Co. Ltd. Modem User Manual

ManualsBrandsMocomtech ManualsModemCIM-550

CiM-550

IP-Enabled Satellite Modem

Installation and Operation Manual

Part Number CD/CIM550.IOM

Rev. 2

December 3, 2002

Summary of content (460 pages)

PAGE 1
CiM-550 IP-Enabled Satellite Modem Installation and Operation Manual Part Number CD/CIM550.IOM Rev.
PAGE 2
PAGE 3
Errata A Comtech EFData Documentation Update Subject: Changes to Chapter 5 Serial Remote Control Date: Document: December 16, 2002 CiM-550 Satellite Modem Installation and Operation Manual, Rev. 2, dated December 16, 2002 CD/CiM550.EA2 Attach this page to page 5-9 Part Number: Collating Instructions: Comments: The following changes provide updated information TX Carrier On/Off State. This information will be incorporated into the next revision.
PAGE 4
Errata B Comtech EF Data Documentation Update Subject: Addition to Chapter 4, Front Panel Menus Date: Document: January 15, 2003 CiM-550 IP Enabled Satellite Modem Installation and Operation Manual, Rev. 2, dated December 16, 2002 CD/CiM550.EB2 Attach this page to page 47 Part Number: Collating Instructions: Comments: The following changes provide additional information for Front Panel Menus. This information will be incorporated into the next revision. Change Specifics: 4.1.6.
PAGE 5
CiM-550 Comtech EF Data is an ISO 9001 Registered Company. IP Satellite Enable Modem Installation and Operation Manual Part Number CD/CIM550.IOM REV. 2 December 3, 2002 Copyright © Comtech EF Data, 2002. All rights reserved. Printed in the USA.
PAGE 6
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOM CUSTOMER SUPPORT Contact the Comtech EF Data Customer Support Department for: Product support or training Information on upgrading or returning a product Reporting comments or suggestions concerning manuals Contact Customer Support using any of the following methods: Mail: Comtech EF Data Customer Support Department 2114 West 7th Street Tempe, Arizona 85281 USA Email: cimfss@comtechefdata.com Internet: www.comtechefdata.
PAGE 7
Table of Contents FIGURES ..................................................................................................................... XV TABLES...................................................................................................................... XVI CHAPTER 1. INTRODUCTION.................................................................................... 1 1.1 Introduction............................................................................................................
PAGE 8
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM 2.3 Configuration ........................................................................................................................ 14 2.4 Select Internal IF Loop......................................................................................................... 14 2.5 Connect External Cables...................................................................................................... 14 2.
PAGE 9
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM 5.5.4 Instruction Code Qualifier ............................................................................................... 58 5.5.5 Message Arguments......................................................................................................... 60 5.5.6 End Of Packet .................................................................................................................. 60 CHAPTER 6.
PAGE 10
CiM-550 IP Enabled Satellite Modem Preface CHAPTER 10. Rev. 2 CD/CIM550.IOMCD/CIM550.IOM CONNECTOR PINOUTS ................................................................. 111 10.1 Data Connector - 25 Pin ‘D’ Type Female...................................................................... 111 10.2 Alarms Connector - 15 Pin ‘D’ Type Male..................................................................... 112 10.3 Remote Control Connector - 9 Pin ‘D’ Type Male ..........................................
PAGE 11
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM 13.1 SNMP Interface................................................................................................................. 211 13.2 MIB-II ................................................................................................................................ 211 13.2.1 System Group............................................................................................................... 212 13.2.
PAGE 12
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM 13.7.23 cimDatagramCompressionOption.............................................................................. 278 13.7.24 cimNaptOption........................................................................................................... 279 13.7.25 cimQosOption ............................................................................................................ 279 13.7.26 cimTcpAccelerationOption...............
PAGE 13
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM 13.7.68 cimSatelliteInterface .................................................................................................. 300 13.7.69 cimSatelliteIpAddress ................................................................................................ 300 13.7.70 cimSatelliteSubnetPrefixLen ..................................................................................... 301 13.7.71 cimSatelliteReceiveEnable .........
PAGE 14
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM 13.7.113 cimArpTable ............................................................................................................ 323 13.7.114 cimArpEntry ............................................................................................................ 324 13.7.115 cimArpIndex ............................................................................................................ 324 13.7.116 cimArpIpAddress.......
PAGE 15
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM 13.7.158 cim............................................................................................................................ 346 13.7.159 IpOptionPacketsReceived ........................................................................................ 347 13.7.160 cimDroppedPacketsTotal......................................................................................... 347 13.7.161 cimDroppedPacketsTTLExpired ....
PAGE 16
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM 13.9.26 cim550RxFECType ................................................................................................... 372 13.9.27 cim550RxFECCodeRate............................................................................................ 373 13.9.28 cim550RxSpecInv...................................................................................................... 373 13.9.29 cim550RxDescrambler .......................
PAGE 17
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM 13.9.71 cim550NotificationsPrefix......................................................................................... 394 13.9.72 cim550ModemUnitFaultsNotification....................................................................... 395 13.9.73 cim550ModemTxTrafficFaultsNotification .............................................................. 395 13.9.74 cim550ModemRxTrafficFaultsNotification ............................
PAGE 18
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM 13.9.116 oduRetrieveNext5Events ......................................................................................... 416 13.9.117 oduNotifications....................................................................................................... 417 13.9.118 oduNotificationsPrefix............................................................................................. 417 13.9.119 oduUnitFaultsNotification ..........
PAGE 19
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM Figures Figure 1-1. Typical Coarse AGC Voltage Characteristic ............................................................ 10 Figure 1-2. Cim-550 Dimensional Envelope ............................................................................... 11 Figure 3-1. Front Panel ................................................................................................................ 18 Figure 3-2. Rear Panel ....................
PAGE 20
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM Tables Table 4-1. Front Panel LED Indicators........................................................................................ 23 Table 7-1. Viterbi Decoding Summary........................................................................................ 92 Table 7-2. Sequential Decoding Summary .................................................................................. 93 Table 10-1.
PAGE 21
CiM-550 IP Enabled Satellite Modem Preface Table 13-24. Table 13-25. Table 13-26. Table 13-27. Table 13-28. Table 13-29. Table 13-30. Table 13-31. Table 13-32. Table 13-33. Table 13-34. Table 13-35. Table 13-36. Table 13-37. Table 13-38. Table 13-39. Table 13-40. Table 13-41. Table 13-42. Table 13-43. Table 13-44. Table 13-45. Table 13-46. Table 13-47. Table 13-48. Table 13-49. Rev. 2 CD/CIM550.IOMCD/CIM550.IOM Ethernet Interface Subgroup OIDs .............................................................
PAGE 22
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM ABOUT THIS MANUAL This manual provides installation and operation information for the Comtech EF Data Cim-550 IP Enabled Satellite Modem. This is a technical document intended for earth station engineers, technicians, and operators responsible for the operation and maintenance of the Cim-550 IP Enabled Satellite Modem.
PAGE 23
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM REPORTING COMMENTS OR SUGGESTIONS CONCERNING THIS MANUAL Comments and suggestions regarding the content and design of this manual will be appreciated. To submit comments, please contact the Comtech EF Data Customer Support Department. EMC COMPLIANCE This is a Class A product. In a domestic environment, it may cause radio interference that requires the user to take adequate protection measures.
PAGE 24
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM LOW VOLTAGE DIRECTIVE (LVD) The following information is applicable for the European Low Voltage Directive (EN60950): Type of power cord required for use in the European Community. ! CAUTION: Double-pole/Neutral Fusing. ACHTUNG: Zweipolige bzw. Neutralleiter-Sicherung. International Symbols: Symbol Definition Symbol Definition Alternating Current. Protective Earth. Fuse. Chassis Ground.
PAGE 25
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.IOM EXCLUSIVE REMEDIES The remedies provided herein are the buyer's sole and exclusive remedies. Comtech EF Data shall not be liable for any direct, indirect, special, incidental, or consequential damages, whether based on contract, tort, or any other legal theory. DISCLAIMER Comtech EF Data has reviewed this manual thoroughly in order that it will be an easy-touse guide to your equipment.
PAGE 26
CiM-550 IP Enabled Satellite Modem Preface Rev. 2 CD/CIM550.IOMCD/CIM550.
PAGE 27
Chapter 1. Introduction Introduction 1 Major Assemblies 2 Options 4 Specifications 6 Dimensional Envelope 11 CiM-550 IP-Enabled Satellite Modem 1.1 INTRODUCTION The CiM-550 is a high-performance, low-cost, IP-enabled satellite modem designed for closed network Single Channel Per Carrier (SCPC) links. It is ideal for many VSAT applications. Offering a range of data rates from 2.4 to 2048 kbps in 1 bit per second steps, the modem includes Viterbi forward error correction as standard.
PAGE 28
CiM-550 IP Enabled Satellite Modem Introduction Rev. 2 CD/CIM550.IOM 1.2 MAJOR ASSEMBLIES Assembly Description PL/0391 Modem Card PL/9161-1 IP Module 1.
PAGE 29
CiM-550 IP Enabled Satellite Modem Introduction Rev. 2 CD/CIM550.IOM 1.3.2 SOFTWARE The internal software is both powerful and flexible, permitting storage and retrieval of up to 10 different modem configurations. The modem uses ‘flash memory’ technology internally, and new firmware can be uploaded to the unit from an external PC. This simplifies software upgrading, and updates can now be sent via the Internet, E-mail, or on disk.
PAGE 30
CiM-550 IP Enabled Satellite Modem Introduction Rev. 2 CD/CIM550.IOM 1.4 OPTIONS Enhancing the CiM-550’s performance is easy. Additional features can be added quickly on site, using the FAST access code purchased from Comtech EF Data. To enable these features, simply enter the code at the front panel. Description Software Version Turbo Product Coding (TPC) 1.0.1 and Later TCP acceleration Future DES Data Encryption 1.0.
PAGE 31
CiM-550 IP Enabled Satellite Modem Introduction Rev. 2 CD/CIM550.IOM 1.4.4 IP DATAGRAM COMPRESSION Optionally, the CiM-550 supports IP datagram compression to provide improved bandwidth. IP payload is compressed while the IP Headers remain unaffected. 1.4.5 IP HEADER COMPRESSION Optionally, the CiM-550 supports IP header compression to provide improved bandwidth usage especially for smaller datagrams where the header overhead could be significant (e.g. VoIP). 1.4.
PAGE 32
CiM-550 IP Enabled Satellite Modem Introduction Rev. 2 CD/CIM550.IOM 1.5 SPECIFICATIONS SYSTEM SPECIFICATIONS (FULLY ENHANCED) Frequency Range 52 to 88 MHz, 104 to 176 MHz (option), stability ± 1.5 ppm, 0 to 500 C Input/Output Impedance 50 and 75 Ohms (Front panel selectable), 17 dB min. return loss IF Connector BNC, female Data Interface 10baseT/100baseTX Ethernet (RJ-45 connector) DB25 female, providing: (CDM-550 mode only) EIA422/EIA530 DCE V.35 DCE X.
PAGE 33
CiM-550 IP Enabled Satellite Modem Introduction Rev. 2 CD/CIM550.IOM FEC FEC None: Uncoded BPSK/QPSK/OQPSK Viterbi: k=7, per IESS 308/309 BPSK: Rate 1/2 QPSK/OQPSK: Rate 1/2, Rate 3/4 and Rate 7/8 Sequential: k=36 (Rate 1/2) per IESS 309 k= 63 (Rate 3/4) per IESS 309 k= 87 (Rate 7/8) Turbo Product Codec (Optional plug-in card): Rate 3/4 QPSK - 2 dimensional Rate 21/44 BPSK - 3 dimensional Rate 5/16 BPSK - 3 dimensional Overhead Framed EDMAC/AUPC 5% overhead (Except Turbo BPSK modes, which add 1.
PAGE 34
CiM-550 IP Enabled Satellite Modem Introduction Rev. 2 CD/CIM550.
PAGE 35
CiM-550 IP Enabled Satellite Modem Introduction Rev. 2 CD/CIM550.IOM Example: At 512 kbps, R1/2 QPSK, ± 30 kHz sweep, acquisition time = 0.25 seconds, average Clock tracking range ± 100 ppm min. BER PERFORMANCE (Met with two adjacent carriers 7 dB higher) Guaranteed Eb/No, in dB (Typical values in parentheses) Viterbi ½ ¾ 7/8 10-5 5.4 (4.9) 6.8 (6.3) 7.7 (7.2) -6 6.0 (5.5) 7.4 (6.9) 8.4 (7.9) 10-7 6.7 (6.2) 8.2 (7.7) 9.0 (8.6) Sequential (64 kbps) 10 ½ ¾ 7/8 10 -5 4.8 (4.2) 5.
PAGE 36
CiM-550 IP Enabled Satellite Modem Introduction Rev. 2 CD/CIM550.IOM Figure 1-1.
PAGE 37
CiM-550 IP Enabled Satellite Modem Introduction Rev. 2 CD/CIM550.IOM 1.6 DIMENSIONAL ENVELOPE Figure 1-2.
PAGE 38
CiM-550 IP Enabled Satellite Modem Introduction Rev. 2 CD/CIM550.
PAGE 39
Chapter 2. Installation Unpacking and Inspection 13 Mounting Kits 13 Configuration 14 Select Internal IF Loop 14 Connect External Cables 14 Connector Description 14 2.1 UNPACKING AND INSPECTION Inspect shipping containers for damage. If shipping containers are damaged, keep them until the contents of the shipment have been carefully inspected and checked for normal operation. Remove the packing list from the outside of the shipping carton.
PAGE 40
CiM-550 IP Enabled Satellite Modem Installation Rev. 2 CD/CIM550.IOM The CiM-550 is very light - under 7 lbs (3.2 kgs), and very short - 12 ins (305 mm). For this reason, it has not been designed to have rack slides mounted to the side of the chassis. However, Comtech EF Data recommends that some method of support within the rack should be employed, such as rack shelves. If there is any doubt, please consult the factory. 2.
PAGE 41
CiM-550 IP Enabled Satellite Modem Installation Rev. 2 CD/CIM550.IOM FOR CONTINUED OPERATOR SAFETY, ALWAYS REPLACE THE FUSES WITH THE CORRECT TYPE AND RATING. IF Ports - The IF port connectors are both a 50 ohm BNC female type. 75 ohm cable connectors (male) will have no problem mating with this 50 ohm type. Data - The primary Data connector for the CiM-550 is the RJ-45 connector providing the 10/100 BaseT Ethernet interface.
PAGE 42
CiM-550 IP Enabled Satellite Modem Installation Rev. 2 CD/CIM550.IOM Auxiliary Serial Port - The Auxiliary Serial connector is an HE1402 3 pin header. A suitable mate for this connector is AMP part number 281838-3, with three crimp pins, AMP part number 182734-2, also required. This is an additional EIA-232 serial port, which is only used when the modem is part of a 1:1 pair. The pinout details for this connector are provided in the next section.
PAGE 43
Chapter 3. Operation Methods of Operation 17 Front Panel Operation 18 Telnet Operations 18 Web Server Operation 18 Telnet Operations 18 SNMP Operations 19 Serial Remote Control Operations 18 Serial Command Line Interface (CLI) Operations 18 3.
PAGE 44
CiM-550 IP Enabled Satellite Modem Operation Rev. 2 CD/CIM550.IOM LED Panel Keypad UNIT STATUS STORED EVENT TRANSMIT TRAFFIC REMOTE RECEIVE TRAFFIC EDMAC MODE ON LINE TEST MODE Display ENT CLR Figure 3-1. Front Panel 100 - 240~ 50/60 Hz Console Port 25 Watts, 250 mA max 115 Volt operation - T1A fuses 230 Volt operation - T0.5A fuses RS232 RS 422 (EIA 530) Remote Control B IP Interface 10/100 BaseT V.
PAGE 45
CiM-550 IP Enabled Satellite Modem Operation Rev. 2 CD/CIM550.IOM 3.1.5 WEB SERVER OPERATION The CiM-550 modem provides an embedded web server application that serves standard HTML web pages that can be used to monitor and control all CiM-550 modem and IP parameters. These web pages have been designed for optimal performance when using MicroSoft’s Internet Explorer version 5 or higher. Access to this application is provided via the 10/100 Base T IP interface (RJ-45).
PAGE 46
CiM-550 IP Enabled Satellite Modem Operation Rev. 2 CD/CIM550.
PAGE 47
Chapter 4. Front Panel Menus Front Panel Operation 21 Keypad 21 Menu Tree 23 Menu Screens 27 4.1 FRONT PANEL OPERATION The user can fully control and monitor the operation of the CiM-550 modem from the front panel, using the keypad and display. Nested menus are used, which display all available options, and prompt the user to carry out a required action. The display has two lines each of 24 characters.
PAGE 48
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM Key Function RIGHT ARROW Moves the cursor to the right, when it is displayed. LEFT ARROW Moves the cursor to the left, when it is displayed. UP ARROW Used for editing the value at the current cursor position, if appropriate. If this is a numeric field, this will increment the value. DOWN ARROW Used for editing the value at the current cursor position, if appropriate.
PAGE 49
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.3 LED INDICATORS There are 8 LED indicators. The functions of these indicators are shown in the table below. Table 4-1.
PAGE 50
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM CIM-550 Front Panel Menu Tree 1 of 3 COMTECH CIM-550 MODEM SN 700000007 VER 1.22 PRESS ANY KEY SELECT: CONFIG TEST INFO MONIT STORE/LD UTIL ODU CONFIGURE ALL TX RX FRAME INTFC REMCONT MASK IMPED ALL TAKES USER THROUGH COMPLETE CONFIGURATION TX MOD FREQ DATA FEC ON/OFF PWR SCRAM CLK TSI TEST NORM TX-CW TX-1,0 IF DIG I/O RF INFO* MONIT* STORE/LD** UTIL** ODU** *CONT. ON PAGE 2 **CONT.
PAGE 51
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM CIM-550 Front Panel Menu Tree 2 of 3 COMTECH CIM-550 MODEM SN 700000007 VER 1.22 INFO ALL TX RX BUFF MASK EDMAC ID FW MISC FAST PRESS ANY KEY SELECT: CONFIG TEST INFO MONIT STORE/LD UTIL ODU ALL ON OFF RTI TX Tx: 70. 000 1024. 000 VI T B R1/ 2 S I NT - 20. 0 RTI N RX Rx: 70.0001024.000VIT BR1/2 DNBUF+/-10.
