3 mm Beschnitt umlaufend Megapixel 1280 x 960 software zoom -22°F to +140°F Weatherproof -30°C to +60°C, IP65 no heating necessary D22 X Camera Manual Part 1 IEEE 802.
D22M Camera Manual Part 1 MOBOTIX Camera Data Enter the data of your camera here! Camera Model: Camera Name: Factory IP Address: . . . Current IP Address: . . . activated DHCP: deactivated Admin User Name: Admin Password: D22 Basic D22 Secure D22 with Vandalism Set Note: MOBOTIX offers inexpensive seminars that include a workshop and practical excercises: Basic Seminar 3 days, Advanced Seminar 2 days. For more information, see www.mobotix.
1/100 D22M Camera Manual Part 1 D22M CAMERA MANUAL PART 1 1 INTRODUCTION 6 1.1 MOBOTIX Cost Benefits 10 1.2 MOBOTIX Technical Advantages 11 1.3 MOBOTIX D22M Concept 12 1.4 Feature Overview of the MOBOTIX D22M 15 1.5 Lenses for the MOBOTIX D22M 18 1.6 Important Notes 1.6.1 Password for the Administration Menu 1.6.2 Irreversibly Deactivating the Microphone 1.6.3 Starting the Camera Using the Factory IP Address 1.6.4 Resetting the Camera to Factory Defaults 1.6.
2/100 D22M Camera Manual Part 1 2.5 2.5.1 2.5.2 2.5.3 2.5.4 Mounting the Camera D22-IT/Secure D22-Basic Finishing the Installation Notes on Mounting the Camera to a Wall Without the Wall Mount 48 48 49 52 54 2.6 Mounting the D22 to a Ceiling Using the On-Wall Set 56 2.7 Mounting the D22 to a Ceiling Using the In-Ceiling Set 58 2.8 Mounting the D22 Vandalism Set 60 2.9 Mounting the D22 to a Wall Using the Wall Mount 62 2.10 Notes 2.10.1 Cleaning Instructions 2.10.
D22M Camera Manual Part 1 3/100 APPENDIX: HARDWARE AND SOFTWARE FEATURES IP65 CERTIFICATE DECLARATION OF CONFORMITY DRILLING TEMPLATES (SCALE 1:1) Note Download the latest ver- Chapters 4 and above are part of the Camera Software Manual (Software Manual in short). The main headings are listed below to give you an overview of the Software Manual contents. sion of this document as a SOFTWARE MANUAL PART 2 4 CAMERA USER INTERFACE 4.1 The First Image in the Browser 4.
4/100 D22M Camera Manual Part 1 6 SOFTWARE UPDATES 6.1 Overview 6.2 Preparatory Steps 6.3 Updating the Camera Software 6.4 Update Checklist 7 EVENTS, ACTIONS AND MESSAGES 7.1 Overview 7.2 Functional Overview 7.3 General Procedure 7.4 Screen Display of Event Settings in Live Image 7.5 Arming 7.6 Events 7.7 Actions and Messaging, Action and Messaging Profiles 7.8 Working with Profiles 7.9 Time Tasks 8 RECORDING 8.1 Overview 8.2 Recording Modes 8.
D22M Camera Manual Part 1 10 5/100 MOBOTIX CAMERAS ON THE WEB 10.1 Overview 10.2 Indirectly Accessing MOBOTIX Cameras via the Web 10.3 Directly Accessing MOBOTIX Cameras via the Web 10.4 Configuring the Router 10.5 DynDNS 11 SOFTWARE INTERFACES 11.1 Overview 11.2 Accessing the Camera's Live Image and the Event Images 11.3 Accessing the Camera's Live Image Using the Second Image Channel 11.4 Video Streaming 11.5 The HTTP API 12 TROUBLESHOOTING 12.1 Overview 12.2 Troubleshooting Checklist 12.
6/100 D22 Camera Manual Part 1 1 30 frames per second! Everything integrated! INTRODUCTION The D22 cameras are powerful yet compact network cameras by MOBOTIX, which are capable of creating high-resolution live video streams with high image rates. When showing VGA video (640x480), the camera can deliver up to 30 fps. Even Megapixel video (1280x960) will still generate up to 10 fps.
7/100 D22 Camera Manual Part 1 • D22-IT/Secure: The D22 IT and Secure models feature additional functions and security features. Among other things, you can connect an external speaker and microphone, store images and video sequences on an external file server (including audio) and call the camera using SIP video*. MOBOTIX also provides accessories for indoor and outdoor applications and vandalismprone areas. The camera is weatherproof (IP65) and thus suited for outdoor use.
8/100 D22 Camera Manual Part 1 In order to better adapt the camera to the surroundings, the Vadaism Set is available in the following versions: D22 Vandalism Set in different material and color versions - Stainless steel, matt - Stainless steel, polished - Stainless steel, white powder-coated - Stainless steel, black powder-coated - Stainless steel, silver powder-coated D22 In-Ceiling Set • D22 In-Ceiling Set: The D22 In-Ceiling Set allows mounting the D22 camera in fake ceilings, for example.
