PLEASE KEEP THE PACKAGING 0 To ensure safe transit, your MoFi turntable must be properly repackaged using the original packaging materials (boxes, inserts, etc.). Instructions are available from your dealer or can be found at mofielectronics.com. FUSE INFORMATION 0 Before changing the fuse, unplug the power cord. Instructions for Changing the Fuse Rotate t he fuse head coun terclockwise with 3 flat 5mm screwdriver. remove fuse, and change if needed .
ATTENTION 0 For sonic reasons, we use a specially formulated material in our platters. Some abnormalities and material marks are normal and do not affect the performance of the platter or turntable. 0 Due to very tight tolerance in the platter bearing system, it may take up to several hours for the platter to settle into final position. Thank you for your patience during this process.
ELECTRONICS
a ndg 7 4 2. ) @~ . '81' '• .
0 IKeap1styl1 us, guard l'n place durlng1in1:t1Hati 0 1n 1 'l a1prevent d,a1 mage t,o 1 1 1 1 'tih 1 naadl· 1. Co nect the four heads.heU I ,a ds. making sure the color.-coated I -ads match 'the corresponding col or,,, 1 coded in's. 2~CarefuHy mo unt car· ridge 1 to he headshelt Let nut rest aga~nst cartridge body to al low hread o catch. Tigh n sere ·~s, leaving1 the ability to make slight adjustments.
I . Car fully erno e s ylus g • , al need r a . n ppro_1 _ r c · 1ng a r,c o 2g. 4 . Using the Mobil ideli y GEO-Disc or othe I gnm nt tool. se o e - I e · h y d. st1n c r 1d so tylus tip si s ri h on the buUsey ile tne c: ntile er is p r llel with the Ii ,e h sec s ·he e ca ridg1 ouble-chec n e er s and ou . rk. our urntable allo s, check VTA azimut , and an ·1-sk Do ble-c eek ov rha g/ S he rackin orce to 18 2.2 . W reco,m end g.
US,. G n rm' r cue n m Cl . n ·y our cord b far e ch pl y a , val1 un . ry cle r com nd LP lus Cle S y r.
StudioTracker UltraTracker MasterTracker Type Dual Magnet (MM) Stereo Dual Magnet (MM) Stereo Dual Magnet (MM) Stereo Weight 6 4g 9.7g 9.7g Tracking Forc0 1 8 - 2.2g 1.8 - 2.2g 1.8 - 2.2g Impedance 47kOhm 47kOhrn 47kOhm Capacitance l00pF l00pF lOOpF Frequency Re5ponse ?.0-20.000Hz 20-25.000Hz 20-25,000Hz Stylus Ellrptrcal Nude Elliptical M1cro-L1ne Output Voltage 3 Sn1V 3.
ELECTRONICS www.mofielectronics.com ,1 M, •\ ,,,:aqc h.
ELECTRONICS
' 0 IN THE BOX 1. StudioDeckT" Turntable fS. Power Cord 2. Dustcover 7. Counterweight J . Delrin~ Platter 8 . Additional Parts • Hex Wrench (2) • Anti-skate Weight • Stylus Brush • · Platter Belt 5.
TRACKING FORCE AND ANTI-SKATE Install the supplied counterweight on the arm's endstub and balance the arm for zero tracking. For best results. use a stylus force gauge (sold separately through your local audio dealer), and set the tracking force as outlined by your cartridge manufacturer's specifications. If your model came with a prcinstalled MoF1 cartridge. simply install the counterweight until it lines up to the assigned location on the endstub.
VTA AND AZIMUTH 8 Front Llm~s If StudioDeck™came with StudioTracker™preinstalled, the following steps were completed at the factory After setting tracking force and anti-skate, adjust the tonearm·s height. Loosen the hex screw located at the base of the tonearm to raise or lower the arm height. and tighten once the arm is parallel to the record surface. Next, adjust your headshell and cartridge for correct azimuth.
CONNECTIONS AND LEVELING Install the RCA interconnects and ground wire to your preamp's phono section, and then connect the power cord from the turntable to any outlet or power conditioner of your choice. If the turntable is on an unleveled surface, place a bubble level on the platter, then carefully adjust each foot until the turntable's platter is true.
,ack to Front STYLUS CARE AND DUSTCOVER 0 Keep your records clean by using a high-quality record brush and record cleaner After each play, gently clean your stylus, always brushing back-tofront using the supplied stylus brush We also recommend using a liquid stylus cleaner such as Mobile Fidelity LP#9. When not in use, please cover your turntable with the supplied dustcover. For best sonic results, remove the dustcover while playing.
StudloDeck™ Ultra Deck™ Motor 300 RPM AC Synchronous 300 RPM AC Synchronous Speeds 33 1/3 RPM, 45.0 RPM 33 1/3 RPM, 45.0 RPM Platter 3.88 lb Delrin • 6 .8 lb Delrin .,, Wow & Flutter 0.017% - 0 .025% 0 .017% - 0 .025% Signal-To-Noise Ratio 72dB 74dB Power Supply Requirements 120V 60Hz, 220-230V S0Hz, l00V S0Hz 120V 60Hz, 220-230V S0Hz, 100V S0Hz Power Consumption < SW
ELECTRO~ICS www.mofielectronics.com , , , , ,c
vJJ/_fp MOFI ELECTRONICS LIMITED WARRANTY MoFi Electronics"' (referred to as "MoF1") warrants the product designated herein to be free of manufacturing defects in materials and workmanship for a period of three (3) years from the date of purchase by the original purchaser for any MoFi Electronics"' product. except phono cartridges, which are warranted for one (1) year from the date of purchase.
along with date of purchase, the name and address of the purchaser and authonzed MoFi Dealer, and the price paid by the purchaser. This warranty is for the sole benefit of the ong1nal purchaser of the covered product and shall not be transferred to a subsequent purchaser of the product. Any Implied warranties relating to the above product shall be llmlted to the duration of this warranty.