PAGE 52
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM CIM-550 Front Panel Menu Tree 3 of 3 COMTECH CIM-550 MODEM SN 700000007 VER 1.
PAGE 53
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.5 MENU SCREENS 4.1.5.1 OPENING SCREEN DISPLAY COMTECH CiM-550 MODEM S/N 1209 S/W VER 1.22 SELECTIONS/DESCRIPTION This is an example of the Opening Screen. Refer to CDM-550 Manual for correct version information. This screen is displayed whenever power is first applied to the unit. Pressing any key will take the user to the top level selection screen. 4.1.5.
PAGE 54
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.5.2.1 SELECT\CONFIG DISPLAY CONFIG: ALL TX RX FRAME INTFC REMCONT MASK IMPED SELECTIONS/DESCRIPTION ALL TX RX The ALL menu sub-branch permits the user to completely configure the unit, being prompted, step by step, to make choices, or edit data. This is highly recommended for new users, as it will clearly demonstrate all the parameters which need to be set.
PAGE 55
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM SELECT\CONFIG\TX\DATA RATE DISPLAY SELECTIONS/DESCRIPTION EDIT TX DATA RATE: 2048.000 kbps(PRESS ENT) Select the digit to be edited. Change the value of the digit using the UP/DOWN arrow keys, then press ENTER. The overall range of data rates is from 2.4 to 2048 kbps. Note: The minimum and maximum data rates are dependent on modulation type and FEC encoder rate.
PAGE 56
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM SELECT\CONFIG\TX\ON-OFF DISPLAY SELECTIONS/DESCRIPTION SELECT TX OUTPUT STATE: ON OFF RTI (ENTER) ON OFF RTI* * NEW FEATURE RTI means RECEIVE/TRANSMIT INHIBIT. When selected, it will prevent the TX carrier from being transmitted, until the demodulator is locked.
PAGE 57
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM SELECT\CONFIG\TX\PWR DISPLAY SELECTIONS/DESCRIPTION OUTPUT POWER LEVEL MODE: MANUAL AUPC (ENTER) EDIT OUTPUT POWER LEVEL: -20.0 dBm (PRESS ENTER) WARNING! AUTO UPLINK PWR CONTRL NEEDS FRAMED MODE TARGET Eb/No MAX RANGE ALARM DEMOD-UNLOCK(ENT) MANUAL AUPC MANUAL display screen Default value is 3.0 dB, and upper limit is 9.9 dB AUPC warning screen is shown if ‘Framed Mode’ is not selected. See SELECT-CONFIG-FRAME menu.
PAGE 58
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM ACTION WHEN REMOTE DEMOD UNLOCKS: NOM-PWR MAX-PWR DEMOD UNLOCK screen Select the action that will occur if the remote demod is unlocked. NOM-PWR MAX-PWR SELECT\CONFIG\TX\SCRAM DISPLAY SELECTIONS/DESCRIPTION When Transparent mode is selected, a V.35 scrambler is used. In Framed or Reed-Solomon modes, a frame synchronized scrambler is used.
PAGE 59
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM SELECT\CONFIG\TX\TSI DISPLAY SELECTIONS/DESCRIPTION SELECT TRANSMIT SPECTRAL INVERSION: OFF ON(ENTER) TSI - Transmit Spectral Interval ON OFF When in the ON position, and QPSK is selected, the transmit spectrum is inverted (which is the same as reversing the direction of phase rotation in the modulator).
PAGE 60
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM SELECT\CONFIG\RX\DATA DISPLAY EDIT RX DATA RATE: 64.000 kbps (PRESS ENT) SELECTIONS/DESCRIPTION The range is 2.4 to 2048 kbps. Note: The minimum and maximum data rates are dependent on modulation type and FEC decoder rate. If the user changes the modulation or FEC, and the currently selected data rate is then invalid, it will be adjusted automatically.
PAGE 61
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM SELECT\CONFIG\RX\ACQ DISPLAY EDIT RX ACQ SWEEP RANGE: +/- 25 kHz (PRESS ENTER) SELECTIONS/DESCRIPTION The range is +/- 1 kHz to +/- 30 kHz. The value entered here determines the amount of frequency uncertainty the demodulator will sweep over in order to find and lock to an incoming carrier. When operating at low bit rates, large values of sweep range (compared to the data rate) will cause excessively long acquisition times.
PAGE 62
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM SELECT\CONFIG\RX\BUF DISPLAY EDIT RX BUFFER SIZE: +/-4096 BITS (PRESS ENT) SELECTIONS/DESCRIPTION Edit the size, in bits of the Plesiochronous/Doppler Buffer. Values of +/- 256, 512, 1024, 2048 and 4096 bits are possible. If the buffer is disabled, a warning message will be displayed if this screen is entered.
PAGE 63
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.5.2.3 SELECT\CONFIG\FRAME DISPLAY SELECT FRAMING MODE: TRANSPARENT FRAMED (ENT) SELECTIONS/DESCRIPTION TRANSPARENT - No framing is selected. No overhead is added, and the unit will be compatible with other manufacturer’s equipment, when operating in a ‘standard’ configuration (IESS 308 filtering, V.35 scrambling, Viterbi).
PAGE 64
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM EDIT THIS UNIT'S ADDRESS 0245 (SEE HANDBOOK)(ENT) (FRAMED/ON) EDMAC SLAVE The valid range of addresses is from 1 to 9999, although ‘base 10' values will be automatically skipped. Remember that this is a unit which is intended to be located at the distant-end of a link, and will therefore be under the control of a MASTER at the other end.
PAGE 65
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.5.2.5 SELECT\CONFIG\REMCONT DISPLAY SELECT REMOTE CONTROL: LOCAL REMOTE (PRESS ENT) SELECTIONS/DESCRIPTION LOCAL REMOTE If LOCAL is selected then remote control will be disabled. Remote monitoring is still possible.
PAGE 66
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.5.2.
PAGE 67
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM SELECT\CONFIG\MASK\BUF-SLIP DISPLAY SEL BUF-SLIP ALARM MASK: ACTIVE MASKED(PRESS ENT) SELECTIONS/DESCRIPTION ACTIVE - If the user selects ACTIVE, then a Receive Traffic fault will be generated whenever the receive circuitry senses that the buffer has either underflowed, or overflowed. MASKED - If the user selects MASKED, no alarm will be generated.
PAGE 68
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM TX-1,0 (Transmit an alternating 1,0,1,0 pattern) This is a test mode which forces the modulator to transmit a carrier modulated with an alternating 1,0,1,0 pattern, at the currently selected symbol rate. This causes two discrete spectral lines to appear, spaced at +/- half the symbol rate, about the carrier frequency. This mode is used to check the carrier suppression of the Modulator.
PAGE 69
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM Figure 4-4.
PAGE 70
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.6 SELECT\INFO DISPLAY INFO:ALL TX RX BUFF MASK EDMAC ID FW MISC FAST SELECTIONS/DESCRIPTION ALL TX RX BUFF MASK EDMAC ID FW MISC FAST 4.1.6.1 SELECT\INFO\TX DISPLAY SELECTIONS/DESCRIPTION Tx:140.0000 2048.000 VIT Q R1/2 S LOP -20.
PAGE 71
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.6.2 SELECT\INFO\RX DISPLAY SELECTIONS/DESCRIPTION Rx: 70.0000 512.
PAGE 72
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.6.4 SELECT\INFO\MASK DISPLAY ALARMS MASKED: RX-AIS SELECTIONS/DESCRIPTION TX-AIS This shows, in the same format as the CONFIG, MASK sub menu, which alarms are currently masked. If an alarm is not masked, a blank is displayed in the relevant screen position. 4.1.6.
PAGE 73
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.6.8 SELECT\INFO\MISC DISPLAY MISC: NORMAL 1:1 LINK=IDLE 50 OHMS ONLINE SELECTIONS/DESCRIPTION This screen shows the following: Test mode IF impedance 1:1 link status - if the CRS-100 1:1 module is being used, this shows the status of the serial link between the two units. Redundancy status - either online or standby (1:1 or 1:N) 4.1.
PAGE 74
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.7.1.2 SELECT\MONIT\ALARMS\RECEIVE DISPLAY RX TRAFFIC: AGC ALARM REDUCE COMPOSITE I/P LVL SELECTIONS/DESCRIPTION The screen will indicate if there are any Receive Traffic Faults. If not, it will display ‘NONE’. 4.1.7.1.3 SELECT\MONIT\ALARMS\TRANSMIT DISPLAY TX TRAFFIC: NO CLOCK DETECTED FROM INTERFACE SELECTIONS/DESCRIPTION The screen will indicate if there are any Transmit Traffic Faults. If not, it will display ‘NONE’. 4.1.
PAGE 75
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.7.3 SELECT\MONIT\STORED-EVENTS DISPLAY STORED EVENTS: VIEW CLEAR ALL (PRESS ENTER) SELECTIONS/DESCRIPTION VIEW CLEAR ALL 4.1.7.3.1 SELECT\MONIT\EVENTS\VIEW DISPLAY LOG23: 30/11/97 10:37:32 FT - DEMOD LOCK (UP/DWN) SELECTIONS/DESCRIPTION The event log can store up to 100 events. When a fault condition occurs, it is time-stamped and put into the log. Similarly, when the fault condition clears, this is also recorded, as shown.
PAGE 76
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.7.4 SELECT\MONIT\STATS DISPLAY LINK STATISTICS: VIEW CLEAR CONFIGURE (ENTER) SELECTIONS/DESCRIPTION VIEW CLEAR CONFIGURE 4.1.7.4.1 SELECT\MONIT\STATS\VIEW DISPLAY STA198:02/11/00 10:37:32 16.0,16.0,9.0,9.0(UP/DN) SELECTIONS/DESCRIPTION VIEW CLEAR ALL The user may scroll backwards or forwards through the entries in the statistics log, using the UP/DOWN arrow keys. The event log can store up to 250 events.
PAGE 77
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM Examples: 08.0,13.5,2.5,1.8 means: Minimum Eb/No observed in the measurement interval = 8.0 dB Average Eb/No observed in the measurement interval = 13.5 dB Maximum TPLI observed in the measurement interval = 2.5 dB Average TPLI observed in the measurement interval = 1.8 dB LOSS,04.5,0.0,0.0 means: There was a loss of demod lock during the measurement interval Average Eb/No observed in the measurement interval = 4.
PAGE 78
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.8 SELECT\STORE\LD DISPLAY STORE/LOAD CONFIG: STORE LOAD (PRESS ENTER) SELECTIONS/DESCRIPTION STORE LOAD These sub-menus permit the user to store or load up to 10 different modem configurations in the nonvolatile memory of the modem 4.1.8.
PAGE 79
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM WARNING! LOC 10 CONTAINS NO DATA! (ENTER) 4.1.9 SELECT\UTIL DISPLAY UTILITY: SET-RTC DISPLAY MAN-1:1 RECENTER-BUF ID SELECTIONS/DESCRIPTION SET-RTC VFD ID MAN-1:1 CENTER-BUF FAST 4.1.9.1 SELECT\UTIL\ \RTC DISPLAY EDIT REAL TIME CLOCK: 12:00:00 24/04/98 (ENT) SELECTIONS/DESCRIPTION Edit the time and date settings of the real-time clock. This is accomplished by selecting the digit to be edited, using the LEFT/RIGHT arrow keys.
PAGE 80
CiM-550 IP Enabled Satellite Modem Front Panel Menus Rev. 2 CD/CIM550.IOM 4.1.9.4 SELECT\UTIL\RECENTER-BUF DISPLAY PRESS ENTER TO RE-CENTER THE RECEIVE BUFFER SELECTIONS/DESCRIPTION Pressing ENTER will cause a forced re-centering of the Plesiochronous/Doppler buffer. 4.1.9.5 SELECT\UTIL\ID DISPLAY EDIT CIRCUIT ID: (ENTER) THIS IS A TEST MESSAGE SELECTIONS/DESCRIPTION Only the bottom line is available (24 characters).
PAGE 81
Chapter 5. Serial Remote Control EIA-485 55 EIA-232 56 Basic Protocol 56 Packet Structure 57 5.1 INTRODUCTION This section describes the protocol and message command set for remote monitor and control of the CiM-550 Modem. The electrical interface is either an EIA-485 multi-drop bus (for the control of many devices) or an EIA-232 connection (for the control of a single device), and data is transmitted in asynchronous serial form, using ASCII characters.
PAGE 82
CiM-550 IP Enabled Satellite Modem Serial Remote Control Rev. 2 CD/CIM550.IOM EIA 485 (full duplex) summary: Two differential pairs - one pair for controller to target, one pair for target to controller. Controller-to-target pair has one line driver (controller), and all targets have linereceivers. Target-to-controller pair has one line receiver (controller), and all targets have tristate drivers. 5.
PAGE 83
CiM-550 IP Enabled Satellite Modem Serial Remote Control Rev. 2 CD/CIM550.IOM 5.5 PACKET STRUCTURE Controller-to-target: Start of Packet Target Address Address De-limiter < ASCII code 60 (1 character) Instructio n Code / ASCII code 47 (4 characters) Example: (1 character) Code Qualifier Optional Arguments = or ? ASCII code 61 or 63 (3 characters) (1 character) End of Packet Carriage Return ASCII code 13 (1 character) (n characters) <0135/TFQ=70.
PAGE 84
CiM-550 IP Enabled Satellite Modem Serial Remote Control Rev. 2 CD/CIM550.IOM 5.5.3 INSTRUCTION CODE This is a three-character alphabetic sequence which identifies the subject of the message. Wherever possible, the instruction codes have been chosen to have some significance. For example TFQ for transmit frequency, RMD for receive modulation type, etc. This aids in the readability of the message, should it be displayed in its raw ASCII form.
PAGE 85
CiM-550 IP Enabled Satellite Modem Serial Remote Control Rev. 2 CD/CIM550.IOM 2) From Target to Controller, the only permitted values are: = (ASCII code 61) ? (ASCII code 63) ! (ASCII code 33) * (ASCII code 42) They have these meanings: The ‘=’ code (target to controller) is used in two ways: First, if the controller has sent a query code to a target (for example TFQ?, meaning ‘what’s the Transmit frequency?’), the target would respond with TFQ=xxx.xxxx, where xxx.
PAGE 86
CiM-550 IP Enabled Satellite Modem Serial Remote Control Rev. 2 CD/CIM550.IOM 5.5.5 MESSAGE ARGUMENTS Arguments are not required for all messages. Arguments are ASCII codes for the characters 0 to 9 (ASCII 48 to 57), period (ASCII 46) and comma (ASCII 44). 5.5.6 END OF PACKET Controller to Target: This is the ‘Carriage Return’ character (ASCII code 13) Target to Controller: This is the two-character sequence ‘Carriage Return’, ‘Line Feed’. (ASCII code 13, and code 10.
PAGE 87
CiM-550 IP Enabled Satellite Modem Remote Control Rev. 2 CD/CIM550.IOM Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) Query (Instruction Code and qualifier) Response to query (target to controller) Tx Frequency TFQ= 8 bytes Command or Query.
PAGE 88
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.
PAGE 89
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.IOM Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) 1 = Tx Spectrum Inverted All other codes invalid.
PAGE 90
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.IOM Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) 2 = Off due to ext H/W Tx Carrier Off command (not a valid argument when used as a command) All other codes invalid.
PAGE 91
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.
PAGE 92
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.IOM Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) 0 = Normal 1 = Rx Spectrum Inverted All other codes invalid.
PAGE 93
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.
PAGE 94
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Mode Rev. 2 CD/CIM550.IOM Arguments for Command or Response to Query Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) 0,1,2,3,4 or 5 1 = IF loopback 2 = Digital loopback 3 = I/O loopback 4 = Tx CW 5 = Tx Alternating 1,0 pattern All other codes invalid.
PAGE 95
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.IOM Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) Query (Instruction Code and qualifier) Response to query (target to controller) define the unit as being an EDMAC Master. This command is only valid for an EDMAC master.
PAGE 96
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.
PAGE 97
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.
PAGE 98
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.
PAGE 99
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.IOM Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) Query (Instruction Code and qualifier) Response to query (target to controller) FSW= (message ok) N/A N/A This command takes no arguments.
PAGE 100
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.IOM Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) Query (Instruction Code and qualifier) Response to query (target to controller) 127 starting at address location 104.
PAGE 101
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Interval Rev. 2 CD/CIM550.IOM Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) SSI=x, where x = 0 to 9 in 10 minute steps. Note: setting this parameter to 0 disables the statistics logging function.
PAGE 102
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.IOM Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) Query (Instruction Code and qualifier) Response to query (target to controller) than 5 events to be retrieved, the remaining positions are padded with zeros.
PAGE 103
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.IOM Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) Query (Instruction Code and qualifier) Response to query (target to controller) affect this value. Example reply: NUS=198 Rx Eb/No N/A 4 bytes, numerical Query only.
PAGE 104
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.IOM Description of arguments (note that all arguments are ASCII numeric codes, that is, ASCII codes between 48 and 57) Response to Command (target to controller) Query (Instruction Code and qualifier) 0 = Off Line (forced into standby by 1:N or 1:1 Switch) 1= On Line (normal). All other codes invalid.
PAGE 105
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.
PAGE 106
CiM-550 IP Enabled Satellite Modem Remote Control Parameter Type Command (Instruction Code and qualifier) Arguments for Command or Response to Query Rev. 2 CD/CIM550.
PAGE 107
Chapter 6. Theory of Operation Functional Description 81 Offset QPSK Operation 82 EIA-232 Operation 83 AUPC (Automatic Uplink Power Control) 88 6.1 FUNCTIONAL DESCRIPTION The CiM-550 has two fundamentally different types of interface - IF and data. The data interface is a bi-directional path which connects with the customer’s equipment (assumed to be the DTE) and the modem (assumed to be the DCE).
PAGE 108
CiM-550 IP Enabled Satellite Modem Theory of Operation Rev. 2 CD/CIM550.IOM After decoding, the recovered clock and data pass to the de-framer (if EDMAC is enabled) where the overhead information is removed. Following this, the data passes to the Plesiochronous/Doppler buffer, which has a programmable size, or may be bypassed. From here, the receive clock and data signals are routed to the terrestrial interface, and are passed to the externally connected DTE equipment. 6.