D22 Camera Manual Part 1 9/100 • D22 Wall Mount: The D22 Wall Mount is the ideal solution for mounting the D22 to walls for indoor and outdoor applications. The camera is absolutely dustproof and resistant against water jets (IP65). The wall mount also covers RJ45 wall outlets and also has ample space for additional modules.
10/100 D22 Camera Manual Part 1 1.
D22 Camera Manual Part 1 1.
12/100 D22 Camera Manual Part 1 1.3 MOBOTIX D22 Concept High-resolution live video with up to 30 frames/s at 640x480 * Accessories required: external microphone and external speaker The second generation of cameras from MOBOTIX delivers smooth live video display in VGA format with synchronous live audio, yet it keeps the network load to a minimum (approx. 2 Mbps)*. Live video display now matches the performance of analog video systems.
D22 Camera Manual Part 1 13/100 Long-term storage included MOBOTIX cameras (IT and Secure models) feature an integrated long-term storage system for Windows, Linux and Mac OS X computers. Every camera manages its own ring buffer storage space on the shared folder. Thanks to this decentralized technology, 30 live cameras can store images on a regular Pentium 4-class computer with 30 fps each, including audio (depending on the operating system).
14/100 D22 Camera Manual Part 1 Day & Night The Night version of the D22-Secure model delivers crisp and clear images of moving objects even at night since they use a special black and white image sensor. Depending on the lighting conditions, you can use infrared light to enhance the lighting, since the B/W sensor system is IR-sensitive (in contrast to the human eye).
D22 Camera Manual Part 1 15/100 1.4 Feature Overview of the MOBOTIX D22 The MOBOTIX D22 includes the following main features (some features are modeldependent): • Live images of up to 1280 x 960 pixels resolution via network and WiFi with up to 30 fps (at 640 x 480 VGA resolution), also adapted for PDAs. • Digital zoom with three stages (1x, 2x, 4x) and integrated panning (from 2x: clicking in the browser image will move the zoomed image section in the corresponding direction).
16/100 Speaker phone Telephony features using VoIP connections (Internet telephony)! * Accessories required: external microphone and external speaker * Accessories required: external microphone and external speaker D22 Camera Manual Part 1 • Time Tables for handling customized days, e.g. for holidays and vacations. The time tables are used to control the camera's arming, image recording, action, messaging, logo, obscure image and other features.
17/100 M22M D22M Secure Models D12 IT Models M12 Basic Models D22 Camera Manual Part 1 Software Features (All Models) Digital zoom (2x, 4x) with panning Motion JPEG/MxPEG video streaming X X/X X/X X/X Custom exposure windows X X X Video Motion detection X X X Time and event control (FTP, email, logos) X X X X X Time tables with holidays Web functionality (FTP, email) X X X Quad/MultiView in browser X X X Recording/Playback in browser X X X X X 10 50 Terabyte ring b
18/100 D22 Camera Manual Part 1 1.5 Lenses for the MOBOTIX D22 MOBOTIX currently offers five different lenses: from Super Wide-Angle L22 with 22 mm focal length up to the tele lens L135 with 135 mm focal length (equiv. to 35 mm camera). Since MOBOTIX cameras are backlight-proof, they do not require a mechanical auto iris. Without the iris as a mechanical component, all MOBOTIX glass lenses are extremely robust and maintenance-free.
19/100 D22 Camera Manual Part 1 Lens Table Order name L22 L32 L43 L65 L135 35mm equivalent 22 mm 32 mm 43 mm 65 mm 135 mm Focal length 4 mm 6 mm 8 mm 12 mm 25 mm Aperture 2,0 2,0 2,0 2,0 2.5 Image angle horizontally 90° 60° 45° 31° 15° Image angle vertically 67° 45° 34° 23° 11° Distance 1 m m m m m m • Image width 2,0 1.1 0.8 0.5 0.3 • Image height 1.3 0.8 0.6 0.4 0.2 Distance 5 m m m m m m • Image width 10.0 5.7 4.1 2.7 1.
20/100 D22 Camera Manual Part 1 1.6 Important Notes 1.6.1 Password for the Administration Menu Administration menu: User: admin Password: meinsm The administration area of the camera (Admin Menu button) is protected by a user name and password: • User name is admin • Password is meinsm Enter the user name and password exactly as shown above. Note that both entries are case-sensitive.
D22 Camera Manual Part 1 21/100 1.6.3 Starting the Camera Using the Factory IP Address If the camera's IP address is not known, you can start the camera with its factory IP address. Section 3.6, Starting the Camera Using the Factory IP Address, describes this procedure in more detail. 1.6.4 Resetting the Camera to Factory Defaults All settings of the MOBOTIX camera can be reset permanently to the factory default settings.
22/100 D22 Camera Manual Part 1 1.6.7 Deactivating the Automatic Daily Reboot of the Camera Deactivating the camera reboot In its default configuration, the MOBOTIX camera automatically reboots every morning at 3:36 am. The reason for this is that external influences (e.g. radiation in high locations) can lead to camera malfunctions. The automatic reboot will refresh the camera's memory and will ensure proper operation without requiring any interaction on the part of the user.
