources. It is best to place it in a well- ventilated, low-dust environment. 3. Do not expose the Printer to violent vibration or any unstable environment. This will cause poor print quality. 4. The filaments recommended by the manufacturer are preferred as to avoid clogging in the hot end and/or Printer damage. 5.
Contents 1. 2. 3. 4. Introduction ...………………………............1 Screen Information........……………….........2 Loading Filament......................................3 Bed L e v e l l i n g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5. Software Installation ..………………5 6. Preparing to Print……………………..6 7. Trouble-shooting ……………………..7 Preface Dear consumers, Thank you for choosing our products. For the best experience, please read the instructions before operating the Printer.
1. Introduction 16 7 8 15 9 10 6 11 5 1 1. 2. 3. 4. 1 2 TF Slot and USB Port Control Box Print Surface Control Knob 3 4 5. 6. 7. 8. Display Screen Nozzle Assembly Spool Holder Extruder (E) Stepper 12 9. 10. 11. 12. 13 Power Y Limit Switch Y Stepper Coupling 14 13. 14. 15. 16.
2.
3. Loading Filament 1. Preheat 2. Feeding Method 1 Method 2 Press and hold the extruder lever then insert 1.75mm filament through the small hole of the extruder. Continue feeding until you see filament come out the nozzle. Tip:How to Replace the Filament? 1sCutting filament near the Extruder and slowly feed new filament until they are fed into the new filament. 2sPreheating the nozzle and withdraw the filament quickly and feed the new filament.
4. Bed Levelling 1. Prepare ‹ A u t o Home. Wait for the nozzle to move to the left/front of the platform. 2. Prepare‹Disable Steppers(Close stepper drive,release motor) 4 3 1 2 3.Move the nozzle the front/left leveling screw and adjust the platform height by turning the knob underneath. Use a piece of A4 paper (standard printer paper) to assist with the adjustment, making sure that the nozzle lightly scratches the paper. 4. Complete the adjustment of the screw on all 4 corners. 5.
5. Software Installation 1. Double click to install the software. 2、Double click to open the software. 5 3. Select language→Next→Select your machine→Next→Finish.
6.For the first Printing 1.Slicing Open the software→Load→Select the file→Wait for slicing to finish ,and save the gcode file to TF card. 2.Printing Insert the TF card→ Print → Select the file to be printed.
7.
After- Sales Service Service 1, The printer can be returned within seven days, 15 days replacement, one year warranty, lifetime maintenance. Replacement requirement 1. The appearance of the product is intact, without damage, scratches, smudges, cracks, deformation, etc.; 2. Machine parts, tools and others are complete; 3. Provide a complete and valid purchase invoice and warranty, product number should be the same.
The revision date: May 20,2019 SHENZHEN CREALITY 3D TECHNOLOGY CO.,LTD. 11F & Room 1201,Block 3,JinChengYuan,Tongsheng Community,Dalan g,Longhua District,Shenzhen,China,518109 Official Website: www.creality3d.cn Tel: +86 755-85234565 E-mail: info@creality3d.cn cs@creality3d.