PAGE 109
CiM-550 IP Enabled Satellite Modem Theory of Operation Rev. 2 CD/CIM550.IOM 6.3 EIA-232 OPERATION The CiM-550 supports asynchronous EIA-232 in addition to synchronous EIA-232 formats. This is useful, for example, in connecting two computers together, via their serial ports, at opposite ends of a satellite link. There are, however, some restrictions and limitations when using this mode, and the user may have to experiment a little in order to get reliable communication. 6.3.
PAGE 110
CiM-550 IP Enabled Satellite Modem Theory of Operation Rev. 2 CD/CIM550.IOM 6.3.2.2 ASYNC CHARACTER FORMATS USING 1.5 STOP BITS For situations where an async character format using 1.5 stop bits cannot be avoided, set the modem data rate to exactly twice the incoming baud rate. This uses twice as much bandwidth, but will permit this mode of operation. 6.3.3 CLOCKING When dealing with satellite modems, the subject of clocking can be a complex issue.
PAGE 111
CiM-550 IP Enabled Satellite Modem Theory of Operation Rev. 2 CD/CIM550.IOM 6.3.3.2 RECEIVE CLOCKING There are three receive clocking modes in the CiM-550. 6.3.3.2.1 Buffer Disabled When the buffer is disabled, the receive clock (Receive Timing, or RT) is derived directly from the demodulator, and hence will be subject to plesiochronous and Doppler offsets.
PAGE 112
CiM-550 IP Enabled Satellite Modem Theory of Operation Rev. 2 CD/CIM550.IOM 6.3.4 TRANSMIT AND RECEIVE CLOCKING INTERNAL TX CLOCK MODE DATA TO MODULATOR CIRCUIT TX DATA PLL CIRCUIT TX FIFO TX CLO CK (TT ) CLOCK VCXO TRANSMIT DATA INTERFACE DIRECT DIGITAL SNTHESIZER INT ERNAL CLO CK (ST ) 14.
PAGE 113
CiM-550 IP Enabled Satellite Modem Theory of Operation Rev. 2 CD/CIM550.
PAGE 114
CiM-550 IP Enabled Satellite Modem Theory of Operation Rev. 2 CD/CIM550.IOM 6.4 AUPC (AUTOMATIC UPLINK POWER CONTROL) Automatic Uplink Power Control (AUPC) is a feature whereby a local modem is permitted to adjust its own output power level in order to attempt to maintain the Eb/No at the remote modem. IMPORTANT NOTICE The user MUST obtain permission from the Satellite Operator to use this feature.
PAGE 115
CiM-550 IP Enabled Satellite Modem Theory of Operation Rev. 2 CD/CIM550.IOM 6.4.1.1 TARGET EB/NO This is value of Eb/No that the user desires to keep constant at the remote modem. If the Eb/No exceeds this value, the AUPC control will reduce the TX output power, but will never drop below the nominal value set. If the Eb/No falls below this value, the AUPC control will increase the TX output power, but will never exceed the value determined by the parameter MAX RANGE.
PAGE 116
CiM-550 IP Enabled Satellite Modem Theory of Operation Rev. 2 CD/CIM550.IOM 6.4.2 COMPENSATION RATE As with any closed-loop control system, the loop parameters must be chosen to ensure stability at all times. Several features have been incorporated to ensure that the AUPC system does overshoot, or oscillate. First, the rate at which corrections to the output power can be made is fixed at once every 4 seconds.
PAGE 117
Chapter 7. Forward Error Correction Options Viterbi 91 Sequential 92 TURBO Product Codec 93 Uncoded Operation 96 7.1 INTRODUCTION As standard, the CiM-550 Modem is equipped with two Forward Error Correction Decoders, Viterbi and Sequential. The constraint lengths and encoding polynomials are compatible with the vast majority of existing modems from other manufacturers, and Comtech EF Data has performed compatibility testing to ensure inter-operability.
PAGE 118
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM A choice of coding rates (Rate 1/2, 3/4 or 7/8) allows the user to trade off coding gain for bandwidth expansion. Rate 1/2 coding gives the best improvement in error rate, but doubles the transmitted data rate, and hence doubles the occupied bandwidth of the signal. Rate 7/8 coding, at the other extreme, provides the most modest improvement in performance, but only expands the transmitted bandwidth by 14 %.
PAGE 119
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM A fixed computational clock is used to process input symbols, and to search backwards and forwards in time to determine the correct decoding path. At lower data rates there are sufficient number of computational cycles per input symbol to permit the decoding process to perform optimally. However, as the data rate increases, there are fewer cycles available, leading to a reduction in coding gain.
PAGE 120
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM When Comtech EF Data first introduced the Turbo Coding option in the CiM-550, only Rate 3/4 QPSK was offered. This is an excellent choice for applications where maximum bandwidth efficiency is desired, in combination with high coding gain. However, with Firmware Version 1.15 (and later) Comtech EF Data has introduced two further code rates - Rate 21/44 BPSK (very close to Rate 1/2) and Rate 5/16 BPSK (very close to Rate 1/3).
PAGE 121
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM FEC Mode (64 kbps data rate) End-to-end delay, ms Viterbi, Rate 1/2 12 Sequential, Rate 1/2 74 Turbo Product Coding, Rate 3/4, QPSK 79 Turbo Product Coding, Rate 21/44, BPSK 64 Turbo Product Coding, Rate 5/16, BPSK 48 Note: In all cases, the delay is inversely proportional to data rate, so for 128 kbps, the delay values would be half of those shown above.
PAGE 122
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM 7.5 UNCODED OPERATION (NO FEC) IMPORTANT COMTECH EFDATA CANNOT BE HELD RESPONSIBLE FOR INCORRECT OPERATION IF THE USER DOES NOT ADHERE TO THESE GUIDELINES WHEN USING UNCODED OPERATION. There are occasions where a user may wish to operate a satellite link with no forward error correction of any kind. For this reason, the CiM-550 offers this uncoded mode for all three modulation types - BPSK, QPSK and OQPSK.
PAGE 123
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM In order to accomplish the task of carrier recovery, the demodulator must use a non-linear process. A second-order non-linearity is used for BPSK, and a fourth-order non-linearity is used for QPSK. When data at a certain symbol rate is used to modulate the carrier, the demodulator can lock at incorrect frequencies, spaced at intervals of one-quarter of the symbol rate away from the carrier.
PAGE 124
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM Eb/No in dB 1 2 3 4 5 6 7 8 9 10 11 12 1E-1 Uncoded BPSK/QPSK 1E-2 Viterbi Decoding Typical Performance 1E-3 1E-4 1E-5 1E-6 Specification limit, Rate 7/8 Coding 1E-7 1E-8 Specification limit, Rate 3/4 Coding Specification limit Rate 1/2 Coding 1E-9 1 2 3 4 5 6 7 BER Figure 7-1.
PAGE 125
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM Eb/No in dB 1 2 3 4 5 6 7 8 9 10 11 12 1E-1 Uncoded BPSK/QPSK Sequential Decoding 64 kbps 1E-2 Typical Performance 1E-3 1E-4 1E-5 1E-6 Specification limit, Rate 7/8 Coding 1E-7 1E-8 Specification limit Rate 1/2 Coding 1E-9 1 2 3 4 Specification limit, Rate 3/4 Coding 5 6 7 8 BER Figure 7-2.
PAGE 126
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM Eb/No in dB 1 2 3 4 5 6 7 8 9 10 11 12 1E-1 Uncoded BPSK/QPSK Sequential Decoding 1024 kbps 1E-2 1E-3 Typical Performance 1E-4 1E-5 1E-6 Specification limit, Rate 7/8 Coding 1E-7 1E-8 Specification limit Rate 1/2 Coding 1E-9 1 2 3 4 Specification limit, Rate 3/4 Coding 5 6 7 8 BER Figure 7-3.
PAGE 127
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM Eb/No in dB 1 2 3 4 5 6 7 8 9 10 11 12 1E-1 Uncoded BPSK/QPSK Sequential Decoding 2048 kbps 1E-2 1E-3 1E-4 1E-5 1E-6 Typical performance, Rate 7/8 Coding 1E-7 1E-8 Typical performance, Rate 3/4 Coding Typical performance, Rate 1/2 Coding 1E-9 1 2 3 4 5 6 7 8 BER Figure 7-4.
PAGE 128
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM Eb/No in dB 1 2 3 4 5 6 7 8 9 10 11 12 1E-1 Comtech Turbo Product Codec Rate 3/4 QPSK Rate 21/44 BPSK Rate 5/16 BPSK Uncoded BPSK/QPSK 1E-2 Specification limit - Rate 21/44 BPSK Specification limit - Rate 3/4 QPSK 1E-3 Specification limit - Rate 5/16 BPSK 1E-4 1E-5 1E-6 1E-7 Typical performance is approximately 0.3 dB better than shown 1E-8 1E-9 1 2 3 4 5 6 7 8 9 BER Figure 7-5.
PAGE 129
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.IOM Eb/No in dB 1 2 3 4 5 6 7 8 9 10 11 12 1E-1 1E-2 Differential Encoding No FEC Uncoded BPSK/QPSK 1E-3 1E-4 1E-5 1E-6 1E-7 1E-8 1E-9 1 2 3 4 5 6 7 8 BER Figure 7-6.
PAGE 130
CiM-550 IP Enabled Satellite Modem Forward Error Correction Rev. 2 CD/CIM550.
PAGE 131
Chapter 8. EDMAC CHANNEL Theory Of Operation 105 M&C Connection 107 Setup Summary 108 8.1 THEORY OF OPERATION As explained earlier, EDMAC is an acronym for Embedded Distant-end Monitor And Control. This is a feature which permits the user to access the M&C features of modems which are at the distant-end of a satellite link. This is accomplished by adding extra information to the user’s data, but in a manner which is completely transparent to the user. 8.1.
PAGE 132
CiM-550 IP Enabled Satellite Modem EDMAC Rev. 2 CD/CIM550.IOM Adding the extra 5% to the transmitted data rate, the effective Eb/No seen by the user will degrade by a factor of 10log(1.05), or 0.21 dB (0.07dB in the case of the two BPSK Turbo rates). The use of an externally synchronized scrambler and descrambler almost exactly compensates for this degradation. The net effect is that the user will see effectively identical BER performance whether framing is used or not. 8.1.
PAGE 133
CiM-550 IP Enabled Satellite Modem EDMAC Rev. 2 CD/CIM550.IOM 8.2 M&C CONNECTION Data to be transmitted to the distant-end is sent to a local unit via the remote control port. A message for the distant-end is indistinguishable from a ‘local’ message - it has the same structure and content, only the address will identify it as being for a distant-end unit. Before the M&C data can be successfully transmitted and received, pairs of units must be split into EDMAC Masters and EDMAC Slaves.
PAGE 134
CiM-550 IP Enabled Satellite Modem EDMAC Rev. 2 CD/CIM550.IOM 8.3 SETUP SUMMARY To access a distant-end unit: Designate a Master/Slave pair - Master at the local-end, Slave at the distant-end. On the local-end unit, enable framing, and EDMAC, define the unit as MASTER, then enter the bus address of the SLAVE. This is constrained to be ‘base 10' meaning that only addresses such as 10, 20, 30, 40 etc, are allowed. Choose a unique bus address for the distant-end.
PAGE 135
Chapter 9. Eb/No Measurement 9.1 MEASURING EB/NO Although the CiM-550 calculates and displays the value of receive Eb/No on the front panel of the unit, it is sometimes useful to measure the value using a spectrum analyzer, if one is available.
PAGE 136
CiM-550 IP Enabled Satellite Modem Eb/No Notes: Rev. 2 CD/CIM550.IOM (C+N)/N Eb/No Uncoded BPSK Eb/No Rate 1/2 BPSK Eb/No Uncoded QPSK Eb/No Rate 1/2 QPSK Eb/No Rate 3/4 QPSK Eb/No Rate 7/8 QPSK 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 7.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 12.0 12.5 13.0 13.5 14.0 14.5 15.0 15.5 16.0 16.5 17.0 17.5 18.0 0.0 0.9 1.8 2.6 3.3 4.1 4.7 5.4 6.0 6.6 7.3 7.8 8.4 9.0 9.5 10.1 10.6 11.2 11.7 12.2 12.8 13.3 13.8 14.3 14.9 15.4 15.9 16.4 16.9 17.4 17.9 3.0 3.9 4.8 5.6 6.3 7.
PAGE 137
Chapter 10. Connector Pinouts Data Connector 111 Alarms Connector 112 Remote Control Connector 113 Auxiliary Serial Connector 113 100 - 240~ 50/60 Hz Console Port 25 Watts, 250 mA max 115 Volt operation - T1A fuses 230 Volt operation - T0.5A fuses RS232 RS 422 (EIA 530) Remote Control B IP Interface 10/100 BaseT V.35 COMTECH EF DATA CORP MADE IN THE USA SN Date 2001 Receive IF Console Port Data Interface Alarms Aux Serial Remote Control A Transmit IF Figure 10-1. Rear Panel 10.
PAGE 138
CiM-550 IP Enabled Satellite Modem Connector Pinouts Rev. 2 CD/CIM550.IOM Pin Generic Signal Description Direction EIA-422/ EIA 530 V.35 EIA-232 Circuit No 17 Receive Clock A Modem to DTE RT A SCR A DD 115 23 External Carrier Off (EIA-232 ‘1' or TTL ‘low’ ) DTE to Modem - - - - 24 Transmit Clock A DTE to Modem TT A SCTE A DA 113 Notes: 1 Receiver ready is an EIA-232-level control signal on a V.35 interface.
PAGE 139
CiM-550 IP Enabled Satellite Modem Connector Pinouts Rev. 2 CD/CIM550.IOM 10.3 REMOTE CONTROL CONNECTOR - 9 PIN ‘D’ TYPE MALE Table 10-3. Remote Control Connector - 9 Pin ‘D’ Type Male Pin Description 1 Ground 2 EIA-232 Transmit Data (Out) 3 EIA-232 Receive Data 4 Reserved - do not connect to this pin 5 Ground 6 EIA-485 Receive Data B (In) 7 EIA-485 Receive Data A (In) 8 EIA-485 Transmit Data B (Out) 9 EIA-485 Transmit Data A (Out) (In) 10.
PAGE 140
CiM-550 IP Enabled Satellite Modem Connector Pinouts Rev. 2 CD/CIM550.IOM 10.5 ASYNC-SERIAL CONSOLE The Console Connector is a RJ11-6 modular jack located on the rear panel. The AsyncSerial Console interfaces the IP Telnet Configuration Port. This interface is a EIA-232 DCE interface. Table 10-5. Async-Serial Console RJ11-6 Pin Function 1 Ground 2 Rx 3 Tx 4 Ground 5 No used 6 Not used 10.
PAGE 141
Chapter 11. CLI and Telnet Interface Overview 115 Main Menu Page 116 Administration Page 118 SMTP 127 SNMP 128 Interface Configuration Page 130 Receiver HDLC Addresses Page 134 Route Table Configuration Page 135 Protocol Configuration Page 142 Modem Parameters Page 148 Redundancy Configuration Page 158 Operations and Maintenance Page 161 11.1 OVERVIEW This section defines the user menu system presented to a user connected to the CiM via a Terminal Emulator or telnet.
PAGE 142
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2 MAIN MENU PAGE Menu pages are followed by a table listing the Menu Options/Fields, required Entry, and Descriptions. The Main Menu page has the following options/fields: Menu Options/Fields Entry Description Administration A The Administration menu provides a basic set of standard admin functions to the CiM. When connected via telnet, navigation to this menu will be restricted to the admin user.
PAGE 143
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description Save Parameters S This option allows a user to save the current configuration of the CiM to permanent storage. This configuration will be restored on each successive power cycle of the CiM. Exit X This option allows a user to exit the current menu and return to its parent menu.
PAGE 144
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.1 ADMINISTRATION PAGE The Administration page is activated from the Main Menu page. Note: Access to the Administration page is restricted to the Admin user when connecting via the telnet interface. The Administration page is available to all users when connected via the Terminal Emulator (serial) connection. The Administration page contains the following options/fields.
PAGE 145
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Exit Rev. 2 CD/CIM550.IOM Entry X Description This option allows a user to exit the current menu and return to its parent menu. 11.2.1.1 NAME/PASSWORD CONFIGURATION PAGE The Name/Password Configuration page is activated from the Administration page. This option allows an operator to define the passwords required to access the CiM via telnet, HTML, FTP, SNMP, and TELNET.
PAGE 146
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description Save Parameters S This option allows a user to save the current configuration of the CiM to permanent storage. This configuration will be restored on each successive power cycle of the CiM. Exit X This option allows a user to exit the current menu and return to its parent menu. 11.2.1.
PAGE 147
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.1.3 ACCESS LISTS PAGE The Access Lists page is activated from the Administration page. This page allows the operator to configure the CiM to limit monitor and control access to the unit from a specified list of authorized clients. Note: If connecting to the CiM remotely, the IP address of the machine used to manage the CiM should be included in the Access List.
PAGE 148
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.1.4 FEATURE CONFIGURATION PAGE The Feature Configuration page is activated from the Administration page. The Feature Configuration menu communicates to the user the current availability for each of the features. If a feature is marked “Unavailable” and it has a letter, Transmit DES Encryption for example, then the feature is a FAST feature. FAST features must be purchased from Comtech EF Data.
PAGE 149
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields IGMP Rev. 2 CD/CIM550.IOM Entry I Description Toggles [Enabled] and [Disabled] This feature must be purchased. The receive portion of a CiM will utilize the CiM as an IGMP server. The transmit portion of a CiM will utilize the CiM as an IGMP client. The IGMP Information Page configures the CiM to report an interest to join a Multicast group on an IGMP server.
PAGE 150
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM Menu Options/Fields Entry Description TCP Acceleration Read Only Unavailable Header Compression Read Only Unavailable Unavailable Easy Connect Save Parameters S This option allows a user to save the current configuration of the CiM to permanent storage. This configuration will be restored on each successive power cycle of the CiM.
PAGE 151
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.1.5 DES ENCRYPT CONFIGURATION PAGE The DES Encrypt Configuration page is activated from the Administration page. Note: This menu will only be accessible if the DES FAST feature has been purchased and the license key has been entered through the modem front panel.