D22 Camera Manual Part 1 23/100 1.6.11 Additional Information For more information on this topic, see the News and Functional Overview pages in the online help of the camera's browser interface. Click on the yellow icon in the top right corner to open the camera's online help. In order to obtain more information on the camera and its current configuration, open the Camera Status dialog by clicking on the yellow icon in the top right corner of the camera's browser interface.
24/100 D22 Camera Manual Part 1 2 MOUNTING THE CAMERA 2.1 Preparing the Installation Before mounting the MOBOTIX D22, the following questions should be solved: 1) Where will the camera be mounted? Mounting the camera to a ceiling or wall, section 2.1.1 2) Which other mounting options are available? On-wall mounting, vandalism protection, wall mounting with Wall Mount, Corner and Pole Mount, in-ceiling mounting, section 2.1.
D22 Camera Manual Part 1 25/100 2.1.2 Additional Mounting Options for IT/Secure Models On-Wall Mounting The D22 On-Wall set can reliably protect external cables if the cables cannot be guided from below the housing but have to be led above the wall. In addition, the On-Wall mount provides ample space for extra modules. D22 On-Wall Set (IP65, also for Outdoor applications) In-Ceiling Mounting The D22 In-Ceiling Set allows mounting the D22 camera in fake ceilings, for example.
26/100 D22 Camera Manual Part 1 2.1.3 Network Connection and Power Supply, UPS Power over Ethernet (MxPoE) Power is supplied to all D22 models via the network cabling (MxPoE, Power-overEthernet). For smaller installations, the universal power supply (MX-SNT-E/U/GB/J/ AUS01-30-RJ) with the MOBOTIX Network Power Adapter MX-NPA-3-RJ is sufficient.
D22 Camera Manual Part 1 27/100 Using Uninterruptible Power Supplies (UPS) In order to maintain a continuous power supply even when utility power fails, you should install an uninterruptible power supply (UPS). These devices also provide full protection against electrical surges and voltage fluctuations and thus enhance the reliability of the system as a whole. When using a more powerful 19" rack-mounted USP, you can also protect all other network components (e.g. switches, routers, PoE switches, etc.).
D22 Camera Manual Part 1 2.1.5 Directions for Mounting Once the type of installation, the camera connections and the method of power supply have been decided upon, you should follow the directions listed below. This will ensure that you will only have to read the relevant sections of this chapter, which will speed up mounting the D22. Directions for Mounting Preparatory Tasks Sections All camera versions 2.1 Camera Version Sections D22-IT/Secure 2.
D22 Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
30/100 D22 Camera Manual Part 1 2.2 D22-IT/Secure: Delivered Parts, Components and Dimensions 2.2.1 Delivered Parts and Components D22-IT/Secure Camera housing (item 1) with mounting ring (item 9) 4 wood screws 4.5x60 mm (item 12) 4 dowels 8 mm (item 10) 4 washers ø5.3 mm (item 11) Lens (item 2) Lock ring (item 3) Make sure to check the delivered parts! Outer shell (item 8) ∅ 160 mm/6.3 in Dome (item 4) 4 Allen screws M4x16 mm (item 14) 4 washers ø4.
D22 Camera Manual Part 1 3131/100 /96 2.2.2 Camera Housing and Connections D22-IT/Secure The MOBOTIX D22-IT/Secure consists of the camera housing (motherboard, lens, dome), the outer shell and the mounting ring. Connections • • • • NET (Ethernet network/power supply) External audio support (Microphone/Speaker) Mini MxB/MOBOTIX bus (for future extensions) Slot for SD card (usable with a future software version) Outer shell Dome Lens unit Connections NET (back) Ext.
D22 Camera Manual Part 1 2.2.3 Dimensions of the D22-IT/Secure Freely positionable camera module 85 mm/3.3 in 32/100 ø 160 mm/6.3 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
33/100 D22 Camera Manual Part 1 2.2.4 Drilling Template for the D22-IT/Secure Mounting Ring 100 mm/3.9 in 100 mm/3.9 in 5.5 mm/0.22 in n 6i /5. m m .4 141 Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled nor adjusted to the paper size when printing the PDF file. When printing the PDF file, you should print two pages onto one using 100% scaling to obtain an unscaled printout of the drilling templates.
34/100 D22 Camera Manual Part 1 2.3 D22-Basic: Delivered Parts, Components and Dimensions 2.3.1 Delivered Parts and Components D22-Basic Camera housing (item 1) 4 wood screws 4.5x60 mm (item 12) 4 dowels 8 mm (item 10) 4 washers ø5.3 mm (item 11) Lens (item 2) Lock ring (item 3) Make sure to check the delivered parts! Toothed wrench (item 7) Dome (item 4) 4 Allen screws M4x16 mm (item 14) 4 washers ø4.3 mm (item 15) ∅ 129 mm/5.
