Headphones 1000 Series TAT1207 User manual Register your product and get support at www.philips.
Contents 1 Important safety instructions 2 Hearing safety General information 2 2 2 Your True wireless earpieces What's in the box Other devices Overview of your True wireless earpieces 3 Get started Charge the battery How to wear Pair the earpieces with your Bluetooth device for the first time Pair the earpieces with another Bluetooth device 4 Use your earpieces Connect the earpieces to your Bluetooth device Power on/off Manage your calls and music Voice Assistant Earpieces/charging box LED indicato
1 Important safety instructions Hearing Safety Danger To avoid hearing damage, limit the time you use headphones at high volume and set the volume to a safe level. The louder the volume, the shorter the safe listening time is. Be sure to observe the following guidelines when using your headphones. • Listen at reasonable volumes for reasonable periods of time. • Be careful not to adjust the volume continuously upwards as your hearing adapts.
2 Your True wireless earphones Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/support. With these Philips True wireless earpieces you can: • Enjoy convenient wireless handsfree calls • Enjoy and control music wirelessly • Switch between calls and music Headphones Series CTN Quick start guide Global Warranty Safety leaflet What's in the box Other devices A mobile phone or device (e.g.
Overview of your True wireless earpieces 1 2 3 4 5 LED indicator (earpieces) Multi-function touch Micphone LED indicator (battery state or charging state) USB-C charging slot 4 EN
3 Get started Charge the battery Charging Box Plug one end of the USB-C cable into the charging box and the other end into the power source. Note Before you use your headphones, place them in the charging box and charge the battery for 2 hours for optimum battery capacity and lifetime. Use only the original USB-C charging cable to avoid any damage. Finish your call before charging. Connecting the earpieces to charge will power them off.
Insert the earpieces 1 Note Check left or right orientation of the earpiece. 2 Insert the earpieces into the ears and twist slightly until a secure fit is achieved. Pair the headphones with your Bluetooth device for the first time 1 2 The following example shows you how to pair the earpieces with your Bluetooth device. 1 Turn on the Bluetooth function of your Bluetooth device, select Philips TAT1207. 2 Enter the earpieces' password “0000” (4 zeros) if prompted.
Pair the earpieces with another Bluetooth device If you want to pair another Bluetooth device with the earpieces, just put them into pairing mode, (press button on box for 3 seconds with both earpieces inside and the cover open), then discover the second device as per normal pairing. Note The earpieces store 4 devices in the memory. If you try to pair more than 4 devices, the earliest paired device is replaced by the new one.
4 Use your earpieces Connect the earpieces to your Bluetooth device 1 Turn on the Bluetooth function of your Bluetooth device. 2 Open the charging box cover. The blue LED flashes The earpieces will search the last connected Bluetooth device and reconnect to it automatically.
Charging box LED indicator status Voice Assistant Task Button Operation Trigger Voice (Siri/Google) Assistant Left earpiece Tap and hold for 2 seconds Stop Voice Assistant Left earpiece Single Tap Earpieces LED indicator status Earpieces status Indicator The earpieces are connected to a Bluetooth device The earpieces are ready for pairing White LED blinks every 5 seconds The earpieces are on but not connected to a Bluetooth device The LED flashes blue and white alternately White LED blinks ev
5 Reset the earpieces If you encounter any pairing or connection issue, you can follow the following procedure to reset your earpieces to factory default value. 1 2 3 4 5 6 On your Bluetooth device, go to the Bluetooth menu and remove Philips TAT1207 from the device list. Turn off the Bluetooth function of your Bluetooth device. Return earpieces to charging box and open the lid. Press button on box twice. Follow steps in “Use your earpiecesconnect the earpieces to your Bluetooth device.
7 Notice Declaration of conformity Hereby, MMD Hong Kong Holding Limited declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. You can find the Declaration of Conformity on www.p4c.philips.com. Remove the integrated battery If there is no collection/recycling system for electronic products in your country, you can protect the environment by removing and recycling the battery before disposing of the earpieces.
Compliance with EMF This product complies with all applicable standards and regulations regarding exposure to electromagnetic fields. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
8 Trademarks Bluetooth The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by MMD Hong Kong Holding Limited is under license. Other trademarks and trade names are those of their respective owners. Siri Siri is a trademark of Apple Inc., registered in the U.S. and other countries. Google Google and Google Play are trademarks of Google LLC.
9 Frequently asked questions My Bluetooth earpieces are connected to a Bluetooth stereo-enabled mobile phone, but music only plays on the mobile phone speaker. Refer to the user manual of your mobile phone. Select to listen to music through the earpieces. My Bluetooth earpieces do not turn on. The battery level is low. Charge the earpieces. The audio quality is poor and a crackling noise can be heard. • The Bluetooth device is out of range.
2021 © MMD Hong Kong Holding Limited. All rights reserved. Specifications are subject to change without notice. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product.