Fidelio T1 User manual Register your product and get support at www.philips.
Contents 1 Important safety instructions 2 Hearing Safety General information 2 2 2 Your Bluetooth True wireless earphones What's in the box Other devices Overview of your True wireless earphones 3 Get started Charge the battery Pair the headphones with your mobile phone 4 Use your headphones Connect the headphones to a Bluetooth device Control ANC (active noise cancelation) Manage your calls and music LED indicator status Voice Assistant 3 3 3 4 5 5 5 7 7 7 8 9 9 5 Factory reset the headset 10
1 Important safety instructions Hearing Safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headset. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts.
2 Your True wireless earphones Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. With this Philips True wireless earphones, you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; • switch between calls and music. Quick start guide Global Warranty Safety leaflet What's in the box Other devices A mobile phone or device (e.g.
Overview of your True wireless earphones 6 Multi-function touch LED indicator (earpieces) LED indicator (factory reset) Factory reset button LED indicator (charging box) USB-C charging slot
3 Get started Charge the battery Note Before you use your earpieces for the first time, place the earpieces in the charging box and charge the battery for 3 hours for optimum battery capacity and lifetime. Use only the original USB-C charging cable to avoid any damage. Finish your call before charging the earpieces, as connecting the earpieces for charging will power the earpieces off. Charging Box Connect one end of the USB cable into the charging box, and another end into the power source.
Pair the earpieces with your Bluetooth device at the fist time Enter the earpieces password “0000” (4 zeros) if prompted. For those Bluetooth devices featuring Bluetooth 3.0 or higher, no need to enter a password. Make sure that the headset is fully charged and powered off.
4 Use your earpieces Control ANC (active noise cancelation) Enable ANC Connect the earpieces to your Bluetooth device Different ANC mode can be toggled via double tap on the right earpiece. • Turn on the Bluetooth function of your Bluetooth device. • Open the top cover from charging box. • ANC function is auto active when put into the ear. Touch the MFB button twice, it will change to Awareness mode. Touch the MFB button twice again, it will turn the ANC function off. The blue LED flashes.
ANC LED indicator status Call control Headphones status Indicator ANC mode is The blue LED will toggled turn on. Task Hang up call Right /Reject call earpiece Power on/off Task Multifunction button Turn the earpieces on. Turn the earpieces off.
Charging Box LED (USB off) Indicator Battery LED indicator on Bluetooth device It will show a battery indicator on Bluetooth device after connected to earpieces. Tip When USB is off, the LED is lit for 30s after case open or closed LED indicator status Headphones Indicator status The earpieces are White LED blink every 5s connected to a Bluetooth device.
5 Reset the earpieces T1 Tap & hold multi-function touch for >25s on each earpiece individually. To pair the headset with a Bluetooth device, Earpiece put back to charging box to power off. Open the top cover from charging box, press and hold the pairing button from charging box back for approximately 3 seconds. Then, turn on the Bluetooth function of your Bluetooth device, select Philips T1.
7 Notice Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com. Remove the integrated battery If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing the headphones.
Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
7 Trademarks Bluetooth The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners. Siri Siri is a trademark of Apple Inc., registered in the U.S. and other countries. Google Google and Google Play are trademarks of Google LLC.
8 Frequently asked questions My Bluetooth headset does not turn on. The battery level is low. Charge the headset. I cannot pair my Bluetooth headset with my Bluetooth device. The Bluetooth is disabled. Enable the Bluetooth feature on your Bluetooth device and turn on the Bluetooth device before you turn on the headset. Pairing does not work. • Put both earpieces into charging box. • Make sure you have disabled the Bluetooth function of any previously connected Bluetooth devices.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. UM_T1_00_EN_V1.