D22 Camera Manual Part 1 35/100 2.3.2 Camera Housing and Connectors D22-Basic The MOBOTIX D22-Basic consists of the camera housing with the motherboard, the lens and the dome. Connections • • NET (Ethernet network/power supply) For external loudspeaker (Basic models only provide DHCP announcement) The MOBOTIX bus (MxB) and the SD card slot can only be used in D22-IT and Secure models using a future update of the camera software Dome Lens unit Connections NET (back) Ext.
D22 Camera Manual Part 1 2.3.3 Dimensions of the D22-Basic Freely positionable camera module 85 mm/3.3 in 36/100 ø 129 mm/5.1 in © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
37/100 D22 Camera Manual Part 1 2.3.4 Drilling Template for the D22-Basic 100 mm/3.9 in 0.89 in 22.5 mm/ 67.5 mm/2.7 in 45 mm/1.8 in ø5.4 mm/0.21 in 78 mm/3.1 in Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled nor adjusted to the paper size when printing the PDF file. When printing the PDF file, you should print two pages onto one using 100% scaling to obtain an unscaled printout of the drilling templates.
38/100 D22 Camera Manual Part 1 2.4 Camera Accessories: Delivered Parts, Components and Dimensions 2.4.1 D22 On-Wall Set Mounting set (item 16) The D22 is not included in the delivery of the OnWall Set! ∅ 165 mm/6.5 in 4 Allen screws M4x35 mm (item 17) 4 washers ø4.3 mm (item 18) Item 16 17 18 Count 1 4 4 Part Name Mounting set for D22 Stainless steel Allen screws M4x35 mm Stainless steel washers Ø 4.3 mm © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
39/100 D22 Camera Manual Part 1 Drilling Template for the D22 On-Wall Set 60 mm/2.4 in ø5.8 mm/2.3 in 100 mm/3.9 in Find the drilling templates (scale 1:1) at the end of the manual as a fold-out Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled nor adjusted to the paper size when printing the PDF file.
40/100 D22 Camera Manual Part 1 2.4.2 D22 In-Ceiling Set In-Ceiling mount (item 19) 5 clamps (item 22) The D22 is not included in the delivery of the InCeiling Set! ∅ 150 mm/5.9 in diameter Wrench for In-Ceiling mount (item 23) 5 winged cams (item 21) Decoration ring (item 20) Item 19 20 21 22 23 Count 1 1 5 5 2 Part Name In-Ceiling Set for D22 Decoration ring Winged cam Clamps Wrench for In-Ceiling mount © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
41/100 D22 Camera Manual Part 1 Drilling Template for the D22 In-Ceiling Set ∅ ter me a i d in 5.9 / mm 150 Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled nor adjusted to the paper size when printing the PDF file. When printing the PDF file, you should print two pages onto one using 100% scaling to obtain an unscaled printout of the drilling templates. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.
42/100 D22 Camera Manual Part 1 2.4.3 D22 Vandalism Set 4 security screws (item 26) 1 Vandalism ring (item 24) The D22 is not included in the delivery of the InCeiling Set! ∅ 160mm/6.
43/100 D22 Camera Manual Part 1 Available Colors of the D22 Vandalism Ring The D22 Vandalism Set provides added protection for D22 cameras. The set consists of a robust camera ring made of stainless steel and a reinforced dome made of 3 mm thick polycarbonate. A camera equipped with the Vandalism Set is perfectly suited for applications in demanding environments (such as prions, social hot-spots, train stations, etc.).
D22 Camera Manual Part 1 2.4.4 D22 Wall Mount Bottom plate (item 36) 4 wood screws 6x50 mm (item 32) 8 Allen screws M4x16 mm (item 34) Wall mount (item 29) 4 washers ø6.4 mm (item 31) 4 dowels 8 mm (item 30) 8 washers Ø 4.3 mm (item 35) Wall sealing (item 33) Item 29 30 31 32 33 34 35 36 Count 1 4 4 4 1 8 8 1 Part Name Wall Mount Dowels 8 mm Stainless steel washers Ø 6.
45/100 D22 Camera Manual Part 1 15 mm/ 0.59 in 75 mm/2.95 in Drilling Template for the D22 Wall Mount 160 mm/6.3 in Note Find the folded drilling template at the end of the manual. Make sure that the drilling template is not scaled nor adjusted to the paper size when printing the PDF file. When printing the PDF file, you should print two pages onto one using 100% scaling to obtain an unscaled printout of the drilling templates. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.
46/100 D22 Camera Manual Part 1 2.4.5 D22 Corner and Pole Mount 4 Allen screws M8x30 mm (item 37) The Corner and Pole mount can only be used in conjunction with the D22 Wall Mount 2 steel straps (item 40) 4 washers Ø 9 mm (item 38) 4 lock nuts M8 mm (item 39) * The appearance and the dimensions of the D22 Corner and Pole Mount may change Count 4 4 4 2 Part Name Stainless steel Allen screws M8x30 mm Stainless steel washers Ø 9 mm Stainless steel lock nuts M8 Stainless steel straps Height: 125 mm/4.
