Installation Guide

ManualsBrandsModa Flame ManualsElectric FireplacesGrand 95 in. Pebble Electric Wall Mounted Fireplace in Black

Houston 50 Inch Electric Wall

Mounted Fireplace Black / White

Model Number:MFE5050BK

Model Number:MFE5050WH

Read these instructions carefully before attempting to assemble, install, operate or maintain

the product described. Protect yourself and others by observing all safety information. Failure

to comply with instructions could result in personal injury and / or property damage. Retain

instructions for future reference.

Website: www.ModaFlame.com

IMPORTANT INSTRUCTIONS & OPERATING MANUAL

Summary of content (9 pages)

PAGE 1
IMPORTANT INSTRUCTIONS & OPERATING MANUAL Houston 50 Inch Electric Wall Mounted Fireplace Black / White Model Number:MFE5050BK Model Number:MFE5050WH Read these instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and / or property damage. Retain instructions for future reference. Website: www.ModaFlame.
PAGE 2
GENERAL SAFETY INFORMATION When using this fireplace, basic precautions should always be taken to reduce the risk of fire, electric shock and injury to persons, including the following: CAUTION – Due to the high temperature, keep electrical cords, drapery and other furnishings at least 3 feet from the front, side and rear of the fireplace. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22.
PAGE 3
23. Faulty wall outlet connections may cause the wall outlet to overheat. Be sure that the fireplace plug properly fits into the outlet before each use. During use, make sure the fireplace plug does not overheat. If necessary, have a qualified electrician check and / or replace the wall outlet. 24. Do not place the fireplace near a bed for objects such as pillows or blankets can fall off the bed and be ignited by the fireplace. 25. Never clean this fireplace while it is plugged in.
PAGE 4
Sr. No Item Description Quantity 001 Carton 1 002 Foam Protection (Left Bottom) 1 003 Electric Fireplace 1 004 Foam Protection (Left Top) 1 005 Mounting Screws and Wall Plugs ST5x40 6 006 Instruction Manual 1 007 Remote Control 1 008 Foam Protection (Right Top) 1 009 Cable Plug 1 010 Foam Protection (Right Bottom) 1 Helpful Advice Before Installation         Please retain all packaging until you have checked and counted all the parts and other package contents.
PAGE 5
Tools Needed   Power drill Screwdriver Installation        Do not connect the fireplace to the power supply until properly fixed to the wall and the instructions are carefully read. Make sure the area to be drilled does not have any hidden electrical wires or water and gas pipes. The minimum distances must be observed as shown in the diagrams below. During installation of the fireplace, avoid any possible damage to concealed cables. Please be careful when drilling holes.
PAGE 6
Step Two      Make sure the area to be drilled does not have any hidden electrical wires or water and gas pipes. The wall fixings provided is for concrete walls only; please use suitable fixings for your wall type. If in doubt, contact a qualified hardware expert. Place the three bulged screw tubes into the drilled holes and then screw in the self-tapping screws. Screw the extended wooden screws into the 0.20” screw anchors so they protrude out of the wall to angle the fireplace.
PAGE 7
Turning On   Plug the fireplace into a power outlet. Turn on the power switch which is located on the right side of the fireplace.
PAGE 8
Power Switch    Plug the fireplace into a power outlet. The fireplace is now in Standby mode. Press the button once to turn on the fireplace and flame effect. An indicator light will light up to indicate that the function is on. This will also turn on the flame effect. Press the button once to turn off the flame effect. This will put the fireplace back into Standby mode. Heat Control    Press the “Heat Control” button once for the low heat setting.
PAGE 9
Cleaning & Maintenance      Disconnect from the power supply before attempting any maintenance or cleaning in order to reduce the risk of fire, electric shock to persons or damage to property. Warning - Always disconnect from the power supply before cleaning fireplace. For general cleaning, use a soft, clean duster. Never use abrasive cleaners. The glass viewing screen should be cleaned thoroughly with a soft cloth. Do NOT use proprietary glass cleaners.