PAGE 152
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description The key is entered in HEX (16 digits max) Save Parameters S This option allows a user to save the current configuration of the CiM to permanent storage. This configuration will be restored on each successive power cycle of the CiM. Exit X This option allows a user to exit the current menu and return to its parent menu.
PAGE 153
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.1.6 SMTP The SMTP Configuration page is activated from the Administration page. The SMTP Configuration contains the following options/fields: Menu Options/Fields Entry Description SMTP Server IP Address I Not Defined SMTP Domain D Set to the domain of the email server (usually found to the right of the @ symbol in an email address).
PAGE 154
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.1.7 SNMP The SNMP Configuration page is activated from the Administration page. The SNMP Configuration contains the following options/fields: Menu Options/Fields Entry Description SNMP Admin Get/Set Community Read Only GET and SET community string for Admin user. This community string allows GET/SET operations to all portions of the cimController and cim550 MIBs.
PAGE 155
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description SNMP Stats N Displays statistics concerning the operation of the SNMP agent (number of IN SNMP packets, number of OUT SNMP packets, number of OUT Traps, etc…) Save Parameters S This option allows a user to save the current configuration of the CiM to permanent storage. This configuration will be restored on each successive power cycle of the CiM.
PAGE 156
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.2 INTERFACE CONFIGURATION PAGE The Interface Configuration page is activated from the Main Menu page. The Interface Configuration page contains the following options/fields: Menu Options/Fields Entry Description Ethernet Interface (fei0) E Activates Fast Ethernet page. Satellite/HDLC Interface (hdl1) H Activates Satellite/HDLC Interface page.
PAGE 157
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.2.1 FAST ETHERNET INTERFACE (FEI0) PAGE The Fast Ethernet Interface page is activated from the Interface Configuration page. The Fast Ethernet Interface page contains the following options/fields: Menu Options/Fields Entry Description MAC Address Read Only The MAC Address defines the hardware destination MAC Address that is used when an Ethernet packet is destined for the CiM Ethernet Interface.
PAGE 158
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.2.2 SATELLITE/HDLC INTERFACE (HDL1) PAGE The Satellite/HDLC Interface (hdl1) page is activated from the Interface Configuration page. The Satellite/HDLC Interface page contains the following options/fields: Menu Options/Fields Entry Description IP Address I Specifies the IP Address assigned to the Satellite Interface of the CiM.
PAGE 159
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description Enabled tells the CiM to receive and process packets from the Satellite Interface. Disabled tells the CiM to discard and not process packets from the Satellite Interface. Note: This comment does not disable the modem. TX – Enable/Disable N Toggles [Enabled] and [Disabled] Enabled tells the CiM to allow routing of packets from its Ethernet interface to its Satellite interface.
PAGE 160
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.2.3 RECEIVER HDLC ADDRESSES PAGE The Receiver HDLC Addresses page is activated from the Satellite/HDLC Interface page. This page allows the user to define up to four HDLC addresses that can carry user information on the Satellite Interface.
PAGE 161
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.3 ROUTE TABLE CONFIGURATION PAGE The Route Table Configuration page is activated from the Main Menu page. The Route Table Configuration page contains the following options/fields: Menu Options/Fields Route001-Route008 (The 8 currently displayed routes) Entry 1-8 Description The Route Table allows a user to define how the packets that the CiM receives are routed.
PAGE 162
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description Optionally: If the user enters a multicast address (224.0.0.0-239.255.255.255) as the destination IP address, then the following parameters will be requested: Route MultiCast packets from Ethernet to Satellite? [y/n] The option allows the user to specify if multicast packets that match the provided IP address will be routed from the Ethernet to Satellite.
PAGE 163
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.3.1 QOS (QUALITY OF SERVICE)/DES (ENCRYPTION) PAGE The QoS/DES page is activated from the Route Table Configuration page. The QoS Configuration/DES Key Selection Page allows the user to define rules on how traffic over the Satellite Interface is processed by the CiM. All routes are presented to the user in the form of a table.
PAGE 164
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description packets for a route because of a lack in carrier bandwidth. The Min Bandwidth is entered in multiples of 8 Kbps. Max Bandwidth # The Max bandwidth field establishes a hard maximum traffic rate that can be processed by the CiM before it starts to silently discard traffic. A value of 0 for this field implies that no maximum limit is assigned to a route.
PAGE 165
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description Modem Data Rate is given in true 1K blocks (56K is truly 56Kbps). DES Key # The DES Key field allows the user to specify which DES Key should be selected for a route. This parameter will assume one of (3) values: 1. Clear 2. Key1 3. Key2 4. Random The value of CLEAR will force the CiM to not encrypt any traffic destined for the satellite.
PAGE 166
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.3.1.1 Example Implementations using QoS and QoS Prioritization The combination of MIN and MAX Bandwidth QoS combined with QoS Prioity allows for multiple levels of QoS implementation. We recommend that QoS is configured using one of the following formats: PRIORITY with MAX BW – All routes are configured with the default value of 0 for MIN and can have a MAX BW defined to limit the amount of BW used by a route.
PAGE 167
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM Exit..........................................................................X Route 1 (Vidconf) and Route 2 (VoIP) traffic require that the packets are forwarded with the least amount of latency, so they are designated as Priority 1. Route 1 has a Min B/W of 512 kbps to insure that amount of B/W will always be available for the video traffic. Route 2 is set up similarly with a Min B/W of 384 kbps for VoIP traffic.
PAGE 168
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.4 PROTOCOL CONFIGURATION PAGE The Protocol Configuration page is activated from the Main Menu page. The Protocol Configuration page contains the following options/fields: Menu Options/Fields Entry Description IGMP I Activates IGMP page. ARP A Activates ARP Table Utilities page. Save Parameters S This option allows a user to save the current configuration of the CiM to permanent storage.
PAGE 169
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.4.1 IGMP INFORMATION PAGE The page IGMP information page is activated from the Protocol Configuration page. The IGMP Information page allows a user to view the IGMP clients that are actively listening to content being provided by the CiM. It also allows the user to determine how the Ethernet Interface is configured either to receive requests to join IGMP groups or announce groups for others to join.
PAGE 170
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description CiM as Server: Number of missed responses before leaving IGMP group M Defines the number of membership queries that go unanswered from LAN clients before the Ehternet Interface will no longer forward data for that IGMP group. Consider a CiM that has the IGMP query period set to 60 seconds and the number of missed responses set to 3.
PAGE 171
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description CiM as Client: Force Cisco Router Alert Option sending V1 reports A Some Cisco Routers may require the definition of a Router Alert Option to recognize a report from a Client to join a Multicast group. The IP Router Alert Option is defined in RFC2113 and was introduced by Cisco. While this option is not part of the IGMP standard, most IGMP V2 implementations contain this option.
PAGE 172
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.4.2 ARP TABLE UTILITIES PAGE The ARP Table Utilities page is activated from the Protocol page. The ARP Table Utilities page allows the user to view and edit the ARP table defined by the CiM. It allows up to 1024 static ARP entries. The Static ARP entries provided by the CiM fall into two categories: IP->MAC and IP->HDLC.
PAGE 173
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description IP Address must be a valid Unicast address (Not Multicast, broadcast, etc.) 2. A MAC Address The MAC Address defines the hardware destination MAC Address that is used when an Ethernet packet destined for an IP machine from the CiM.
PAGE 174
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.5 MODEM PARAMETERS PAGE The Modem Parameters page is activated by selecting Satellite Modem Configuration from the Main Menu page. Note: Refer to CDM-550 user manual for detailed explanation of all parameters and settings listed in this menu and sub-menus. This section provides the valid selections available for each menu item.
PAGE 175
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.5.1 TRANSMIT MODEM CONFIGURATION PAGE The Transmit Modem Configuration page is activated from the Modem Parameters page. The Transmit Modem Configuration page contains the following options/fields: Menu Options/Fields Entry Description Transmit Frequency Q Valid ranges are from 52.0000 to 88.0000 MHz Transmit Data Rate D The rate at which the Modem will send traffic over the Satellite Interface.
PAGE 176
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description Carrier C 1 - OFF 2 - ON 3 - RTI Save Parameters S This option allows a user to save the current configuration of the CiM to permanent storage. This configuration will be restored on each successive power cycle of the CiM. Exit X This option allows a user to exit the current menu and return to its parent menu.
PAGE 177
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.5.2 RECEIVE MODEM CONFIGURATION PAGE The Receive Modem Configuration page is activated from the Modem Parameters page. The Receive Modem Configuration Page contains the following options/fields: Menu Options/Fields Entry Description Receiver Frequency Q Valid ranges are from 52.0000 to 88.0000 MHz. Receive Data Rate D Valid ranges are from 2.4000 to 2048.0000 kbps.
PAGE 178
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description configuration will be restored on each successive power cycle of the CiM. Exit X This option allows a user to exit the current menu and return to its parent menu.
PAGE 179
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.5.3 AUPC MODEM CONFIGURATION PAGE The AUPC Modem Configuration page is activated from the Modem Parameters page. The AUPC Modem Configuration page contains the following options/fields: Menu Options/Fields Entry Description 1 - Disabled 2 - Enabled 1 - OFF 2 - ON Framing F AUPC A Target EbNo of Remote Demod(db) E Valid ranges are from 0.1 to16.0 dB Tx Max Increase (dB) D Valid ranges are from 0 to 9 dB.
PAGE 180
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.5.4 MODEM MISCELLANEOUS CONFIGURATION PAGE The Modem Miscellaneous Configuration page is activated from the Modem Parameters page.
PAGE 181
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.5.5 ALARM MASKS MODEM CONFIGURATION PAGE The Alarm Masks Modem Configuration page is activated from the Modem Parameters page.
PAGE 182
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.5.6 MODEM UTILITIES PAGE The Modem Utilities page is activated from the Modem Parameters page.
PAGE 183
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.5.7 MODEM EVENTS PAGE The Modem Events page is activated from the Modem Parameters page.
PAGE 184
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.6 REDUNDANCY CONFIGURATION PAGE The Redundancy Configuration page is activated from the Main Menu page. Note: This page is not accessible unless the modem is properly connected to a Comtech EF Data qualified Redundancy Switch. Figure 11-1.
PAGE 185
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM Redundancy implies the coordination of two CiM’s to provide a redundant link. Each of the CiM’s will be defined as either an Online or Offline. The Online is the unit that will process user traffic. The Offline modem monitors the health of the Online Modem. If the Offline detects a failure on the Online, it will assume the role of the Online.
PAGE 186
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM The Redundancy Configuration page contains the following options/fields: Menu Options/Fields Entry Description Current State Read Only Defines the online/offline status of the CiM. Management IP Address, Local Unit Read Only IP Address for the Ethernet Interface for the Local Unit. The value is set through the Ethernet Interface(fei0) page.
PAGE 187
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.7 OPERATIONS AND MAINTENANCE PAGE The Operations and Maintenance page is activated from the Main Menu page. The Operations and Maintenance page contains the following options/fields: Menu Options/Fields Entry Description Status A Displays status information Unit Information I Displays unit information Boot Image B Determines which version of the CiM firmware will be loaded upon boot-up.
PAGE 188
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Menu Options/Fields Rev. 2 CD/CIM550.IOM Entry Description in permanent storage 2. Image2 - boot the firmware loaded into the second slot in permanent storage Statistics T Activates Statistics Menu page. Database Operations D Activates Administrative Database Operations page. Reset R Allows user to reboot the modem. It has the same logical effect of power-cycling the unit. Diagnostics G Activates Diagnostics page.
PAGE 189
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.7.1 UNIT INFORMATION The Unit Information page is activated from the Operations and Maintenance page.
PAGE 190
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.7.2 STATISTICS PAGE The Statistics Menu page is activated from the Operations and Maintenance page. The Statistics Menu page contains the following options/fields: Menu Options/Fields Entry Description Satellite Transmit Statistics T Displays Statistics for the Satellite Transmitter and allows counters to be reset. IP Routing Statistics R Displays Statistics for IP Routing and allows counters to be reset.
PAGE 191
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.7.2.1 Satellite Transmit Statistics Page The Satellite Transmit Statistics page is activated from the Statistics Menu page. The Satellite Transmit Statistics page displays counts of the number of packets transmitted on each configured Satellite destined route on the CiM. In orders words, all of the routes which have a next hop IP address which is another CiM modem on the other side of the Satellite link.
PAGE 192
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.7.2.2 IP Routing Statistics Page The IP Routing Statistics page is activated from the Statistics Menu page The IP Routing Statistics page displays the statistics for the number of IP packets routed by the CiM.
PAGE 193
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM Menu Options/Fields Entry Description Multicast IP Packets routed to Sat Read Only The Multicast Packets routed to Sat counter indicates the number of Multicast packets that were routed to the Satellite Interface. Could be Ethernet to Sat. or Sat. to Sat.
PAGE 194
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM Menu Options/Fields Entry Description Dropped – Filtered Read Only Limits certain types of traffic that should not leak to Satellite. For example, broadcasts destined for Satellite LAN Dropped – Multicast Disable Group Read Only Multicast packet was dropped because, although route existed, IGMP is being used, and there is no client requesting forwarding of this traffic.
PAGE 195
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.7.3 ADMINISTRATIVE DATABASE OPERATIONS PAGE The Administrative Database Operations Page is activated from the Operations and Maintenance Page. The Database Operations option allows the user to view, save, or erase an existing user configuration of the CiM. A CiM uses these types of configuration files to initialize itself on power-up.
PAGE 196
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.7.4 DIAGNOSTICS PAGE The Diagnostics Page is activated from the Operations and Maintenance Page. The Diagnostics Page contains the following options/fields: Menu Options/Fields Entry Description Dump Packets transmitted to Satellite Interface T Toggles [Yes] and [No] Executing this menu option forces the CiM to dump a hexadecimal representation of each packet that it transmits over the Satellite Interface.
PAGE 197
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM Menu Options/Fields Entry Description Command Line Debug Prompt D Enter the password to access the debug command line. Note: This is reserved for Customer Service and engineering use. Save Parameters S This option allows a user to save the current configuration of the CiM to permanent storage. This configuration will be restored on each successive power cycle of the CiM.
PAGE 198
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.7.5 REMOTE PORT B CONFIGURATION PAGE The Remote Port B Configuration page is activated from the Operations and Maintenance page. The Remote Port B Configuration page contains the following options/fields: Menu Options/Fields Entry Description Device Address A Valid ranges are from 0 to 9999 Baud Rate B The baud rate defines the speed of the serial interface.
PAGE 199
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.IOM 11.2.8 TELNET - LOGOUT OPTION When connecting to the CiM through a telnet session, the menus present another option to logout of the telnet session. This logout option is in all the menus and when selected, logs the user out of the telnet session, returning control of the CLI to the serial interface.
PAGE 200
CiM-550 IP Enabled Satellite Modem CLI and Telnet Interface Rev. 2 CD/CIM550.
PAGE 201
Chapter 12. Web Server Pages Web Server Usage 175 Web Server Menu Tree 175 Web Server Pages 178 Administration 182 Configuration Summary 184 Monitoring and Reports 199 Maintenance 207 12.1 WEB SERVER USAGE The embedded Web Server application provides the user with an easy to use interface to configure and monitor all aspects of the CiM-550 modem. These web pages have been designed for optimal performance when using MicroSoft’s Internet Explorer 5.5 or higher. 12.
PAGE 202
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM Table 12-1.
PAGE 203
CiM-550 IP Enabled Satellite Modem Web Server Pages Level 1 MONITORING & REPORTS MAINTENANCE Rev. 2 CD/CIM550.
PAGE 204
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3 WEB SERVER PAGES The CiM web menu pages are show here in order of appearance in the menu. 12.3.1 HOME PAGE Welcome to the CiM-550 Web Interface. The following sections will give you a brief introduction to each web page available. See the CDM-550 manual, the CiM Usage manual or the CLI section for further detailed explanation of CiM communication options.
PAGE 205
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.2 LOGOFF Currently the CiM only allows one connection to the CLI or the Web Interface. Use this option to formally disconnect from the Web Interface. Upon disconnection, you will be required to close the Web Browser so as to delete the security cookie to the CiM.
PAGE 206
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.3 CONTACT INFORMATION This page provides basic contact information to reach ComTech EF Data Sales and Customer Service via phone or automated e-mail links.
PAGE 207
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.4 SUPPORT The CiM Support page allows you to send an email to a pre-specified location. The email will contain the modem’s serial number and configuration information, which is attached automatically. The CiM uses SMTP (simple mail transport protocol) to send email and will require the modem’s administrator to specify the SMTP server, domain name and destination name on the Administration Screen for SMTP to operate correctly.
PAGE 208
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.5 ADMINISTRATION The Adminstration Page provides access to all CiM-550 IP administration features. This includes System Account Information, Host Access Lists, Feature Enable/Disable, etc., as described in the following table: Table 12-2. Admin Fields Field Description Account Names & Passwords Enter a unique name that identifies each kind of user.
PAGE 209
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM Field Description Optional Features This area allows you to enable or disable certain capabilities of the CiM system. SNMP Use this area to setup SNMP connectivity and security.
PAGE 210
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6 CONFIGURATION SUMMARY This page provides a read only summary of the IP administration parameters.
PAGE 211
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.1 INTERFACE CONFIGURATION This page is used to configure both the Ethernet (LAN) and Satellite (WAN) interfaces. In addition, control of Baud Rate and Character Format for the both the ‘Remote Control B’ port and the ‘Console’ Port are provided on this page. Table 12-3.
PAGE 212
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM Field Description Satellite (WAN) IP Address and Mask The CiM modem has two network interfaces: the Ethernet interface and the Satellite interface. Each of these network interfaces must be assigned an IP Address.
PAGE 213
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM Field Description Remote Port B Interface Type Allows the user to specify which communication standard the physical interface will comply to: EIA-232 EIA-485-2W EIA-485-4W CLI Console Port Baud Rate Fixed at 38,4000 Baud CLI Console Port Character Format Fixed at 8-N-1.
PAGE 214
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.2 ROUTES CONFIGURATION Table 12-4. Routes Configuration Fields Field Description Name Enter the name of the route to add or delete. The route name is case sensative however leading and trailing white space is automatically removed. IP Address/Mask Enter the destination IP address and mask. The mask and the IP address must be valid.