D22 Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
48/100 D22 Camera Manual Part 1 2.5 Mounting the Camera 2.5.1 D22-IT/Secure Before mounting the MOBOTIX D22-IT/Secure, you need to prepare the network connection and drill the holes for the fixtures: Find the folded drilling template for the mounting ring of the D22-IT/Secure models at the end of the manual! • Network connection: The network cabling is supplied through the ceiling directly above the camera. The cabling is perfectly protected and cannot be seen or damaged.
D22 Camera Manual Part 1 49/100 2.5.2 D22-Basic Before mounting the MOBOTIX D22-Basic, you need to prepare the network connection and drill the holes for the fixtures: • Network connection: The network cabling is supplied through the ceiling directly above the camera. The cabling is perfectly protected and cannot be seen or damaged. When preparing the installation, you should make sure that the cable runs at least 15 cm (6 in) within the camera housing (excluding the connector itself).
50/100 D22 Camera Manual Part 1 • Release the internal part of the camera by turning the ring inside in counter-clockwise direction using the supplied toothed wrench. While doing so, hold the camera at the lens unit to prevent it from turning. • Disengage the internal part of the camera with the lens unit from the base of the housing. • Position the base of the camera housing over the drilled holes and the prepared cable exit in the ceiling.
D22 Camera Manual Part 1 • Insert the internal part of the camera with the lens unit into the mounted base of the housing and secure it by turning the two blue clamps in clockwise direction using the supplied toothed wrench or a screwdriver. This will prevent the internal part of the camera to accidentally fall out of the base before it has been secured.
52/100 D22 Camera Manual Part 1 2.5.3 Finishing the Mounting Process Establishing a Connection to the Camera • Establish a connection to the camera as described in section 3.4, Establishing a Connection to the Camera. Adjusting the Lens, Visual Check Make sure that you see the live image of the camera on the monitor of your computer or laptop. Now adjust the lens until you see the desired image area on your monitor. • Remove the camera dome.
D22 Camera Manual Part 1 • • Once you are seeing the desired image area, tighten the Allen screws at the sides of the lens unit (in clockwise direction) and the toothed ring inside the camera. Do not use excessive force when doing so to avoid damaging the camera. Release the lens' lock ring and adjust the image focus by turning the lens in its holder. Check the image on the computer monitor. Make sure that you tighten the lock ring again once you are finished.
54/100 D22 Camera Manual Part 1 2.5.4 Notes on Mounting the Camera to a Wall Without the Wall Mount The MOBOTIX D22 has been designed to be mounted to either ceilings or to a wall, when using the Wall Mount. It is also possible to mount the D22 directly to a wall (without using the Wall Mount), but doing so will result in reduced flexibility for positioning the lens. The following section contains some hints on these restrictions and tips for mounting the camera to a wall.
55/100 D22 Camera Manual Part 1 Tilt the camera to see a larger area of the room (camera mounted 1 m/3 ft to the left of the center) 1m/3ft 1m/3ft 0° 1m/3ft 10° 30° This effect also appears when mounting a D22 at the center of a wall and you are turning the base of the camera. This will also allow to capture a larger area of the room with the camera, but the image is again tilted.
56/100 D22 Camera Manual Part 1 2.6 Mounting the D22 to a Ceiling Using the On-Wall Set Before mounting the MOBOTIX D22-IT/Secure to an indoor or outdoor location using the On-Wall Set, you need to prepare the network connection and drill the holes for the fixtures: • Network connection: You can use any one of the four openings in the OnWall mount to guide the cabling into the camera.
D22 Camera Manual Part 1 • Disengage the mounting ring from the housing of the D22-IT/Secure. This ring is not required when mounting the camera to the OnWall Set. • Connect the network cable to the network cable of the camera using a patch cable connector. Make sure to leave enough unused cable within the housing. This will ensure that you can turn the lens unit freely later on. Cable that is too long can be stored easily within the On-Wall mount.
58/100 D22 Camera Manual Part 1 2.7 Mounting the D22 to a Ceiling Using the In-Ceiling Set Before mounting the MOBOTIX D22-IT/Secure to an indoor location using the InCeiling Set, you need to prepare the network connection and drill the hole for the camera: • Find the drilling template at the end of the manual Network connection: The network cabling is supplied through the ceiling directly above the camera.
D22 Camera Manual Part 1 • 59/100 Insert the In-Ceiling Set with the camera into the hole in the ceiling. Tightening the integrated mounting screws will automatically secure the In-Ceiling mount to the ceiling. The winged cams automatically secure the InCeiling Set in the ceiling when tightening the screws (see detail pictures) Winged cam • Finally, press the decoration ring onto the mount and lock in place by turning it in clockwise direction.
60/100 D22 Camera Manual Part 1 2.8 Mounting the D22 Vandalism Set In order to install the Vandalism Set, replace the regular outer shell and the Allen screws with the stainless steel shell, the security screws and the four spacers of the Vandalism Set. Likewise, replace the dome of the D22-IT/Secure with the reinforced dome of the Vandalism Set. • Remove the outer shell. Remove all four Allen screws using the supplied Allen wrench. Take off the outer shell. • Remove the camera dome.
