Wynd Installation Instructions works with the Google Assistant
Please read and save these instructions before installation DO NOT RETURN TO STORE 2 Wynd Instructions FR-W1801
General Inquiries For all questions about your ceiling fan please read all included instructions, installation procedures, troubleshooting guidelines and warranty information before starting installation. For missing parts or general inquiries call our trained technical staff at: 1-866-810-6615 option 0 MON-FRI 8AM-8PM EST Email: customerservice@modernforms.com Or live chat at modernforms.com Fan Support For fast service have the following information below when you call: 1. Model Name and Number 2.
Safety Rules For operation, maintenance, and troubleshooting information, visit http://modernforms.com/fan-support/ To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a licensed electrician. The fan must be mounted with a minimum of 7 ft. (2.
WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product is designed for use only with the supplied parts and/or accessories designated for use with this product by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern Forms could result in personal injury or property damage and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.
Get Smart... works with the Google Assistant Integrates seamlessly with: devices you already own Wet Location-listed to the strictest UL/cUL safety regulations.
Contents 1. Mounting Options 10 2. Installing the Mounting Bracket 12 3. Attaching the Fan Blade 12 4. Assembling the Fan 14 5. Hanging the Fan 16 6. Making the Electrical Connections 18 7. Installing the Optional Wall Control 20 7. Installing the Optional Wall Control 22 8. Finishing the Installation 22 9. Controlling the Fan 24 10. Reset 26 11. Breeze Mode 26 12. Application 26 13. Accessories 28 14.
Package Contents 1. Blade Set of 5 (42” / 52” / 60”) RPL-F1801-**-BD-** 2. Mounting Bracket Downrod Assembly RPL-HGR-ASM-** 3. Coupling Cover RPL-COU-CVR-** 4. Canopy & Canopy Ring RPL-CAN-CYL-** 5. Motor Housing 6. Adapter Plate 7. Luminaire Module F4IN-120V-R1-30 8. Luminaire Cover RPL-F1801-COVER-** 9. Acrylic Shade RPL-F1801-GLA 10. Control receiver w/Hardware (***) F-R3-1801-0** 11.
Hanging Weight: 20 lbs MAC ID IMPORTANT: Please make note of the MAC ID on the receiver and keep it in a safe place.
1. Mounting Options CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning. If there isn’t an existing UL/cUL listed outlet box, please refer to the following instructions. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and support structure must be able to fully support the moving weight of the fan (at least 35 lbs/15.9 kg). Do not use plastic outlet boxes.
1 1. 3 Support Brace 2. Outlet Box 1 3. Joist 2 1A 1. Outlet Box 1 1B Support Ceiling Max 30° Angle 1 1. 2 3 Support Brace 2. Mounting Bracket 3. Recess Outlet Box 1C 1.
2. Installing the Mounting Bracket CAUTION: Remember to disconnect the power at the circuit breaker. 1. Remove 1 set screw from mounting bracket and set aside for use in Finishing the Installation. 2. Pass supply wires through mounting bracket and secure to outlet box. Verify supply wire colors and designations (Fig. 2A). 3. Secure the mounting bracket to the ceiling outlet box with the screws and washers provided with your outlet box. 3. Attaching the Fan Blade 1.
2 2A To Switch B A 1 1 (HOT) (Neutral) To Switch 2 3 A (No Neutral) 2 (HOT)/ Switch 1. Mounting Bracket 2. Screw 2 (Ground) *Bare or Green (Ground) *Bare or Green 1.1 cUL Listed Electrical Box 2. Mounting Screws HARDWARE USED: Outlet Box Screws and Washers (2) (outlet box screws not included) D 3. 120V Wires 3 3 1 1. Slot C 2. Blade (RPL-F1801-**-BD-**) 3.