PAGE 215
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.3 MULTICAST ROUTES CONFIGURATION Table 12-5. Multicast Routes Configuration Fields Field Description Name Enter a valid route name to add or delete. This field is case sensative, however leading and tailing white space is automatically removed. Multicast IP Address Enter a valid multicast route address. Multicast addresses have the Class A value of 224 (ie, 224.10.2.1). IP mask is set to 32 bits.
PAGE 216
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.4 ADDRESS RESOLUTION PROTOCOL (ARP) CACHE Table 12-6. ARP Table Fields Field Description IP Address Enter a valid ARP table IP address to add or delete. Link Layer Address Enter a valid Link Layer Address which may be a device MAC address or HDLC address. The field requires hexidecimal input. For IEEE48 addresses, enter the value in the format of “xx:xx:xx:xx:xx:xx”, for HDLC, enter the value in the format of “xxxx”.
PAGE 217
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.5 QOS (QUALITY OF SERVICE) CONFIGURATION Table 12-7. QoS Fields Field Description Name Enter a valid Route Table Name. This field is case sensitive. Minimum/Maximum Bandwidth Enter the desired minimum and maximum bandwidth settings for the selected route. Priority Enter the desired priority (1 or 2) settings for the selected route. NOTE: See Section 6.2.3.
PAGE 218
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.6 IGMP CONFIGURATION Table 12-8. IGMP Fields Field Description Recognize IGMP Queries Set to indicate whether to recognize IGMP queries to the CiM device. IGMP Version Set to indicate whether to send V1 or V2 IGMP reports. Report Interval Enter the report interval value for sending IGMP reports. Cisco Router Alert Set to indicate whether to send the Cisco Router Alert type packets when sending IGMP reports (V1 only).
PAGE 219
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.7 DES ENCRYPTION CONFIGURATION Table 12-9. DES Encryption Fields Field Description DES Status This global setting indicates whether DES is an available option for the CiM. Transmit Key 1 & 2 Enter a valid 16 byte hexidecimal key used for encrypting transmitted packets. The receive side CiM should have these same values set for its Receive encryption Keys.
PAGE 220
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.8 REDUNDANCY CONFIGURATION Note: This page is not configurable unless the modem is properly connected to a Comtech EF Data qualified Redundancy Switch. Refer to Section 11.2.6 CLI/Telnet Redundancy Configuration for CRS-100/CiM-550 cabling information. Table 12-10. Redudancy Configuration Fields Field Description Local Unit Management IP Address/Mask Read only field displays the CiM unit’s IP address and mask values.
PAGE 221
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.
PAGE 222
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.10 MODEM UTILITIES The modem’s time and date field may be changed on this display as well as the modem’s front panel display identification string (Circuit ID). Please be aware that the CiM is synchronized to the modem’s time and date fields. Also provided on this page is the capability to re-center the modem’s buffer as well as force a 1:1 redundancy.
PAGE 223
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.11 ODU CONFIGURATION Refer to associated ODU/LNA manual for setting options.
PAGE 224
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.6.12 ODU UTILITIES Refer to associated ODU manual for setting options.
PAGE 225
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.7 MONITORING AND REPORTS Table 12-11. Monitoring and Reports Fields Field Description HDLC Transmit/Receive The Latch and Clock settings report the current alarms and conditions of the CiM.
PAGE 226
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.7.1 IP TX STATISTICS This page displays the IP transmit statistics for each IP route. Note: Refer to Section 11.2.7.2.1 CLI/Telnet Satellite Transmit Statistics for additional information.
PAGE 227
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.7.2 IP ROUTING STATISTICS This page displays the receive IP Routing Statistics for the CiM. Note: Refer to Section 11.2.7.2.2 CLI/Telnet IP Routing Statistics for additional information.
PAGE 228
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.7.3 MODEM STATUS This page provides a read-only summary of various modem status parameters.
PAGE 229
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.7.4 MODEM LOGS Field Description Modem Events Log Any occurance of a CiM modem fault will will be time stamped and recorded as an event. Similarly, the time of the fault condition clearing is also logged as an event. The event log can store up to 100 events. The Modem Event log window will display 5 events. I will also display the number of Unread Events and allow the user to Clear the Events Log.
PAGE 230
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM Field Description Modem Statistics Log The user may scroll backwards or forwards through the entries in the statistics log, using the UP/DOWN arrow keys. Pressing ENTER or CLEAR will take the user back to the previous menu. The event log can store up to 250 events. The top line of the display indicates the log entry number, and the time and date of the entry.
PAGE 231
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM The Modem Statistics logging interval can be configured from the CiM-550 front Panel. The User must first set the REMCONT to LOCAL. Then select MONITOR/ STATS/ CONFIGURE.The user is prompted to enter the logging interval (the period of time over which the statistics will be measured), using the UP/DOWN arrow keys, then press ENTER. Setting this to a value of 00 disables the feature (no logging).
PAGE 232
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.7.5 ODU STATUS This page provides a read-only summary of various ODU status parameters.
PAGE 233
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.8 MAINTENANCE 12.3.8.1 UNIT INFORMATION This screen displays the modems uptime, in seconds, serial number and software revision.
PAGE 234
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.8.2 FLASH SAVE When changes are made to the CiM protocol system, the Flash Save option must be selected in order for these settings to be valid through a power cycle. Without using this option, settings will revert back to their previous states as indicated by the last time the flash was saved.
PAGE 235
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.IOM 12.3.8.3 RESET The last item on the left-hand menu is “Reset.” This options will force the internal CiM module to reboot. Notes: 1. The main modem will NOT reboot. 2. There is no verification of the reboot, other than the web-interface timing out due to the reboot time of the CiM modile.
PAGE 236
CiM-550 IP Enabled Satellite Modem Web Server Pages Rev. 2 CD/CIM550.
PAGE 237
Chapter 13. SNMP Interface SNMP Interface 211 MIB-II 211 Private MIB Implementations 227 CIM IP Controller Private MIB 227 CiM 550 Private MIB 247 CiM IP Controller MIB Tree: 262 CiM-550 MIB Tree 355 CiM-550 MIB 359 13.1 SNMP INTERFACE The Simple Network Management Protocol (SNMP) is an application-layer protocol designed to facilitate the exchange of management information between network devices. The CiM-550 SNMP agent supports both SNMPv1 and v2c. 13.
PAGE 238
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM Table 13-1. MIB-II Support Group Commets System Group Mandatory for RFC1213 Interface Mandatory for RFC1213 IP Mandatory for RFC1213 ICMP Mandatory for RFC1213 TCP Mandatory for RFC1213 UDP Mandatory for RFC1213 SNMP Mandatory for RFC1213 Address Translation Group Implemented but depreciated in MIB-II EGP Not applicable 13.2.1 SYSTEM GROUP This System Group provides information about the following items: Table 13-2.
PAGE 239
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM The system services provided by the cim550 in the OSI network model are: ∑2L-1 where L is the network layer support by the cim550. In the cim550, this is calculated by 21-1 (layer 1) + 22-1 (layer 2) + 23-1 (layer 3) + 24-1 (layer 4) + 27-1 (layer 7) = 1 + 2 + 4 + 8 + 64 = 79. Table 13-3.
PAGE 240
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.2.2 INTERFACE GROUP This group provides the number of interfaces on a managed device and a table describing all interfaces. The ifNumber OID is the number of network interfaces present on this system. On a cim550 the ifNumber should be 3 corresponding to the Ethernet, Satellite, and Loopback interfaces. 13.2.2.1 THE INTERFACES TABLE Table 13-4. Interfaces Table OIDs OID Description ifIndex Unique value for each interface.
PAGE 241
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description ifInUcastPkts Number of subnetwork-unicast packets received on the interface. This statistic is counted for both the Ethernet and Satellite interfaces. ifInNUcastPkts Number of non-unicast (i.e. broadcast or multicast) packets received on the interface. This statistic is counted for both the Ethernet and Satellite interfaces.
PAGE 242
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.2.2.2 AT GROUP This group contains a table that permits mappings from network addresses (i.e. IP addresses) to physical addresses (i.e. MAC addresses). This group is depreciated. 13.2.2.3 THE ADDRESS TRANSLATION TABLE Table 13-5. Address Translation Table OIDs OID Description atIfIndex Interface on which this entry's translation is effective. atPhysAddress Media-dependent physical address. atNetAddress Network address (i.e.
PAGE 243
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description ipForwDatagrams Number of input datagrams for which the cim550 was not their final IP destination, because of which an attempt was made to find a route to forward them to that final destination. ipInUnknownProtos Number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.
PAGE 244
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.2.2.5 THE IP ADDRESS TABLE The IP address table contains the cim550’s IP addressing information. Table 13-7. IPAddress Table OIDs OID Description ipAdEntIfIndex CIM-550’s Interface index value (ifIndex) which uniquely identifies the interface to which the IP address is applicable. ipAdEntNetMask Subnet mask associated with the IP address of this entry.
PAGE 245
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.2.2.6 THE IP ROUTING TABLE The IP routing table contains an entry for each route presently known to the cim550. Table 13-8. IP Routing Table OIDs OID Description ipRouteDest Destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. ipRouteIfIndex Index value (ifIndex) which uniquely identifies the local interface through which the next hop of this route should be reached.
PAGE 246
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.2.2.7 THE ADDRESS TRANSLATION TABLE The ipNetToMediaTable is the IP Address Translation table used for mapping from IP addresses to physical addresses. Each entry contains one IP address to physical address equivalence. Table 13-9. Address Translation Table OIDs OID Description ipNetToMediaIfIndex Interface on which this entry's equivalence is effective. ipNetToMediaPhysAddress Physical address.
PAGE 247
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.2.3 ICMP GROUP This group contains the Internet Control Message Protocol (ICMP) input and output statistics. ICMP messages are used for out-of-band messages related to network operation. Table 13-10. IP Routing Table OIDs OID Description icmpInMsgs Total number of ICMP messages which the entity received.
PAGE 248
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.2.4 TCP GROUP This group contains statistics and control parameters for the TCP protocol. This group contains a table describing the current TCP connections. Note: The instances of object types that represent information about a particular TCP connection are transient; they persist only as long as the connection in question. Table 13-11.
PAGE 249
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.2.4.1 THE TCP CONNECTION TABLE The tcpConnTable is a table containing TCP connection-specific information. Each row contains information about a particular current TCP connection. A row is transient, in that it ceases to exist when the connection makes the transition to the CLOSED state. Table 13-12. TCP Connection Table OIDs OID Description tcpConnLocalAddress Local IP address for this TCP connection.
PAGE 250
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.2.5.1 THE UDP LISTENER TABLE The UDP listener table contains information about this entity's UDP end-points on which a local application is currently accepting datagrams. A row contains information about a particular current UDP listener. Table 13-14. UDP Listener Table OIDs OID Description udpLocalAddress Local IP address for this UDP listener.
PAGE 251
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.2.6 EGP GROUP This group is not implemented in the agent. 13.2.7 TRANSMISSION GROUP This group is not implemented in the agent. 13.2.8 SNMP GROUP This group provides statistical information regarding the SNMP Protocol. Table 13-15. SNMP Group OIDs OID Description snmpInPkts Total number of Messages delivered to the SNMP entity from the transport service.
PAGE 252
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description snmpInTotalSetVars Total number of MIB objects which have been altered successfully by the SNMP agent as the result of receiving valid SNMP Set-Request PDUs. snmpInGetRequests Total number of SNMP Get-Request PDUs which have been accepted and processed by the SNMP agent. snmpInGetNexts Total number of SNMP Get-Next PDUs which have been accepted and processed by the SNMP agent.
PAGE 253
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.3 PRIVATE MIB IMPLEMENTATIONS The agent also implements two private MIBs for the CiM-550. The CiM IP Controller MIB (cimController) holds all the security, feature selection, and IP related parameters and the CiM-550 modem MIB (cim550) which contains all the modem specific parameters. 13.4 CIM IP CONTROLLER PRIVATE MIB 13.4.
PAGE 254
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.1.2 CIM ACCESS LISTS SUBGROUP The Access Client List allows an operator to define which remote clients can connect to a CiM-550 when the Access List Enforcement is enabled. Each entry allows an operator to specify an IP address and a subnet mask to define a unique class of clients that are allowed access to the CiM-550. Table 13-17. CiM Access Lists Subgroup OIDs OID Description cimAccessIpAddress1 Defines an access IP address.
PAGE 255
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.1.3 FEATURES AVAILABILITY SUBGROUP This subgroup tells if a feature is available or unavailable in the CiM-550. The currently supported FAST features are QOS, IGMP, and Encryption. These features must be purchased as additional options. The Datagram Compression, NAPT, TCP Acceleration, Transparent Bridging, and Header Compression features are not yet supported but will be made available in a follow on release. Table 13-18.
PAGE 256
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.1.4 FEATURES SUBGROUP This subgroup allows an operator to enable/disable a feature. Standard features that are supported (telnet, ping response, and multicast routing) can be enabled or disabled by sending a 1 (enable) or 0 (disable). The Midas Operations Feature is always enabled and cannot be disabled.
PAGE 257
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.1.5 ENCRYPTION SUBGROUP Note: This subgroup will only be accessible in the MIB tree if the Encryption FAST feature has been purchased and the license key has been entered through the modem’s front panel. Otherwise, both GETS and SETS on these OIDs will return errors. This subgroup controls the parameters for the DES feature. Table 13-20.
PAGE 258
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.1.7 CIM SNMP COMMUNITY NAMES The CiM-550 uses community strings as a password scheme that provides authentication before gaining access to the CiM-550 agent’s MIBs. In SNMP v1/v2c, the community string is sent unencrypted in the SNMP packets. Caution must be taken by the network administrator to ensure that SNMP packets travel only over a secure and private network if security is a concern.
PAGE 259
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.1.8 CIM SNMP TRAPS The cim550 has the ability to send out SNMP traps when certain events occur in the modem. For example, when the cim550 boots it sends out a coldstart trap and 3 linkup traps, one for each interface that is brought up. The cim550 also sends out traps when an alarm or a fault occurs in the modem. These include unit faults, TX faults, and RX faults. A trap is sent both when a fault occurs and is cleared.
PAGE 260
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM CiM550 Alarms and Faults SNMPv2 notifications: cim550ModemUnitFaultsTrap 1.3.6.1.4.1.6247.5.1.9.0.624751 cim550ModemTxTrafficFaultsTrap 1.3.6.1.4.1.6247.5.1.9.0.624752 cim550ModemRxTrafficFaultsTrap 1.3.6.1.4.1.6247.5.1.9.0.624753 13.4.1.9 CIM SNMP TRAP CONFIGURATION Table 13-23. CIM SNMP Trap COnfiguration OIDs OID Description cimSnmpTrapDestinationIpAddress Specifies where the trap should be sent to.
PAGE 261
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.2 INTERFACE GROUP This Group controls the parameters of the modem’s Ethernet and HDLC interfaces. 13.4.2.1 ETHERNET INTERFACE SUBGROUP The subgroup defines the modem’s Ethernet interface. These include parameters for setting the Ethernet speed, IP address, and IP address subnet prefix length. Table 13-24. Ethernet Interface Subgroup OIDs OID Description cimEthernetMacAddress Defines the hardware MAC Address.
PAGE 262
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.2.2 SATELLITE INTERFACE SUBGROUP This subgroup defines the modem’s Satellite interface. Table 13-25. Satellite Ijnterface Subgroup OIDs OID Description cimSatelliteIpAddress Specifies the IP Address assigned to the Satellite Interface.
PAGE 263
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.2.3 ROUTE TABLE GROUP Note: In order for the CiM-550 to properly pass packets over the satellite interface, the user MUST provide the appropriate IP to HDLC address mapping in the ARP table. Please see the ARP Configuration Group for more details. Table 13-26. Route Table Group OIDs OID Description cimGlobalQosEnable Allows an operator to vie the status of the QOS feature (enabled/disabled).
PAGE 264
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description cimIpRouteMaxQosBandwidth Establishes a hard maximum traffic rate that can be processed by the CiM-550. A value of 0 for this field implies that no maximum limit is assigned to a route. This value should be in multiples of 8 Kbps. Note: The “cimIpRouteDesKey” OID will only be accessible if the Encryption FAST feature has been purchased and activated.
PAGE 265
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.2.4 PROTOCOLS GROUP 13.4.2.4.1 IGMP Configuration Subgroup Note: This subgroup will only be accessible in the MIB tree if the IGMP FAST feature has been purchased and activated. Otherwise, both gets and sets on these OIDs will return errors. Table 13-28. IGMP Configuration Subgroup OIDs OID Description cimIgmpTable Reports the host groups being routed by the modem.
PAGE 266
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.2.4.2 ARP Configuration Subgroup Table 13-29. ARP Configuration Subgroup OIDs OID Description cimFlushArpTable Can be used to flush the non-static ARP table. The cimArpTable is used to configure the static ARP table. This table allows up to 256 static ARP entries. The Static ARP entries provided by the CiM-550 fall into two categories: IP-to-MAC and IP-to-HDLC.
PAGE 267
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description cimArpRowStatus Used for to create or delete an ARP entry. This OID returns 1 (active) to indicate that an ARP entry is available for use by the managed device. The values of 2 (notInService) and 3 (notReady) are not supported. When creating a new ARP entry this OID must be set to 4 (createAndGo). The value of 5 (createAndWait) is not supported.
PAGE 268
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.2.5 REDUNDANCY GROUP Table 13-31. Redundancy OIDs OID Description cimCurrentRedundantState Displays if the modem is Online and Offline. The Online modem is the one that will process traffic. The Offline modem monitors the health of the online unit and will take over if it detects a failure. cimLocalUnitManagementIpAddress IP Address for the Ethernet Interface for the Local Unit.
PAGE 269
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.2.6.1 Remote Port B Configuration Subgroup This subgroup defines the Remote Port B configuration. Table 13-33. Remote Port B Configuration Subgroup OIDs OID Description cimRemotePortBDeviceAddress Defines the device address. Valid addresses are in the range from 0 to 9999. cimRemotePortBBaudRate Defines the speed of the serial interface.
PAGE 270
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.2.6.2 Satellite Transmit Statistics Subgroup This subgroup contains a table to show the number of packets transmitted on each route destined for the satellite interface. It also contains the number of packets dropped and the route’s data rate. Table 13-34. Satellite Transmit Statistics Subgroup OIDs OID Description cimSatelliteTransmitIndex This is a sequence number defining the row in the Satellite Transmit Statistics table.