D22 Camera Manual Part 1 • Mount the stainless steel shell of the Vandalism Set. Do not forget to insert the four spacers of the Vandalism Set into their seats in the camera housing! • Mount the supplied stainless steel shell with the security screws and use the supplied two-hole driver bit to firmly tighten the screws. © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
62/100 D22 Camera Manual Part 1 2.9 Mounting the D22 to a Wall Using the Wall Mount Before mounting the MOBOTIX D22-IT/Secure with the Wall Mount you need to prepare the network connection and drill the holes for the fixtures: • Network connection: The network cabling is supplied through the opening in the back of the wall mount. The cabling is perfectly protected by the mount and cannot be seen or damaged.
D22 Camera Manual Part 1 • Connect the network cable to the network cable of the camera using a patch cable connector (or plug the cable directly into the RJ45 wall outlet). Make sure to leave enough unused cable within the housing. This will ensure that you can turn the lens unit freely later on. Cable that is too long can be stored easily within the housing. • Now press the D22 into the guides of the wall mount.
64/100 D22 Camera Manual Part 1 2.10 Notes 2.10.1 Cleaning Instructions Cleaning the Dome • • • • In order to protect the dome from being scratched and from getting dirty, only handle the dome using a soft cotton cloth or the protective plastic of the camera's shipping box. You should clean the dome at regular intervals. Always use a lint-free cotton cloth for this purpose. If the dirt is more persistent, add a mild alcohol-free detergent without abrasive particles.
D22 Camera Manual Part 1 • Avoid induction: When running data cables parallel to existing regular power lines or high-voltage wires, make sure you observe the minimum distances to the power cables. Fire Prevention When installing the power lines to the camera, make sure you always adhere to the relevant regulations on wiring and fire prevention at the site of the installation.
66/100 D22 Camera Manual Part 1 2.11 Camera Accessories Power supply (MX-SNT-E/U/GB/J/AUS01-30-RJ) The MOBOTIX power supply is required if you do not use a Network Power Rack or Network Power Box, or a PoE-compatible switch or router. Network Power Adapter (MX-NPA-3-RJ) The Network Power Adapter allows injecting the power supply for the MOBOTIX camera into the network cable. It thus allows using the network cable for connecting to the camera and for remotely supplying power (up to 100 m (300 ft)).
D22 Camera Manual Part 1 67/100 On-Wall Set The D22 On-Wall set can reø 165 mm x 37mm liably protect external /6.5 x 1.5 in cables if the cables cannot be guided from below the housing but have to be led above the wall for technical or legal reasons. In addition, the On-Wall mount provides ample space for extra modules. The D22 is not included in the delivery of the InCeiling Set! (IP65) In-Ceiling Set The D22 In-Ceiling Set allows mounting the D22 camera in fake ceilings, for example.
68/100 D22 Camera Manual Part 1 Corner and Pole Mount If you would like to mount the MOBOTIX D22 to a pole, you should consider using the MOBOTIX Corner and Pole Mount. The Corner and Pole mount can only be used in conjunction with the Wall Mount. The supplied stainless steel straps allow fixing the mount to poles with diameters between 60 and 180 mm (2.4 to 7.1 in). Like the Outdoor Wall Mount, the Corner and Pole Mount is made from weatherproof material and is just as robust and maintenance-free.
D22 Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
70/100 D22M Camera Manual Part 1 3 OPERATING THE CAMERA 3.1 General Procedure The MOBOTIX camera does not require any software installation; all you need is your preferred browser with JavaScript support to operate the camera. Thus, the MOBOTIX camera is supported by all common operating systems (such as Windows, Macintosh and Linux, ...). 3.1.
D22M Camera Manual Part 1 71/100 Note After first booting a new MOBOTIX camera or after resetting to factory defaults, accessing the Administration menu (Admin Menu button) will automatically start the Quick Installation wizard. This is where you configure the most important camera parameters in a step-by-step manner. If you have completed the Quick Installation wizard at least once, the standard Administration menu will open when you click on the Admin Menu button.
72/100 D22M Camera Manual Part 1 3.2 Overview of the Configuration Settings Once the connection has been established, you can configure the camera by clicking on the Admin Menu button or the Setup Menu button. Using the Quick Installation wizard After first booting the camera or after resetting it to factory defaults, any access to the administration menu (Admin Menu button) will start the Quick Installation.
D22M Camera Manual Part 1 Once you have finished configuring the camera, you should always store the settings in the camera's permanent memory. You can do so in each dialog (clicking on Set at the bottom of each dialog will temporarily set the changes; clicking on Close will ask you to store the complete configuration in the cameras permanent memory) or in the Configuration section of the administration menu (Admin Menu > Store current configuration into flash memory).
74/100 D22M Camera Manual Part 1 3.3 Connecting the Camera to the Network and to the Power Supply 3.3.1 Notes on Cable Lengths and Power Supply MOBOTIX PoE products have zero maintenance and are reliable as the systems do not require fans PoE components without fans increase overall reliability of the entire system • The power supply of the camera can only be established using the 10BaseT/NET connector of the camera with the (pre-installed) network cable.
