Aviator Flush Installation Instructions works with the Google Assistant
Please read and save these instructions before installation DO NOT RETURN TO STORE 2 Aviator Flush Instructions FH-W1811
General Inquiries For all questions about your ceiling fan please read all included instructions, installation procedures, troubleshooting guidelines and warranty information before starting installation For missing parts or general inquiries call our trained technical staff at: 1-866-810-6615 option 0 MON-FRI 8AM-8PM EST Email: customerservice@modernforms.com Or live chat at modernforms.com Fan Support For fast service have the following information below when you call: 1. Model Name and Number 2.
Safety Rules For operation, maintenance, and troubleshooting information, visit http://modernforms.com/fan-support/ To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a licensed electrician. The fan must be mounted with a minimum of 7 ft. (2.
WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product is designed for use only with the supplied parts and/or accessories designated for use with this product by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern Forms could result in personal injury or property damage and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.
Get Smart... works with the Google Assistant Integrates seamlessly with: devices you already own Wet location-listed to the strictest UL/cUL safety regulations.
Contents 1. Mounting Options 10 2. Installing the Mounting Bracket 12 3. Attaching The Fan Blades 12 4. Attaching Decorative Lower Cap 12 5. Making the Electrical Connections 14 6. Installing the Wall Control 16 7. Finishing the Installation 18 8. Installing the LED Luminaire Module 20 9. Controlling the Fan 22 10. Factory Reset 24 11. Breeze Mode 24 12. Application 24 13.
Package Contents 1. Blade Set of 3 RPL-F1811-54-BD-** 2. Blade Collector Ring 3. Hanger Plate RPL-F1811-HANGER-** 4. Hanger Gasket 6. Bottom Cap (Aluminum) 7. Control Receiver W/ Hardware RPL-F1811-54-REC 8. Wall Control W/Hardware F-WCBT-WT 5. Motor Assembly ** denotes finish code of fan *** denotes blade sweep of fan Hardware Bag RPL-AVIATORFH-PART • 3/16” x .375” Flat head screws (5 pcs) -Blade Collector Ring • ø 4.4x9.
Hanging Weight: 13 lbs MAC ID 3 IMPORTANT: Please make note of the MAC ID on the receiver and keep it in a safe place.
1. Mounting Options CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning. To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning. If there isn’t an existing UL/cUL listed outlet box, please refer to the following instructions. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials.
2 1 Support Brace Joist Outlet Box Outlet Box 4 3 SLOPED CEILING MAX 30° ANGLE Provides Strong Support Mounting Bracket Recessed Outlet Box 4 3 Mounting Screw FH - W 1 8 1 1 Outlet Box UL/cUL Mounting 120V Wir Mounting Screws Aviator Flush Instructions 11
2. Installing the Mounting Bracket REMEMBER to turn off power at the breaker. Follow the steps below to hang your fan properly: 1. Disconnect power to the fan location at the breaker. A licensed electrician must install the fan. 2. There are four screws on top of the motor assembly. Remove two that are on the opposite of each other and save for section 10. Loosen remaining two. 3. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in Figure 2. 4.
2 3 3A 4 FH - W 1 8 1 1 Aviator Flush Instructions 13
5. Making the Electrical Connections WARNING: Installation of this fan requires that a three-conductor cable (including ground wire) which should run between ceiling and wall outlet box. WARNING: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire. Insert the receiver into the mounting bracket with the flat side of the receiver facing the ceiling (Fig. 5). Motor to Receiver & Receiver to housing supply wires (Fig. 5A).
5 1. 1 Mounting Bracket 2. Receiver 2 5A Outlet box Black (hot) Black (“AC IN L”) Receiver White (neutral) Green (Ground) White (“AC IN N”) Green (Ground) To hanger ball Green (Ground) To hanger bracket White (for light) Blue (for light) Red (to motor) Gray (to motor) Yellow (to motor) Green (Ground) Yellow (motor) Gray (motor) Red (motor) White (for light) Blue (for light) Follow the steps below to connect the fan to your household wiring. Use the plastic wire nuts with your fan.