PAGE 271
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.4.2.6.3 IP Routing Statistics Subgroup Table 13-35. IP Routing Statistics Subgroup OIDs OID Description cimUnicastIpPacketsToSatellite Number of unicast packets that were routed to the Satellite Interface. (Ethernet to Satellite or Satellite to Satellite) cimUnicastIpPacketsToEthernet Number of unicast packets that were routed to the Ethernet Interface. (Satellite to Ethernet or Ethernet to Ethernet).
PAGE 272
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description cimDroppedPacketsNoRoute Number of packets that were dropped because their destination address did not match any of the configured routes in the CiM-550 Route table. cimDroppedPacketsMulticastNoStoe Number of multicast packets that where filtered because of the configurable filtering option. cimDroppedPacketsFiltered Number of packets that were dropped because they matched a “filter” route.
PAGE 273
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.5 CIM 550 PRIVATE MIB 13.5.1 CIM 550 OBJECTS GROUP 13.5.1.1 SYSTEM INFORMATION: Table 13-36. ARP Configuration Subgroup OIDs OID Description cim550EquipmentID Unit’s equipment ID. cim550UnitSerialNumber Unit’s serial number. cim550SoftwareRevision Unit’s softeare revision. cim550DeviceTime Device time. Current time is in hh:mm:ss format. cim550DeviceDate Device date. Current date is in mm/dd/yy format.
PAGE 274
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description cim550TxFECType Transmit forward error correction coding type. Valid values are: cim550TxFECCodeRate cim550TxSpecInv cim550TxScrambler cim550TxClockSource 0 None 1 Vit 2 Seq 3 Vit RS 4 Seq RS 5 Turbo Q 3/4 6 Turbo B 21/44 7 Turbo B 5/16 Transmit forward error correction code rate.
PAGE 275
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.5.1.3 RX PARAMETERS Table 13-38. Rx Parameters OIDs OID Description cim550RxFrequency Receive frequency in Hz. Can be set from 52,000,000 Hz to 88,000,000 Hz and 104,000,000 Hz to 188,000,000 Hz. cim550RxDataRate Receive data rate in bps. Can be set between 2,400 bps and 2,048,000 bps. cim550RxDemodType Receive demodulation type.
PAGE 276
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description cim550RxClockMode Receive clock mode. Can be set to: cim550RxBufferSize 0 Disabled 1 Enabled Receive buffer size in bits. Can be set to: 1 256 bits 2 512 bits 3 1024 bits 4 2048 bits 5 4096 bits cim550RxAcqSweepRange Receive +/- acquisition sweep range of deomulation in KHz. Can be set between 1 and 30. cim550RxEbnoAlarmPoint Receive Eb/No alarm point in dB. Can be set between 0 and 160 in 0.
PAGE 277
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description cim550EdmacAddress The EDMAC slave address will set the range of addresses of distant-end units (modems and transceivers) which this unit will forward messages for. Only values that are integer multiples of ten are permitted. Setting the EDMAC slave address to 0 disables this function. Valid slave addresses are between 0 and 9999. cim550UnitTestMode Unit test mode.
PAGE 278
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.5.1.6 THE “”AUPC PARAMETERS Table 13-41. AUPC Parameter OIDs OID Description cim550AupcEnable Enables or disables AUPC (Automatic Uplink Power Control). Can be set to: 0 Disable 1 Enable cim550AupcControlParameters Defines AUPC (Automatic Uplink Power Control) operating parameters. Has the form abc.
PAGE 279
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.5.1.7 STATUS PARAMETERS Table 13-42. Status Parameter OIDs OID Description cim550RxEbno Value of Ebi/No, can be between 0 and 160 in 0.1 dB where 0 = 0.0 dB to 160 = 16.0 dB and 999 = Demod Unlocked cim550RxCoarseAGC Vaue of Coarse AGC setting, can be between 0 and 99. cim550RxFrequencyOffset Value of frequency offset of the carrier being demodulated.
PAGE 280
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description cim550ModemTxTrafficFaults Returns the current fault and status codes for the Tx Traffic.
PAGE 281
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.5.1.8 LOGS Table 13-43. Logs OIDs OID Description cim550ClearEventsLog Instructs the unit to clear all Stored Events. A value of 1 (yes) is used to clear the event log. cim550NumberUnreadEvents Returns the number of Stored Events which remain unread. The value can be between 0 and 99. cim550RetrieveNext5Events Unit returns the oldest 5 Stored Events which have not yet been read over the remote control.
PAGE 282
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description cim550RetrieveNext5Statistics Unit returns the oldest 5 Stored Statistics which have not yet been read over the remote control. Reply format: {CR}Sub-body{CR}Sub-body{CR}Subbody{CR}Subbody{CR}Sub-body, where Sub-body= AA.ABB.BC.CD.Dddmmyyhhmmss, AA.A = Minimum Eb/No during sample period. BB.B = Average Eb/No during sample period. C.C = Max. Tx Power Level Increase during sample period. D.
PAGE 283
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.5.1.11 ODU UNIT PARAMETERS Table 13-45. ODU Unit OIDs OID Description oduUnitMuteMode Unit mute. Can be set to: oduUnitColdStart oduUnitAutoFaultRecovery oduUnitExtRefFaultLogic 0 Unmute 1 Mute Unit cold start. Can be set to: 0 Disabled 1 Enabled Auto fault recovery. Can be set to: 0 Disabled 1 Enabled External reference fault logic.
PAGE 284
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.5.1.12 ODU TX PARAMETERS Table 13-46. ODU Tx Parameters OIDs OID Description OduTxFrequency Transmit frequency in KHz. Can be set between 5,845,000 KHz and 181,00,000 KHz. OduTxAttenuation Transmit attenuation. Can be between 0 and 2000 in 0.01 dB, where 0 = 0.00dB to 2000 = 20.00dB. OduTxAmplifier Transmit amplifier. Can be set to: OduTxMute OduTxSlopeMode 0 Off 1 On Transmit mute.
PAGE 285
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.5.1.13 ODU RX PARAMETERS Table 13-47. ODU Rx Parameters OIDs OID Description OduRxFequency Receive frequency in KHz. Can be between 3,625,000 KHz and 14,100,000 KHz. oduRxAttenuation Receive attenuation. Can be between 0..2500 in 0.01dB where 0=0.00dB to 2500=25.00dB. oduRxMute Receive mute. Can be set to: oduRxSlopeMode 0 Disabled 1 Enabled Receive slope mode.
PAGE 286
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.5.1.14 ODU UNIT STATUS Table 13-48. ODU Unit Status OIDs OID Description OduOnlineState Online state. Can be set to: oduMaintenanceParameters 0 Offline 1 Online Used to Query the maintenance status of the CSAT. Example: 24VT=023.9’cr’ 20VT=020.3’cr’ 12VT=012.0’cr’ 10VT=010.2’cr’ P5VT=005.0’cr’ N5VT=-05.0’cr’ USYN=008.2’cr’ UIFL=003.9’cr’ DSYN=006.3’cr’ DIFL=003.8’cr’ REFV=002.9’cr’ LNAC=081.9’cr’ FANC=541.0’cr’ UTMP= 37.
PAGE 287
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM OID Description OduUnitFaults Used to Query the Alarm status of the CSAT. A integer value will be returned between 0..
PAGE 288
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.6 CIM IP CONTROLLER MIB TREE: MIB Tree: 1 --- iso 1.3 --- org 1.3.6 --- dod 1.3.6.1 --- internet 1.3.6.1.4 --- private 1.3.6.1.4.1 --- enterprises 1.3.6.1.4.1.6247 --- comtech 1.3.6.1.4.1.6247.4 --- cimController 1.3.6.1.4.1.6247.4.1 --- cimControllerIdentity 1.3.6.1.4.1.6247.4.2 --- cimAdministration 1.3.6.1.4.1.6247.4.2.1 --- cimMibVersion (INTEGER) 1.3.6.1.4.1.6247.4.2.3 --- cimNamePasswordConfig 1.3.6.1.4.1.6247.4.2.3.
PAGE 289
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 1.3.6.1.4.1.6247.4.2.5.1 --- cimDatagramCompressionOption (Availability) 1.3.6.1.4.1.6247.4.2.5.2 --- cimNaptOption (Availability) 1.3.6.1.4.1.6247.4.2.5.3 --- cimQosOption (Availability) 1.3.6.1.4.1.6247.4.2.5.4 --- cimTcpAccelerationOption (Availability) 1.3.6.1.4.1.6247.4.2.5.5 --- cimTransparentBridgeOption (Availability) 1.3.6.1.4.1.6247.4.2.5.6 --- cimEncryptionOption (Availability) 1.3.6.1.4.1.6247.4.2.5.
PAGE 290
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 1.3.6.1.4.1.6247.4.2.8.3 --- cimSmtpDestinationName(DisplayString) 1.3.6.1.4.1.6247.4.2.9 --- cimSnmp 1.3.6.1.4.1.6247.4.2.9.1 --- cimSnmpTrapDestinationIpAddress (IpAddress) 1.3.6.1.4.1.6247.4.2.9.2 --- cimSnmpTrapCommunity (DisplayString) 1.3.6.1.4.1.6247.4.2.9.3 --- cimSnmpTrapVersion (INTEGER) 1.3.6.1.4.1.6247.4.2.9.4 --- cimSnmpAuthenticationFailureCommunity (DisplayString) 1.3.6.1.4.1.6247.4.2.9.
PAGE 291
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 1.3.6.1.4.1.6247.4.4.3.1.6 --- cimIpRouteMulticastOptions (INTEGER) 1.3.6.1.4.1.6247.4.4.3.1.7 --- cimIpRouteMinQosBandwidth (INTEGER) 1.3.6.1.4.1.6247.4.4.3.1.8 --- cimIpRouteMaxQosBandwidth (INTEGER) 1.3.6.1.4.1.6247.4.4.3.1.9 --- cimIpRouteDesKey (INTEGER) 1.3.6.1.4.1.6247.4.4.3.1.10 --- cimIpRouteRowStatus (INTEGER) 1.3.6.1.4.1.6247.4.4.3.1.11 --- cimIpRoutePriority (INTEGER32) 1.3.6.1.4.1.6247.4.5 --- cimProtocols 1.3.6.1.4.1.
PAGE 292
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 1.3.6.1.4.1.6247.4.5.2.2.1.4 --- cimArpPhysType (INTEGER) 1.3.6.1.4.1.6247.4.5.2.2.1.5 --- cimArpRowStatus (INTEGER) 1.3.6.1.4.1.6247.4.6 --- cimRedundancy 1.3.6.1.4.1.6247.4.6.1 --- cimCurrentRedundantState (INTEGER) 1.3.6.1.4.1.6247.4.6.2 --- cimLocalUnitManagementIpAddress (IpAddress) 1.3.6.1.4.1.6247.4.6.3 --- cimRedundantUnitManagementIpAddress (IpAddress) 1.3.6.1.4.1.6247.4.6.4 --- cimRedundantTrafficIpAddress (IpAddress) 1.3.6.
PAGE 293
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 1.3.6.1.4.1.6247.4.8.2 --- cimIpRoutingStatistics 1.3.6.1.4.1.6247.4.8.2.1 --- cimUnicastIpPacketsToSatellite (Counter32) 1.3.6.1.4.1.6247.4.8.2.2 --- cimUnicastIpPacketsToEthernet (Counter32) 1.3.6.1.4.1.6247.4.8.2.3 --- cimMulticastIpPacketsToSatellite (Counter32) 1.3.6.1.4.1.6247.4.8.2.4 --- cimMulticastIpPacketsToEthernet (Counter32) 1.3.6.1.4.1.6247.4.8.2.5 --- cimBroadcastIpPacketsToSatellite (Counter32) 1.3.6.1.4.1.6247.4.8.2.
PAGE 294
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7 CIM IP CONTROLLER MIB 13.7.1 CIMCONTROLLER Name OID Full path Module Parent Child Type Organization Last updated Contact info Description cimController 1.3.6.1.4.1.6247.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4) CIMController comtech cimControllerIdentity MODULE-IDENTITY Comtech EF Data 200204180800Z 2114 West 7th Street Tempe, AZ 85281 USA CIM IP Controller 13.7.
PAGE 295
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.4 CIMMIBVERSION Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimMibVersion 1.3.6.1.4.1.6247.4.2.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).
PAGE 296
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.6 CIMADMINNAME Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimAdminName 1.3.6.1.4.1.6247.4.2.3.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimNamePasswordConf ig(3).
PAGE 297
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.8 CIMREADWRITENAME Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimReadWriteName 1.3.6.1.4.1.6247.4.2.3.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimNamePasswordConf ig(3).
PAGE 298
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.10 CIMREADONLYNAME Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimReadOnlyName 1.3.6.1.4.1.6247.4.2.3.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimNamePasswordConf ig(3).
PAGE 299
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.12 CIMACCESSLISTS Name OID Full path Module Parent Prev sibling Next sibling Child Type cimAccessLists 1.3.6.1.4.1.6247.4.2.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimAccessLists(4) CIMController cimAdministration cimNamePasswordConfig cimFeaturesAvailability cimAccessIpAddress1 OBJECT-IDENTIFIER 13.7.
PAGE 300
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.14 CIMACCESSSUBNETMASKLEN1 Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimAccessSubnetMaskLen1 1.3.6.1.4.1.6247.4.2.4.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimAccessLists(4).
PAGE 301
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.16 CIMACCESSSUBNETMASKLEN2 Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimAccessSubnetMaskLen2 1.3.6.1.4.1.6247.4.2.4.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimAccessLists(4).
PAGE 302
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.18 CIMACCESSSUBNETMASKLEN3 Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimAccessSubnetMaskLen3 1.3.6.1.4.1.6247.4.2.4.6 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimAccessLists(4).
PAGE 303
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.20 CIMACCESSSUBNETMASK4 Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimAccessSubnetMask4 1.3.6.1.4.1.6247.4.2.4.8 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimAccessLists(4).
PAGE 304
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.22 CIMFEATURESAVAILABILITY Name OID Full path Module Parent Prev sibling Next sibling Child Type cimFeaturesAvailability 1.3.6.1.4.1.6247.4.2.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimFeaturesAvailability( 5) CIMController cimAdministration cimAccessLists cimFeaturesConfig cimDatagramCompressionOption OBJECT-IDENTIFIER 13.7.
PAGE 305
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.24 CIMNAPTOPTION Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimNaptOption 1.3.6.1.4.1.6247.4.2.5.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimFeaturesAvailability( 5).
PAGE 306
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.26 CIMTCPACCELERATIONOPTION Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimTcpAccelerationOption 1.3.6.1.4.1.6247.4.2.5.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimFeaturesAvailability( 5).
PAGE 307
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.28 CIMENCRYPTIONOPTION Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimEncryptionOption 1.3.6.1.4.1.6247.4.2.5.6 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimFeaturesAvailability( 5).
PAGE 308
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.30 CIMHEADERCOMPRESSIONOPTION Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimHeaderCompressionOption 1.3.6.1.4.1.6247.4.2.5.8 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimFeaturesAvailability( 5).
PAGE 309
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.33 CIMTELNETFEATURE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimTelnetFeature 1.3.6.1.4.1.6247.4.2.6.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimFeaturesConfig(6).
PAGE 310
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.35 CIMDOWNLINKMULTICASTROUTINGFEATURE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimDownlinkMulticastRoutingFeature 1.3.6.1.4.1.6247.4.2.6.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimFeaturesConfig(6).
PAGE 311
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.37 CIMNAPTOPT Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimNaptOpt 1.3.6.1.4.1.6247.4.2.6.6 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimFeaturesConfig(6).
PAGE 312
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.39 CIMTCPACCELERATIONOPT Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimTcpAccelerationOpt 1.3.6.1.4.1.6247.4.2.6.8 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimFeaturesConfig(6).
PAGE 313
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.41 CIMTRANSMITDESENCRYPTIONOPT Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimTransmitDesEncryptionOpt 1.3.6.1.4.1.6247.4.2.6.10 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimFeaturesConfig(6).
PAGE 314
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.43 CIMIGMPOPT Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimIgmpOpt 1.3.6.1.4.1.6247.4.2.6.12 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimFeaturesConfig(6).
PAGE 315
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.45 CIMDESENCRYPTCONFIG Name OID Full path Module Parent Prev sibling Next sibling Child Type cimDesEncryptConfig 1.3.6.1.4.1.6247.4.2.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimDesEncryptConfig(7 ) CIMController cimAdministration cimFeaturesConfig cimSmtp cimTransmitEncryptEnabled OBJECT-IDENTIFIER 13.7.
PAGE 316
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.47 CIMRECEIVEDECRYPTENABLED Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimReceiveDecryptEnabled 1.3.6.1.4.1.6247.4.2.7.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimDesEncryptConfig(7 ).
PAGE 317
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.49 CIMTRANSMITKEY2 Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimTransmitKey2 1.3.6.1.4.1.6247.4.2.7.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimDesEncryptConfig(7 ).
PAGE 318
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.51 CIMRECEIVEKEY2 Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimReceiveKey2 1.3.6.1.4.1.6247.4.2.7.6 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimDesEncryptConfig(7 ).
PAGE 319
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.53 CIMSMTPSERVERIPADDRESS Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimSmtpServerIpAddress 1.3.6.1.4.1.6247.4.2.8.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimSmtp(8).
PAGE 320
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.55 CIMSMTPDESTINATIONNAME Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimSmtpDestination 1.3.6.1.4.1.6247.4.2.8.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimSmtp(8).
PAGE 321
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.57 CIMSNMPTRAPDESTINATIONIPADDRESS Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimSnmpTrapDestinationIpAddress 1.3.6.1.4.1.6247.4.2.9.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimSnmp(9).
PAGE 322
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.59 CIMSNMPTRAPVERSION Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description cimSnmpTrapVersion 1.3.6.1.4.1.6247.4.2.9.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimSnmp(9).
PAGE 323
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.61 CIMSNMPAUTHENTICATIONFAILUREADDRESS Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Description cimSnmpAuthenticationFailureAddress 1.3.6.1.4.1.6247.4.2.9.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimAdministration(2).cimSnmp(9).
PAGE 324
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.64 CIMETHERNETMACADDRESS Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimEthernetMacAddress 1.3.6.1.4.1.6247.4.3.1.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimInterfaces(3).cimEthernetInterface(1).