75/100 D22M Camera Manual Part 1 3.3.2 Camera Startup Sequence As soon as the power supply is established, the camera's LEDs will provide information on the startup sequence of the camera. • • • Booting: Immediately after connecting the power supply, the red LED lights up, blinks for two seconds, then stays on permanently. The camera's boot loader checks the hardware, unpacks and starts the operating system.
76/100 MOBOTIX power supply and Network Power Adapter required D22M Camera Manual Part 1 3.3.3 Power Supply (MxPoE) Using a Switch • • • Connect the factory pre-installed cable of the camera to the Camera connector of the Network Power Adapter. Connect the LAN/Power connector of the Network Power Adapter to an Ethernet connector of the switch/router or the Ethernet wall outlet. Plug the RJ45 connector of the external power unit into the PC/Power connector of the Network Power Adapter. 3.3.
D22M Camera Manual Part 1 3.3.5 Power Supply (MxPoE) Using a Network Power Rack or Network Power Box • • Connect the factory pre-installed cable of the camera to the CAM connector of the Network Power Rack (MX-NPR-8/20) or the Network Power Box (MX-NPR-4). Connect the LAN connector of the Network Power Rack or Network Power Box to an Ethernet connector of the switch/router.
78/100 D22M Camera Manual Part 1 3.4 The First Image from the Camera Once the Ethernet connection has been established, you have the following possibilities to see the first image of the camera: Working with the webbased user interface only requires a web browser with activated JavaScript! • • Automatic camera search and configuration using MxControlCenter (free Windows client for MOBOTIX cameras; section 3.4.6, The First Image in MxControlCenter) Manual configuration (section 3.4.
D22M Camera Manual Part 1 Make sure that no other network device uses the camera's IP address: • Open a command shell (Windows) or a terminal (Linux/UNIX/OS X) and enter the following command: ping If you receive an answer from another network device although the camera is not connected, you will have to remove that device until you have reset the MOBOTIX camera to a free IP address. We recommend using the Quick Installation wizard for assigning a new IP address to the camera.
80/100 D22M Camera Manual Part 1 3.4.2 The First Image in the Browser Camera access: http://10.1.0.99 (example IP) The factory IP address is printed on the sticker on the camera housing Administration menu: User Name: admin Password: meinsm Now that you have successfully started the camera for the first time, you can access the camera using your preferred browser to see the live video stream and the user interface.
D22M Camera Manual Part 1 If you have started the camera using DHCP or you have set the IP address manually, enter the new IP address in the browser address bar (e.g. 192.168.0.99) instead of the factory IP address. 81/100 Changing the factory IP address: Always use Admin Menu > Quick Installation Note The MOBOTIX camera can announce its current IP address over the speaker. For additional information on this topic, see section 3.6, Starting the Camera With an Automatic IP Address (DHCP).
82/100 D22M Camera Manual Part 1 3.4.4 Camera Screens in the Browser Per factory default, the MOBOTIX camera first shows the Live screen. You can set a different start page in order to prevent others from changing the settings. In addition to this, you can assign user names and passwords to prevent unauthorized access or you can restrict access to the current live image only by setting the Guest screen as the start page.
D22M Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
84/100 D22M Camera Manual Part 1 3.4.5 Access Using Zeroconf/Bonjour Bonjour is the implementation of this service in Apple Mac OS X from version 10.4; in Mac OS X 10.2 and 10.3, this service is called Rendezvous. Bonjour is available free of charge for Windows computers from the Apple web site www.apple.com/bonjour. For Linux and Unix, Avahi provides the corresponding functionality. For further information on Bonjour and Zeroconf, please consult www.apple.
D22M Camera Manual Part 1 85/100 Prerequisites for using Zeroconf/Bonjour MOBOTIX camera: • • Zeroconf has to be activated (Admin Menu > Ethernet Interface). This is the factory default for MOBOTIX cameras from software version 3.0.3.37. The camera needs to be in the same physical subnet as the computer (Admin Menu > Ethernet Interface). Operating system: • Microsoft Windows (2000, XP, 2003, Vista): Bonjour for Windows has to be installed (www.apple.com/bonjour).
86/100 D22M Camera Manual Part 1 • Macintosh OS X (10.2 or higher): Bonjour is included in the Apple operating system. There is no other configuration required. The list of Bonjour-enabled network devices is displayed in Safari after clicking on the Bonjour button. • Linux: Zeroconf is included in KDE from version 3.4 and in Gnome from version 2.8. The list of Bonjour-enabled network devices is displayed after entering zeroconf:/ in the Konqueror address bar.
D22M Camera Manual Part 1 87/100 Note If a proxy server is used in your network, you may get an error message when trying to access a MOBOTIX camera in the web browser. Make sure that the list of proxy exceptions in your browser contains the following entry: *.local *.local. .local. (Windows) (Mac OS X) (Linux) To find the proxy exceptions in Internet Explorer for Windows, open Tools > Connections > LAN Settings > Settings > Proxy server > Advanced and add the entry in the Exceptions text field.