6. Installing the Wall Control NOTE: Wall Control not included. A bluetooth wall control accessory can be purchased separately. 1. Connect the green wire marked “GROUND” from the wall control to the copper wire from the wall outlet box that feeds back to the circuit breaker – important for proper fan function (Fig. 7). 2. Connect the black wire marked “LINE IN” from the wall control to the black LINE VOLTAGE wire from the wall outlet box that feeds back to the circuit breaker (Fig. 7). 3.
6A 1 2 3 1. Wall Outlet 2. Wall Control 3. Wall Mounting 4. Mounting 5. Wallplate 4 5 Multi-location wiring Individually pair each of the wall controls with the fan receiver using the pairing instruction. See page 27 if Applicable Green White Red Wall Controller 3 Black Green White Red Black Green Red White Black HOT IN Wall Controller 2 Green to Fan White to Fan Black to Fan Wall Controller 1 Green Maximum of 2 fans can operate on a circuit through the wall transmitter.
7. Finishing the Installation 1. Secure all wire connections with supplied wire ties to assist in fan installation. 2. Tuck connections neatly into ceiling outlet box. 3. Remove the motor assembly from the hook on the mounting bracket. Position the motor up to the hanger plate and attach using two screws through the two key slots in the top of the motor housing (Fig. 7). Note: Make sure the receiver sits flat and does not interfere with the hook. 4.
7 FH - W 1 8 1 1 Aviator Flush Instructions 19
8. Installing the LED Luminaire Module WARNING: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box. NOTE: If you do not plan to install the luminaire module with your fan at this time, skip this step. 1. Remove the three screws from the LED wire storage cap, keep the cap for future use when not using the luminaire (Fig. 8). 1. Install the LED mounting plate using 3 screws removed from step 1 (Fig. 8A). 1.
8 8A 8B 8C 8D FH - W 1 8 1 1 Aviator Flush Instructions 21
9. Controlling the Fan Your fan is pre-paired. If you need to pair your fan refer to (Fig. 9C). A: Light On/Off, Bright/Dim +/- B: Fan On/Off, Fan Speed +/C: Reverse Button (Summer and Winter Modes) Air-Gap Switch: Pull tab to power off in case of emergency. Not necessary for normal fan operation (only included with wall control). NOTE: Your fan features 6 speeds. An audible tone will indicate when the speed is increased or decreased.
9 9A A B C Air-Gap Switch* Wall Control * Air-Gap Switch only included with wall control Remote Control Summer Mode Winter Mode (Counter-Clockwise) (Clockwise) 9B Fan On/Off Light On/Off Press and hold button for 4 seconds. Fan On/Off: Press and hold Press and hold button for 4 seconds. Fan Direction Press and hold button for 4 seconds. button for 4 seconds. The LED on the remote will flash green and all connected fans will beep to indicate the message has been received.
10. Factory Reset NOTE: Changes to your Wi-Fi network settings (SSID or Security Passphrase) will prevent your fan from connecting to the cloud. You can re-establish connectivity by performing a Wi-Fi Reset and using the Modern Forms app to reconfigure the fan to connect to the network with the new settings. 11. Breeze Mode 1. Breeze Mode mimics the natural ebb and flow of winds in nature by varying the fan speed. NOTE: Breeze Mode always rotates your fan in the Summer (CCW) direction 2.
9C 10 Pairing Unpairing Fan Wi-Fi Reset Press and hold buttons for 10-15 seconds. To purge, press and hold buttons for 4 seconds.
13.
FH - W 1 8 1 1 Aviator Flush Instructions 27
Certificate of Warranty Congratulations on your new purchase. Your new Modern Forms Smart Fan is engineered to make life easier every day. Modern Forms creates future-forward fans and luminaires that provide energy savings and outstanding efficiency. Our dedication to doing things the right way goes beyond our love for amazing products.
parte del distribuidor y, en consecuencia, cualquier daño consecuencial o costo de mano de obra que surja de un defecto se excluye expresamente. Esta garantía no se aplicará a los productos que hayan sido alterados, instalados incorrectamente, mal manejados o mal utilizados. La notificación de un defecto por escrito debe ser recibida por Modern Forms dentro de los cinco (5) años a partir de la fecha de compra (o según el período de tiempo indicado en el material).
FH -W 1811 modernforms.