PAGE 325
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.66 CIMETHERNETIPADDRESS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimEthernetIpAddress 1.3.6.1.4.1.6247.4.3.1.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimInterfaces(3).cimEthernetInterface(1).
PAGE 326
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.68 CIMSATELLITEINTERFACE Name OID Full path Module Parent Prev sibling Child Type cimSatelliteInterface 1.3.6.1.4.1.6247.4.3.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimInterfaces(3).cimSatelliteInterface(2) CIMController cimInterfaces cimEthernetInterface cimSatelliteIpAddress OBJECT-IDENTIFIER 13.7.
PAGE 327
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.70 CIMSATELLITESUBNETPREFIXLEN Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimSatelliteSubnetPrefixLen 1.3.6.1.4.1.6247.4.3.2.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimInterfaces(3).cimSatelliteInterface(2).
PAGE 328
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.72 CIMSATELLITETRANSMITENABLE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimSatelliteTransmitEnable 1.3.6.1.4.1.6247.4.3.2.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimInterfaces(3).cimSatelliteInterface(2).
PAGE 329
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.74 CIMSATELLITEHDLCADDRESS2 Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 2 Description cimSatelliteHdlcAddress2 1.3.6.1.4.1.6247.4.3.2.6 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimInterfaces(3).cimSatelliteInterface(2).
PAGE 330
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.76 CIMSATELLITEHDLCADDRESS4 Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 2 Description cimSatelliteHdlcAddress4 1.3.6.1.4.1.6247.4.3.2.8 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimInterfaces(3).cimSatelliteInterface(2).
PAGE 331
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.78 CIMGLOBALQOSENABLE Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimGlobalQosEnable 1.3.6.1.4.1.6247.4.4.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRouteTable(4).
PAGE 332
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.80 CIMIPROUTEENTRY Name OID Full path Module Parent Child Type Numerical syntax Base syntax Composed syntax Status Max-access Sequences 1 2 3 4 5 6 7 8 9 10 Indexes 1 Description cimIpRouteEntry 1.3.6.1.4.1.6247.4.4.3.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRouteTable(4).cimIpRouteTable(3).
PAGE 333
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.81 CIMIPROUTEINDEX Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimIpRouteIndex 1.3.6.1.4.1.6247.4.4.3.1.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRouteTable(4).cimIpRouteTable(3).cimIp RouteEntry(1).
PAGE 334
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.83 CIMIPROUTEDESTADDRESS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimIpRouteDestAddress 1.3.6.1.4.1.6247.4.4.3.1.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRouteTable(4).cimIpRouteTable(3).cimIp RouteEntry(1).
PAGE 335
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.85 CIMIPROUTENEXTHOPADDRESS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimIpRouteNextHopAddress 1.3.6.1.4.1.6247.4.4.3.1.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRouteTable(4).cimIpRouteTable(3).cimIp RouteEntry(1).
PAGE 336
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.87 CIMIPROUTEMINQOSBANDWIDTH Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Default values 1 Description cimIpRouteMinQosBandwidth 1.3.6.1.4.1.6247.4.4.3.1.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRouteTable(4).cimIpRouteTable(3).cimIp RouteEntry(1).
PAGE 337
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.89 CIMIPROUTEDESKEY Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 3 4 Default values 1 Description cimIpRouteDesKey 1.3.6.1.4.1.6247.4.4.3.1.9 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRouteTable(4).cimIpRouteTable(3).cimIp RouteEntry(1).
PAGE 338
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.90 CIMIPROUTEROWSTATUS Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 3 4 5 6 Description cimIpRouteRowStatus 1.3.6.1.4.1.6247.4.4.3.1.10 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRouteTable(4).cimIpRouteTable(3).cimIp RouteEntry(1).
PAGE 339
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.91 CIMIPROUTEPRIORITY Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimIpRoutePriority 1.3.6.1.4.1.6247.4.4.3.1.11 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(62 47).cimController(4).cimRouteTable(4).cimIpRouteTable(3).cimIpRo uteEntry(1).
PAGE 340
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.94 CIMIGMPTABLE Name OID Full path Module Parent Next sibling Child Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimIgmpTable 1.3.6.1.4.1.6247.4.5.1.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimIgmpConfig(1).
PAGE 341
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.96 CIMIGMPINDEX Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimIgmpIndex 1.3.6.1.4.1.6247.4.5.1.1.1.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimIgmpConfig(1).cimIgmpT able(1).cimIgmpEntry(1).
PAGE 342
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.98 CIMIGMPCLIENTSTATE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 3 Description cimIgmpClientState 1.3.6.1.4.1.6247.4.5.1.1.1.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimIgmpConfig(1).cimIgmpT able(1).cimIgmpEntry(1).
PAGE 343
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.100 CIMIGMPGROUPIPADDRESS Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimIgmpGroupIpAddress 1.3.6.1.4.1.6247.4.5.1.1.1.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimIgmpConfig(1).cimIgmpT able(1).cimIgmpEntry(1).
PAGE 344
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.102 CIMIGMPENABLE Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimIgmpEnable 1.3.6.1.4.1.6247.4.5.1.2.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimIgmpConfig(1).cimIgmpR eceiver(2).
PAGE 345
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.104 CIMIGMPMAXRESPTIME Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimIgmpMaxRespTime 1.3.6.1.4.1.6247.4.5.1.2.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimIgmpConfig(1).cimIgmpR eceiver(2).
PAGE 346
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.106 CIMIGMPTRANSMITER Name OID Full path Module Parent Prev sibling Child Type cimIgmpTransmiter 1.3.6.1.4.1.6247.4.5.1.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimIgmpConfig(1).cimIgmpTr ansmiter(3) CIMController cimIgmpConfig cimIgmpReceiver cimIgmpRecognizeQueries OBJECT-IDENTIFIER 13.7.
PAGE 347
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.108 CIMIGMPVERSIONUNSOLICITEDREPORTS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description cimIgmpVersionUnsolicitedReports 1.3.6.1.4.1.6247.4.5.1.3.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimIgmpConfig(1).cimIgmpTr ansmiter(3).
PAGE 348
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.110 CIMIGMPUNSOLICITEDREPORTINTERVAL Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimIgmpUnsolicitedReportInterval 1.3.6.1.4.1.6247.4.5.1.3.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimIgmpConfig(1).cimIgmpTr ansmiter(3).
PAGE 349
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.112 CIMFLUSHARPTABLE Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimFlushArpTable 1.3.6.1.4.1.6247.4.5.2.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimArpConfig(2).
PAGE 350
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.114 CIMARPENTRY Name OID Full path Module Parent Child Type Numerical syntax Base syntax Composed syntax Status Max-access Sequences 1 2 3 4 5 Indexes 1 Description cimArpEntry 1.3.6.1.4.1.6247.4.5.2.2.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimArpConfig(2).cimArpTabl e(2).
PAGE 351
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.116 CIMARPIPADDRESS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimArpIpAddress 1.3.6.1.4.1.6247.4.5.2.2.1.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimArpConfig(2).cimArpTabl e(2).cimArpEntry(1).
PAGE 352
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.118 CIMARPPHYSTYPE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description cimArpPhysType 1.3.6.1.4.1.6247.4.5.2.2.1.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimArpConfig(2).cimArpTabl e(2).cimArpEntry(1).
PAGE 353
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.119 CIMARPROWSTATUS Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 3 4 5 6 Description cimArpRowStatus 1.3.6.1.4.1.6247.4.5.2.2.1.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimProtocols(5).cimArpConfig(2).cimArpTabl e(2).cimArpEntry(1).
PAGE 354
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.120 CIMREDUNDANCY Name OID Full path Module Parent Prev sibling Next sibling Child Type cimRedundancy 1.3.6.1.4.1.6247.4.6 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRedundancy(6) CIMController cimController cimProtocols cimOperMaint cimCurrentRedundantState OBJECT-IDENTIFIER 13.7.
PAGE 355
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.122 CIMLOCALUNITMANAGEMENTIPADDRESS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimLocalUnitManagementIpAddress 1.3.6.1.4.1.6247.4.6.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRedundancy(6).
PAGE 356
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.124 CIMREDUNDANTTRAFFICIPADDRESS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimRedundantTrafficIpAddress 1.3.6.1.4.1.6247.4.6.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRedundancy(6).
PAGE 357
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.126 CIMFORCEUNITOFFLINE Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimForceUnitOffline 1.3.6.1.4.1.6247.4.6.6 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimRedundancy(6).
PAGE 358
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.128 CIMAPPVERSION Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimAppVersion 1.3.6.1.4.1.6247.4.7.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimOperMaint(7).
PAGE 359
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.130 CIMRESET Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimReset 1.3.6.1.4.1.6247.4.7.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimOperMaint(7).
PAGE 360
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.132 CIMREMOTEPORTBDEVICEADDRESS Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimRemotePortBDeviceAddress 1.3.6.1.4.1.6247.4.7.4.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimOperMaint(7).cimRemotePortBConfig(4).
PAGE 361
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.134 CIMREMOTEPORTBFORMAT Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 3 Description cimRemotePortBFormat 1.3.6.1.4.1.6247.4.7.4.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimOperMaint(7).cimRemotePortBConfig(4).
PAGE 362
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.136 CIMSTATISTICS Name OID Full path Module Parent Prev sibling Child Type cimStatistics 1.3.6.1.4.1.6247.4.8 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8) CIMController cimController cimOperMaint cimSatelliteTransmitStatistics OBJECT-IDENTIFIER 13.7.
PAGE 363
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.139 CIMSATELLITETRANSMITENTRY Name OID Full path Module Parent Child Type Numerical syntax Base syntax Composed syntax Status Max-access Sequences 1 2 3 4 5 6 7 Indexes 1 Description cimSatelliteTransmitEntry 1.3.6.1.4.1.6247.4.8.1.1.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimSatelliteTransmitStatistics (1).cimSatelliteTransmitTable(1).
PAGE 364
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.140 CIMSATELLITETRANSMITINDEX Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimSatelliteTransmitIndex 1.3.6.1.4.1.6247.4.8.1.1.1.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimSatelliteTransmitStatistics (1).cimSatelliteTransmitTable(1).cimSatelliteTransmitEntry(1).
PAGE 365
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.142 CIMSATELLITETRANSMITTOTALPACKETSTRANSMITTED Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimSatelliteTransmitTotalPacketsTransmitted 1.3.6.1.4.1.6247.4.8.1.1.1.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimSatelliteTransmitStatistics (1).cimSatelliteTransmitTable(1).
PAGE 366
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.144 CIMSATELLITETRANSMITMINDATARATE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimSatelliteTransmitMinDataRate 1.3.6.1.4.1.6247.4.8.1.1.1.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimSatelliteTransmitStatistics (1).cimSatelliteTransmitTable(1).
PAGE 367
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.146 CIMSATELLITETRANSMITAVGDATARATE Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cimSatelliteTransmitAvgDataRate 1.3.6.1.4.1.6247.4.8.1.1.1.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimSatelliteTransmitStatistics (1).cimSatelliteTransmitTable(1).
PAGE 368
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.148 CIMUNICASTIPPACKETSTOSATELLITE Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimUnicastIpPacketsToSatellite 1.3.6.1.4.1.6247.4.8.2.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 369
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.150 CIMMULTICASTIPPACKETSTOSATELLITE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimMulticastIpPacketsToSatellite 1.3.6.1.4.1.6247.4.8.2.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 370
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.152 CIMBROADCASTIPPACKETSTOSATELLITE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimBroadcastIpPacketsToSatellite 1.3.6.1.4.1.6247.4.8.2.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 371
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.154 CIMPACKETSFROMSATELLITE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimPacketsFromSatellite 1.3.6.1.4.1.6247.4.8.2.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 372
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.156 CIMTOTALIPPACKETSTOETHERNET Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimTotalIpPacketsToEthernet 1.3.6.1.4.1.6247.4.8.2.9 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 373
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.159 IPOPTIONPACKETSRECEIVED Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimIpOptionPacketsReceived 1.3.6.1.4.1.6247.4.8.2.11 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 374
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.161 CIMDROPPEDPACKETSTTLEXPIRED Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimDroppedPacketsTTLExpired 1.3.6.1.4.1.6247.4.8.2.13 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 375
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.163 CIMDROPPEDPACKETSNOROUTE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimDroppedPacketsNoRoute 1.3.6.1.4.1.6247.4.8.2.15 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 376
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.165 CIMDROPPEDPACKETSFILTERED Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimDroppedPacketsFiltered 1.3.6.1.4.1.6247.4.8.2.17 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 377
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.167 CIMDROPPEDPACKETSNOARPENTRY Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimDroppedPacketsNoArpEntry 1.3.6.1.4.1.6247.4.8.2.19 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 378
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.169 CIMDROPPEDPACKETSBADIPVERSION Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimDroppedPacketsBadIpVersion 1.3.6.1.4.1.6247.4.8.2.21 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 379
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.171 CIMDROPPEDPACKETSQOS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimDroppedPacketsQos 1.3.6.1.4.1.6247.4.8.2.23 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 380
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.7.173 CIMDROPPEDPACKETSDROPPEDBUFFERS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cimDroppedPacketsDroppedBuffers 1.3.6.1.4.1.6247.4.8.2.25 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cimController(4).cimStatistics(8).cimIpRoutingStatistics(2).
PAGE 381
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.8 CIM-550 MIB TREE 1 --- iso 1.3 --- org 1.3.6 --- dod 1.3.6.1 --- internet 1.3.6.1.4 --- private 1.3.6.1.4.1 --- enterprises 1.3.6.1.4.1.6247 --- comtech 1.3.6.1.4.1.6247.5 --- cim550 1.3.6.1.4.1.6247.5.1 --- cim550Objects 1.3.6.1.4.1.6247.5.1.1 --- cim550SystemInfo 1.3.6.1.4.1.6247.5.1.1.1 --- cim550EquipmentID (INTEGER) 1.3.6.1.4.1.6247.5.1.1.2 --- cim550UnitSerialNumber (INTEGER) 1.3.6.1.4.1.6247.5.1.1.
PAGE 382
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 1.3.6.1.4.1.6247.5.1.3.3 --- cim550RxDemodType (INTEGER) 1.3.6.1.4.1.6247.5.1.3.4 --- cim550RxFECType (INTEGER) 1.3.6.1.4.1.6247.5.1.3.5 --- cim550RxFECCodeRate (INTEGER) 1.3.6.1.4.1.6247.5.1.3.6 --- cim550RxSpecInv (INTEGER) 1.3.6.1.4.1.6247.5.1.3.7 --- cim550RxDescrambler (INTEGER) 1.3.6.1.4.1.6247.5.1.3.8 --- cim550RxClockMode (INTEGER) 1.3.6.1.4.1.6247.5.1.3.9 --- cim550RxBufferSize (INTEGER) 1.3.6.1.4.1.6247.5.1.3.
PAGE 383
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 1.3.6.1.4.1.6247.5.1.7.6 --- cim550RedundancyState (INTEGER) 1.3.6.1.4.1.6247.5.1.7.7 --- cim550ModemUnitFaults (INTEGER) 1.3.6.1.4.1.6247.5.1.7.8 --- cim550ModemTxTrafficFaults (INTEGER) 1.3.6.1.4.1.6247.5.1.7.9 --- cim550ModemRxTrafficFaults (INTEGER) 1.3.6.1.4.1.6247.5.1.8 --- cim550Logs 1.3.6.1.4.1.6247.5.1.8.1 --- cim550ClearEventsLog (INTEGER) 1.3.6.1.4.1.6247.5.1.8.2 --- cim550NumberUnreadEvents (INTEGER) 1.3.6.1.4.1.6247.5.1.8.
PAGE 384
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 1.3.6.1.4.1.6247.5.2.3.8 --- oduUnitLNAFaultLogic (INTEGER) 1.3.6.1.4.1.6247.5.2.3.9 --- oduUnitRedundancyMode (INTEGER) 1.3.6.1.4.1.6247.5.2.3.10 --- oduUnitRedForceSwitch (INTEGER) 1.3.6.1.4.1.6247.5.2.4 --- oduTxParameters 1.3.6.1.4.1.6247.5.2.4.1 --- oduTxFrequency (INTEGER) 1.3.6.1.4.1.6247.5.2.4.2 --- oduTxAttenuation (INTEGER) 1.3.6.1.4.1.6247.5.2.4.3 --- oduTxAmplifier (INTEGER) 1.3.6.1.4.1.6247.5.2.4.
PAGE 385
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9 CIM-550 MIB 13.9.1 CIM550 Name OID Full path Module Parent Child Type Organization Last updated Contact info Description cim550 1.3.6.1.4.1.6247.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5) CIM550 comtech cim550Objects MODULE-IDENTITY Comtech EF Data 200205071700Z 2114 West 7th Street Tempe, AZ 85281 USA CIM-550 Satellite Modem 13.9.
PAGE 386
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.4 CIM550EQUIPMENTID Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cim550EquipmentID 1.3.6.1.4.1.6247.5.1.1.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550SystemInfo(1).
PAGE 387
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.6 CIM550SOFTWAREREVISION Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cim550SoftwareRevision 1.3.6.1.4.1.6247.5.1.1.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550SystemInfo(1).
PAGE 388
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.8 CIM550DEVICEDATE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cim550DeviceDate 1.3.6.1.4.1.6247.5.1.1.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550SystemInfo(1).
PAGE 389
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.10 CIM550LOCALREMOTESTATE Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description cim550LocalRemoteState 1.3.6.1.4.1.6247.5.1.1.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550SystemInfo(1).
PAGE 390
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.12 CIM550TXFREQUENCY Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 2 Description cim550TxFrequency 1.3.6.1.4.1.6247.5.1.2.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550TxParameters(2).
PAGE 391
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.14 CIM550TXMODTYPE Name OID Full path cim550TxModType 1.3.6.1.4.1.6247.5.1.2.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550TxParameters(2).
PAGE 392
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.15 CIM550TXFECTYPE Name OID Full path cim550TxFECType 1.3.6.1.4.1.6247.5.1.2.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550TxParameters(2).
PAGE 393
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.16 CIM550TXFECCODERATE Name OID Full path cim550TxFECCodeRate 1.3.6.1.4.1.6247.5.1.2.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550TxParameters(2).
PAGE 394
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.18 CIM550TXSCRAMBLER Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description cim550TxScrambler 1.3.6.1.4.1.6247.5.1.2.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550TxParameters(2).