88/100 D22M Camera Manual Part 1 3.4.6 The First Image in MxControlCenter Download MxControlCenter free of charge from www.mobotix.com MOBOTIX MxControlCenter is a free Windows application that allows displaying multiple MOBOTIX cameras on one computer and provides alarm management functions. It can easily handle displaying 30 cameras with CIF resolution simultaneously at 30 fps each in MxPEG format on one standard PC with Intel Pentium 4 and 3 GHz.
D22M Camera Manual Part 1 89/100 Installing MxControlCenter If you have an MxControlCenter installation CD, insert it into your computer drive. If this is not the case or if you would like to update an older version, you can download the latest Windows installer (MSI file) from the MOBOTIX website and then manually install the current version. The latest version is available at www.mobotix.com > Support > Software-Downloads in the MxControlCenter section.
90/100 D22M Camera Manual Part 1 Using MxControlCenter for the First Time Double-click the shortcut created by the installer (see Installing MxControlCenter) or the program file itself to start MxControlCenter. Automated Search for MOBOTIX Cameras If you start MxControlCenter for the first time or if you have not yet stored a start layout with the desired video sources (i.e. MOBOTIX cameras), the Open Video Sources dialog will open and automatically starts scanning the network.
D22M Camera Manual Part 1 91/100 Click on OK to add the selected cameras to the Open Video Sources dialog. Anytime you connect a new camera to the local network, you can initiate the search in the Open Video Sources dialog again by pushing the button. If the desired MOBOTIX cameras are highlighted in the video source list, proceed to Selecting Video Sources.
92/100 D22M Camera Manual Part 1 MxControlCenter changes the network configuration of the current camera and, after a short time, the camera also appears in the list with a new IP address and in the same subnet as your computer. Make sure that the Save camera configuration permanently checkbox is activated so that the new network settings will be used from now on and not just until the camera's next reboot.
D22M Camera Manual Part 1 Editing the video source list This list provides a popup menu (right mouse key), allowing you to select/deselect all video sources at once. Similarly, you can highlight some or all of the listed video sources and remove them from the list if they are not to be displayed or managed in MxControlCenter.
94/100 D22M Camera Manual Part 1 3.5 Starting the Camera With an Automatic IP Address (DHCP) If your network has a DHCP server, you can start the camera with DHCP support. In this case, the DHCP server automatically assigns an IP address. Connect and activate the external speaker of the camera! As soon as startup has been completed, the camera automatically announces its IP address, its network mask and its MAC address (note that this feature requires an external speaker).
95/100 D22M Camera Manual Part 1 3.6 Starting the Camera Using the Factory IP Address In certain situations, it may become necessary to start the camera with its factory IP address. This could be the case, for example, if the IP address has been lost or the camera does not react to the last known IP address.
D22M-IT Mx-D22M-IT-D22 D22M-Sec Mx-D22M-Sec-D22 D22M-Sec-Night Mx-D22M-Sec-Night-N22 D22M Camera Manual Part 1 D22M-Basic Mx-D22M-Basic-D22 96/100 IP54 IP65 IP65 IP65 M M M M Image sensor Color Color Color B/W Resolution VGA VGA Mega Mega 640x480 640x480 1280x960 1280x960 16/16/- 30/30/- 30/30/10 30/30/10 1 1 1 0.1 Sensitivity at 1 second (Lux) 0.05 0.05 0.05 0.
97/100 D22M Secure Models M22M IT Models D12 Web Models M12 Basic Models D22M Camera Manual Part 1 Software Features (All Models) Digital zoom (2x, 4x) with panning Motion JPEG/MxPEG video streaming X X X/X X/X X/X X/X Custom exposure windows X X X X Video Motion detection X X X X Time and event control (FTP, email, logos) X X X X X X X Time tables with holidays Web functionality (FTP, email) X X X X Quad/MultiView in browser X X X X Recording/Playback in browser
98/100 D22M Camera Manual Part 1 Declaration of Conformity © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
D22M Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
100/100 D22M Camera Manual Part 1 Notes: © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
D22M Camera Manual Part 1 MOBOTIX ... the new face of IP video All images in this manual are genuine MOBOTIX camera images. Enjoy the image quality! Manufacturer: CEO: MOBOTIX AG Luxemburger Str. 6 67657 Kaiserslautern Germany Dr. Ralf Hinkel Phone: +49 (631) 3033-103 Fax: +49 (631) 3033-190 Tax Code: 19/650/0812/1 Tax Office: Kaiserslautern http://www.mobotix.com sales@mobotix.
D22-BASIC: Drilling Template Scale 1:1 © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
D22-IT/SECURE: Drilling Template Scale 1:1 © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
D22-On Wall Set: Drilling Template Scale 1:1 © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
D22-In Ceiling Set: Drilling Template Scale 1:1 ter e iam D © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
D22-FixDome Outdoor Wall Mount: Drilling Template Scale 1:1 © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
Notes © MOBOTIX AG • Security-Vision-Systems • Made in Germany www.mobotix.com • sales@mobotix.
3 mm Beschnitt umlaufend Megapixel 1280 x 960 software zoom -22°F to +140°F Weatherproof -30°C to +60°C, IP65 no heating necessary D22 X Camera Manual Part 1 IEEE 802.