4. Assembling the Fan CAUTION: Failure to properly install the cotter pin and/or tighten the set screws could result in the fan loosening and possibly falling. NOTE: Screws for Adapter plate (6) are preinstalled on the fan motor assembly on the small ring at the center of the blades. Remove blue packing ring if present. 1. Remove one screw from the inner ring on the motor assembly and loosen the other 2 (Fig. 4). 2.
4 4A 1 1. 3 screws for adapter plate 4B 4C UNLESS OTHERWISE SPECIFIED: DIMENSIONS ARE IN INCHES TOLERANCES: FRACTIONAL ANGULAR: MACH BEND TWO PLACE DECIMAL THREE PLACE DECIMAL 3 USED ON APPLICATION 2 DATE TITLE: ENG APPR. MFG APPR. COMMENTS: MATERIAL NEXT ASSY CHECKED Q.A. INTERPRET GEOMETRIC TOLERANCING PER: PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF .
5. Hanging the Fan CAUTION: Failure to properly install the cotter pin and/or tighten the set screws could result in the fan loosening and possibly falling. NOTE: Make sure all screws are tightened and that wires are not twisted. 1. Remove screw from hanger ball. Remove hanger ball and cross pin (Fig. 5). 2. Loosen 2 screws, clevis pin and cotter pin (Fig. 5). NOTE: Confirm all connection points on the molex connector are tight and secure. If any wires are loose, it may cause the fan to not function. Fig.
5 5A 4 1 2 3 6 5 7 5B 1. 8 Canopy 2. Canopy Ring 3. Coupling Cover 4. Molex Connector 5. Clevis Pin 9 6. Cotter Pin 7. Motor Housing Screws 8. Wood Screw 9.
6. Making the Electrical Connections WARNING: Installation of this fan requires that a three-conductor cable (including ground wire) which should run between ceiling and wall outlet box. WARNING: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire. Take note of Mac ID on page 9 before inserting the receiver into the mounting bracket with the flat side of the receiver facing the ceiling (Fig. 6).
6 1. Mounting Bracket 2.
7. Installing the Optional Wall Control 1. Connect the green wire marked “GROUND” from the wall control to the copper wire from the wall outlet box that feeds back to the circuit breaker – important for proper fan function (Fig. 7). 2. Connect the black wire marked “LINE IN” from the wall control to the black LINE VOLTAGE wire from the wall outlet box that feeds back to the circuit breaker (Fig. 7). 3.
7A 1 2 3 1. Wall Outlet 2. Wall Control 3. Wall Mounting Plate 4. Mounting Plate Screws 5. Wallplate 4 5 Multi-location wiring Individually pair each of the wall controls with the fan receiver using the pairing instruction. See page 25.
7. Installing the Optional Wall Control 1. If replacing a pre-existing two switch setup, Modern forms wall switches only require a hot, neutral, and ground to control both the light and the fan. Use supply wires to provide the controller its needed wiring, and choose either traveller wire previously installed to bring power to the fan. Extra wires should be safely and properly capped. NOTE: Prexisting wiring may only provide power. Verify supply wiring has a true neutral for operation.
Replacing Pre-Existing Switch 8 1 2 3 1. Outlet Box 2. Hanger Bracket 4 3. Screws 4. Canopy 5.
9. Controlling the Fan Your fan was delivered to you with the included control already paired to your fan. A: Light On/Off, Bright/Dim B: Fan On/Off, Speed Up/Down C: Season (Summer/Winter) Air-Gap Switch: Pull tab to power off in case of emergency. Not necessary for normal fan operation (only included with wall control). NOTE: Your fan features 6 speeds. An audible tone will indicate when the speed is increased or decreased. When the fan has reached the minimum/maximum speed level the fan will beep twice.
9 9A A B C Air-Gap Switch* Wall Control * Air-Gap Switch only included with wall control Remote Control Summer Mode Winter Mode (Counter-Clockwise) (Clockwise) 9B Fan On/Off Light On/Off Fan Direction Press and hold button for 4 seconds. Press and hold button for 4 seconds. Press and hold button for 4 seconds. Fan On/Off: Press and hold button for 4 seconds. The LED on the remote will flash green and all connected fans will beep to indicate the message has been received.