PAGE 395
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.20 CIM550TXPOWERLEVEL Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cim550TxPowerLevel 1.3.6.1.4.1.6247.5.1.2.9 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550TxParameters(2).
PAGE 396
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.22 CIM550RXPARAMETERS Name OID Full path Module Parent Prev sibling Next sibling Child Type cim550RxParameters 1.3.6.1.4.1.6247.5.1.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550RxParameters(3) CIM550 cim550Objects cim550TxParameters cim550InterfaceParameters cim550RxFrequency OBJECT-IDENTIFIER 13.9.
PAGE 397
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.24 CIM550RXDATARATE Name OID Full path cim550RxDataRate 1.3.6.1.4.1.6247.5.1.3.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550RxParameters(3).
PAGE 398
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.26 CIM550RXFECTYPE Name OID Full path cim550RxFECType 1.3.6.1.4.1.6247.5.1.3.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550RxParameters(3).
PAGE 399
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.27 CIM550RXFECCODERATE Name OID Full path cim550RxFECCodeRate 1.3.6.1.4.1.6247.5.1.3.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550RxParameters(3).
PAGE 400
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.29 CIM550RXDESCRAMBLER Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description cim550RxDescrambler 1.3.6.1.4.1.6247.5.1.3.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550RxParameters(3).
PAGE 401
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.31 CIM550RXBUFFERSIZE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 3 4 5 Description cim550RxBufferSize 1.3.6.1.4.1.6247.5.1.3.9 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550RxParameters(3).
PAGE 402
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.33 CIM550RXEBNOALARMPOINT Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cim550RxEbnoAlarmPoint 1.3.6.1.4.1.6247.5.1.3.11 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550RxParameters(3).
PAGE 403
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.35 CIM550IFIMPEDANCE Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description cim550IfImpedance 1.3.6.1.4.1.6247.5.1.4.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550InterfaceParameters(4).
PAGE 404
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.37 CIM550UTILITYPARAMETERS Name OID Full path Module Parent Prev sibling Next sibling Child Type cim550UtilityParameters 1.3.6.1.4.1.6247.5.1.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550UtilityParameters(5) CIM550 cim550Objects cim550InterfaceParameters cim550AupcParameters cim550UnitFramingMode OBJECT-IDENTIFIER 13.9.
PAGE 405
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.39 CIM550EDMACADDRESS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cim550EdmacAddress 1.3.6.1.4.1.6247.5.1.5.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550UtilityParameters(5).
PAGE 406
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.41 CIM550RECENTERBUFFER Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 Description cim550RecenterBuffer 1.3.6.1.4.1.6247.5.1.5.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550UtilityParameters(5).
PAGE 407
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.43 CIM550UNITALARMMASK Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cim550UnitAlarmMask 1.3.6.1.4.1.6247.5.1.5.6 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550UtilityParameters(5).
PAGE 408
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.45 CIM550UNITCONFIGLOAD Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cim550UnitConfigLoad 1.3.6.1.4.1.6247.5.1.5.8 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550UtilityParameters(5).
PAGE 409
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.47 CIM550AUPCPARAMETERS Name OID Full path Module Parent Prev sibling Next sibling Child Type cim550AupcParameters 1.3.6.1.4.1.6247.5.1.6 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550AupcParameters(6) CIM550 cim550Objects cim550UtilityParameters cim550StatusParameters cim550AupcEnable OBJECT-IDENTIFIER 13.9.
PAGE 410
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.49 CIM550AUPCCONTROLPARAMETERS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cim550AupcControlParameters 1.3.6.1.4.1.6247.5.1.6.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550AupcParameters(6).
PAGE 411
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.51 CIM550TXPOWERLEVELINCREASE Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cim550TxPowerLevelIncrease 1.3.6.1.4.1.6247.5.1.6.4 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550AupcParameters(6).
PAGE 412
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.53 CIM550RXEBNO Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 2 Description cim550RxEbno 1.3.6.1.4.1.6247.5.1.7.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550StatusParameters(7).
PAGE 413
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.55 CIM550RXFREQUENCYOFFSET Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 2 Description cim550RxFrequencyOffset 1.3.6.1.4.1.6247.5.1.7.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550StatusParameters(7).
PAGE 414
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.57 CIM550RXBER Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cim550RxBER 1.3.6.1.4.1.6247.5.1.7.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550StatusParameters(7).
PAGE 415
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.59 CIM550MODEMUNITFAULTS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description cim550ModemUnitFaults 1.3.6.1.4.1.6247.5.1.7.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550StatusParameters(7).
PAGE 416
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.61 CIM550MODEMRXTRAFFICFAULTS Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Size list 1 Description cim550ModemRxTrafficFaults 1.3.6.1.4.1.6247.5.1.7.9 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550StatusParameters(7).
PAGE 417
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.63 CIM550CLEAREVENTSLOG Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 Description cim550ClearEventsLog 1.3.6.1.4.1.6247.5.1.8.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550Logs(8).
PAGE 418
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.65 CIM550RETRIEVENEXT5EVENTS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cim550RetrieveNext5Events 1.3.6.1.4.1.6247.5.1.8.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(624 7).cim550(5).cim550Objects(1).cim550Logs(8).
PAGE 419
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.67 CIM550CLEARSTATISTICSLOG Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 Description cim550ClearStatisticsLog 1.3.6.1.4.1.6247.5.1.8.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550Logs(8).
PAGE 420
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.69 CIM550RETRIEVENEXT5STATISTICS Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Description cim550RetrieveNext5Statistics 1.3.6.1.4.1.6247.5.1.8.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550Logs(8).
PAGE 421
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.72 CIM550MODEMUNITFAULTSNOTIFICATION Name OID Full path Module Parent Next sibling Type Objects 1 Description cim550ModemUnitFaultsNotification 1.3.6.1.4.1.6247.5.1.9.0.624751 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).cim550Objects(1).cim550Notifications(9).cim550N otificationsPrefix(0).
PAGE 422
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.75 ODUOBJECTS Name OID Full path Module Parent Prev sibling Child Type oduObjects 1.3.6.1.4.1.6247.5.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2) CIM550 cim550 cim550Objects oduSelect OBJECT-IDENTIFIER 13.9.76 ODUSELECT Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description oduSelect 1.3.
PAGE 423
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.78 ODUMODELNUMBERSOFTWAREVER Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description oduModelNumberSoftwareVer 1.3.6.1.4.1.6247.5.2.2.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduSystemInfo(2).
PAGE 424
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.80 ODUDEVICETIME Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description oduDeviceTime 1.3.6.1.4.1.6247.5.2.2.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).co mtech(6247).cim550(5).oduObjects(2).oduSystemInfo(2).
PAGE 425
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.82 ODUCIRCUITID Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description oduCircuitID 1.3.6.1.4.1.6247.5.2.2.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduSystemInfo(2).
PAGE 426
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.84 ODUUNITMUTEMODE Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description oduUnitMuteMode 1.3.6.1.4.1.6247.5.2.3.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduUnitParameters(3).
PAGE 427
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.86 ODUUNITAUTOFAULTRECOVERY Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description oduUnitAutoFaultRecovery 1.3.6.1.4.1.6247.5.2.3.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduUnitParameters(3).
PAGE 428
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.88 ODUUNITREFOSCADJUST Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description oduUnitRefOscAdjust 1.3.6.1.4.1.6247.5.2.3.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduUnitParameters(3).
PAGE 429
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.90 ODUUNITLNACURRENTWINDOW Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 3 4 5 6 7 8 Description oduUnitLNACurrentWindow 1.3.6.1.4.1.6247.5.2.3.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduUnitParameters(3).
PAGE 430
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.91 ODUUNITLNAFAULTLOGIC Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description oduUnitLNAFaultLogic 1.3.6.1.4.1.6247.5.2.3.8 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduUnitParameters(3).
PAGE 431
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.93 ODUUNITREDFORCESWITCH Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 Description oduUnitRedForceSwitch 1.3.6.1.4.1.6247.5.2.3.10 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduUnitParameters(3).
PAGE 432
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.95 ODUTXFREQUENCY Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description oduTxFrequency 1.3.6.1.4.1.6247.5.2.4.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduTxParameters(4).
PAGE 433
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.97 ODUTXAMPLIFIER Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description oduTxAmplifier 1.3.6.1.4.1.6247.5.2.4.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduTxParameters(4).
PAGE 434
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.99 ODUTXSLOPEMODE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description oduTxSlopeMode 1.3.6.1.4.1.6247.5.2.4.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduTxParameters(4).
PAGE 435
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.101 ODUTXGAINOFFSET Name OID Full path Module Parent Prev sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description oduTxGainOffset 1.3.6.1.4.1.6247.5.2.4.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduTxParameters(4).
PAGE 436
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.103 ODURXFREQUENCY Name OID Full path Module Parent Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description oduRxFrequency 1.3.6.1.4.1.6247.5.2.5.1 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduRxParameters(5).
PAGE 437
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.105 ODURXMUTE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Value list 1 2 Description oduRxMute 1.3.6.1.4.1.6247.5.2.5.3 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduRxParameters(5).
PAGE 438
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.107 ODURXSLOPEVALUE Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description oduRxSlopeValue 1.3.6.1.4.1.6247.5.2.5.5 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduRxParameters(5).
PAGE 439
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.109 ODUUNITSTATUS Name OID Full path Module Parent Prev sibling Next sibling Child Type oduUnitStatus 1.3.6.1.4.1.6247.5.2.6 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduUnitStatus(6) CIM550 oduObjects oduRxParameters oduLogs oduOnlineState OBJECT-IDENTIFIER 13.9.
PAGE 440
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.111 ODUMAINTENANCEPARAMETERS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description oduMaintenanceParameters 1.3.6.1.4.1.6247.5.2.6.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduUnitStatus(6).
PAGE 441
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.113 ODULOGS Name OID Full path Module Parent Prev sibling Next sibling Child Type oduLogs 1.3.6.1.4.1.6247.5.2.7 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduLogs(7) CIM550 oduObjects oduUnitStatus oduNotifications oduClearEventsLog OBJECT-IDENTIFIER 13.9.
PAGE 442
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.115 ODUNUMBERUNREADEVENTS Name OID Full path Module Parent Prev sibling Next sibling Type Numerical syntax Base syntax Composed syntax Status Max-access Size list 1 Description oduNumberUnreadEvents 1.3.6.1.4.1.6247.5.2.7.2 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduLogs(7).
PAGE 443
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.IOM 13.9.117 ODUNOTIFICATIONS Name OID Full path Module Parent Prev sibling Child Type oduNotifications 1.3.6.1.4.1.6247.5.2.8 iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).comtech(6 247).cim550(5).oduObjects(2).oduNotifications(8) CIM550 oduObjects oduLogs oduNotificationsPrefix OBJECT-IDENTIFIER 13.9.118 ODUNOTIFICATIONSPREFIX Name OID Full path Module Parent Child Type oduNotificationsPrefix 1.3.6.1.4.1.6247.5.2.8.
PAGE 444
CiM-550 IP Enabled Satellite Modem SNMP interface Rev. 2 CD/CIM550.
PAGE 445
Chapter 14. CiM IP Module Checkout and Fault Isolation 14.1 INTRODUCTION CAUTION This equipment contains parts and assemblies sensitive to damage by ESD. Use ESD precautionary procedures when touching, removing, or inserting PCBs. This Chapter is for testing and troublshooting CiM IP module and assumes that the base satellite modem is correctly configured and functioning properly. 14.
PAGE 446
CiM-550 IP Enabled Satellite Modem CiM IP Module Checkout & Fault Isolation Rev. 2 CD/CIM550.IOM 14.2.
PAGE 447
CiM-550 IP Enabled Satellite Modem CiM IP Module Checkout & Fault Isolation Rev. 2 CD/CIM550.IOM 14.2.3 TRANSMIT AND RECEIVE IF CONFIGURATION Step Procedure 1 Configure the transmit and receive IF parameters on CiM 1 and CiM 2 via the front panel. Note: The IF parameters can also be set via console menu, Telnet, web interface and SNMP but for this exercise, it is recommended that the front panel be used. 2 Set the TxPower to minimum level.
PAGE 448
CiM-550 IP Enabled Satellite Modem CiM IP Module Checkout & Fault Isolation Rev. 2 CD/CIM550.IOM 14.2.5 MAIN MENU Figure 14-1. Main Menu To use this onterface, select the appropriate sub-menu or the entry by pressing the character indicated at the right. Enter x to return to the previous menu. 14.2.6 RESTORING FACTORY DEFAULT CONFIGURATION The following sections in this guide assume that the CiM is still in factory default configuration for IP.
PAGE 449
CiM-550 IP Enabled Satellite Modem CiM IP Module Checkout & Fault Isolation Rev. 2 CD/CIM550.IOM At this point you should be able to ping CiM 1 from PC 1: 10 ping 172.16.10.10 11 ping 10.1.1.1 14.2.1.2 ROUTE TABLE Step Procedure 1 From Main Menu, select Route Table sub-menu. 2 Enter 1 to configure the first route 3 Enter a suitable name 4 Set IP Address to 172.17.10.0 5 Set Number of Subnet Bits to 24 6 Enter the next hop IP address which is CiM 2’s HDLC IP Address, 10.1.1.2 14.2.1.
PAGE 450
CiM-550 IP Enabled Satellite Modem CiM IP Module Checkout & Fault Isolation Rev. 2 CD/CIM550.IOM 14.2.8 CIM 2 CONFIGURATION Disconnect RJ-11 end of the console cable from CiM 1 and connect it to CiM 2. 14.2.8.1 SETTING IP ADDRESS(ES) Step Procedure 1 From the Main Menu select Network Configuration sub-menu. 2 Set Ethernet IP Address to 172.17.10.10. 3 Set Subnet Prefix Length to 24. 4 Set HDLC IP Address to 10.1.1.2. 5 Set RX – Enable/Disable and TX – Enable/Disable to Enable.
PAGE 451
CiM-550 IP Enabled Satellite Modem CiM IP Module Checkout & Fault Isolation Rev. 2 CD/CIM550.IOM 14.3 TROUBLESHOOTING IP MODULE Use the following troubleshooting steps if unable to succesfully complete “CiM IP Module Checkout”. Step 1 Problem No Ping response from the locally connected PC to the CiM ethernet port. ICMP resonse is ‘Request timed out’ or ‘Destination host unreachable’. Action 1) Verify correct IP address/subnet on PC and CiM. 2) Verify ethernet connection – cables, hub, etc.
PAGE 452
CiM-550 IP Enabled Satellite Modem CiM IP Module Checkout & Fault Isolation Rev. 2 CD/CIM550.IOM 3) Continue sending constant ping from the PC 1 to PC 2. In the CiM 2, go to Operations Maintenance/Diagnostics. Enable ‘Dump Packets received from Satellite Interface”. Verify that the Pings are being received by observing 1 packet on CLI every second. If not displayed; a) Reverify PC 2 and CiM 2 settings. b) Verify IF link between modems for proper settings and carrier quality (RX signal leval, Eb/No, etc).
PAGE 453
Application Note - Flash Upgrading the CiM-550 Satellite Modems Flash Upgrade Overview Many Comtech EF Data modems use "flash memory" internally, eliminating the need for physically replacing firmware. The advantages of using flash are many, but perhaps the greatest benefit is realized by not having to disassemble the modems to replace an integrated circuit. New firmware can simply be uploaded to the units from an external PC. The CiM family of modems have base modem firmware (M&C) and CiM module firmware.
PAGE 454
CiM-550 IP Enabled Satellite Modem Flash Upgrading Rev. 2 CD/CIM550.IOM Downloading Flash Upgrades from the Web Base Modem (M&C or BULK Firmware) The latest firmware releases and a free software utility are available on the Comtech EF Data web site (http://www.comtechefdata.com). This utility is designed to run under Windows 95/98 or Windows NT/2000/XP and provides all of the support required to perform a Comtech EF Data firmware reflash.
PAGE 455
CiM-550 IP Enabled Satellite Modem Flash Upgrading Rev. 2 CD/CIM550.IOM CiM IP Module Firmware Perform the CiM IP Module upgrade by using an FTP (File Transfer Protocol) utility program. The latest firmware releases are available on the Comtech EF Data web site (http://www.comtechefdata.com). An FTP utility is required to perform a Comtech EF Data firmware reflash. If web downloading is not available or practical, contact the Network Customer Support department (cimfss@comtechefdata.
PAGE 456
How to Perform a Flash Upgrade for the CiM IP Module Step 1 Procedure On the PC, double-click the .exe or .zip flash upgrade file to uncompress its contents. Ensure that the following unzipped files are located in the directory: fw9781-1x.mpp, where "x" is the version number (FPGA). fw9630-1x.mpp, where "x" is the version number (Application). fw9630-2x.mib, where "x" is the version number (CIMController mib). fw9630-3x.mib, where "x" is the version number (CiM550.mib). fw9630-4x.
PAGE 457
Index EasyConnect? for non-IP traffic ..................5 EB/NO MEASUREMENT ......................493 EDMAC CHANNEL ...............................489 EGP Group...............................................165 EIA-232 Operation...................................465 EIA-232....................................................434 EIA-485....................................................433 End Of Packet ..........................................438 Ethernet Interface Connector ...................
PAGE 458
CiM-550 IP Enabled Satellite Modem Index Rev. 2 CD/CIM550.IOM Setup ........................................................465 SNMP Group ...........................................165 SNMP INTERFACE................................151 SNMP Interface .......................................151 SNMP Operations ......................................18 Software .......................................................3 Specifications...............................................7 Standard Features.............
PAGE 459
METRIC CONVERSIONS Units of Length Unit Centimeter Inch Foot Yard Mile Meter Kilometer Millimeter 1 centimeter — 0.3937 0.03281 0.01094 6.214 x 10-6 0.01 — — 1 inch 2.540 — 0.08333 0.2778 1.578 x 10-5 0.254 — 25.4 1 foot 30.480 12.0 — 0.3333 1.893 x 10-4 0.3048 — — 1 yard 91.44 36.0 3.0 — 5.679 x 10-4 0.9144 — — 1 meter 100.0 39.37 3.281 1.094 6.214 x 10-4 — — — 1 mile 1.609 x 105 6.336 x 104 5.280 x 103 1.760 x 103 — 1.609 x 103 1.
PAGE 460
2114 WEST 7TH STREET TEMPE ARIZONA 85281 USA 480 • 333 • 2200 PHONE 480 • 333 • 2161 FAX