10. Reset If advised by fan support, you can reset your fan to factory settings by referring to (Fig. 10A) or (Fig. 10B). NOTE: If you change your Wi-Fi settings (SSID or Security Passphrase) you will require a Wi-Fi reset. Refer to Fig. 9 and then use the Modern Forms app to connect your fan to the new network. 11. Breeze Mode Breeze Mode mimics the natural ebb and flow of winds in nature by varying the fan speed. NOTE: Breeze Mode always rotates your fan in the Summer direction. 1.
9C 10 Pairing Unpairing Fan Wi-Fi Reset Press and hold buttons for 10-15 seconds To purge, press and hold buttons for 4 seconds Press and hold the and for 10 seconds until LED blinks green and receiver emits 2 long beeps 10B 10A Factory Reset Receiver Factory Reset Press and hold buttons for 10 seconds until the fan emits 3 beeps indicating the reset Press the reset button on the receiver until the receiver emits 3 beeps indicating the reset Scan and follow prompts for multilingual instruction
13.
Sloped Ceiling Kit Designed to accommodate buildings with steeper sloped ceilings up to 45° or 12/12 pitch XF-SCK Coupler Connects two downrods XF-I Downrod XF-12 - 12” Downrod | XF-18 - 18” Downrod XF-24 - 24” Downrod | XF-36 - 36” Downrod XF-48 - 48” Downrod | XF-60 - 60” Downrod XF-72 - 72” Downrod FR- W 1 8 0 1 Wynd Instructions 29
14. Troubleshooting My Fan Will Not Start 1. Check main and branch circuit fuses or circuit breakers. 2. Check line wire connections to fan and switch wire connections in the switch housings. CAUTION: Make sure the main power is turned off! My Fan is Noisy 1. Allow for 24-hour break-in period. Most noises associated with a new fan will go away during this time period. 2. Check to make sure the screws which attached to the blades (and blade arms when applicable) are tight. 3.
My Fan is not producing Enough Air Movement If possible, please consider using a longer than included downrod. My remote or wall control is not controlling my fan Verify that the fan is receiving power by power cycling the fan. To do this: 1. Cut power to the fan via standard On/Off wall switch, or the breaker if standard wall switch is not applicable. 2. Wait at least 10 seconds, and then restore power. 3. The fan will power on in Pairing mode for 3 minutes. 4. Press and hold 10-15 seconds.
14. Troubleshooting cont. My Fan failed to join the Wi-Fi network 1. Make sure you entered the correct Wi-Fi password and your mobile device is connected to the same network you attempted to connect the fan. 2. Make sure you are within the router manufacturer’s specified range. If all of these steps have failed - please power cycle your fan and router and retry. What is power cycling and how do I power cycle my fan? Power cycling is the act of temporaily removing the power source for your fan.
What is Pairing? Pairing is the process of connecting your Modern Forms remote or wall control to your fan. Your fan comes pre-paired to your included remote control. However, if you want additional controls for your fan or if you’re replacing a control, refer to the pairing and unpairing section of the instructions. What is a Factory Reset? Factory Reset is a restore of the fans original settings.
Certificate of Warranty Congratulations on your new purchase. Your new Modern Forms Smart Fan is engineered to make life easier every day. Modern Forms creates future-forward fans and luminaires that provide energy savings and outstanding efficiency. Our dedication to doing things the right way goes beyond our love for amazing products.
parte del distribuidor y, en consecuencia, cualquier daño consecuencial o costo de mano de obra que surja de un defecto se excluye expresamente. Esta garantía no se aplicará a los productos que hayan sido alterados, instalados incorrectamente, mal manejados o mal utilizados. La notificación de un defecto por escrito debe ser recibida por Modern Forms dentro de los cinco (5) años a partir de la fecha de compra (o según el período de tiempo indicado en el material).
FR-W 1801 modernforms.
