M O RPHE U S II & I II FR-W1812- 6 0 L ; FR- W1 8 1 3 - 6 0 L s INSTALLATION INSTRUCTIONS WET DC MOTOR SMART works with the Google Assistant modernforms.
All Modern Forms Smart Fans are: WET SMART Durably finished and Rated for interior and exterior use Able to coordinate with smart devices for voice-activated and thermostat control Wet location-listed to the strictest ETL/cETL safety regulations DC MOTOR Quiet, reliable, and up to 70% more efficient than AC fans Wi-Fi and RF enabled for unlimited control APP INSTRUCTIONS AND SMART HOME DEVICE INTEGRATION modernforms.
TABLE OF CONTENTS 1. SAFETY RULES............................................................................................................................................... 4 2. FTC ENERGY GUIDE & SPECIFICATION...................................................................................................... 5 3. TOOLS AND MATERIALS REQUIRED........................................................................................................... 5 4. PACKAGE CONTENTS.................................
1. SAFETY RULES For operation, maintenance, and troubleshooting information, visit modernforms.com/help. 1. 2. 3. 4. 5. 6. 7. 8. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. box and ungrounded conductor on the other side of the outlet box. 9. All set screws must be checked and re-tightened where necessary before installation.
2. FTC ENERGY GUIDE & SPECIFICATION FAN FAN SIZE VOLTS N.W. (lbs) G.W. (lbs) STANDARD ELECTRICITY AIR FLOW ENERGY COSTS* FAN EFFICACY 60” 120 6.85 10.67 High Speed 25W 6543 CFM $7/yr 258.6 CFM/W Weighted Average 15W 3881 CFM $4/yr 266 CFM/W Morpheus II FAN FAN SIZE VOLTS N.W. (lbs) G.W. (lbs) STANDARD ELECTRICITY AIR FLOW ENERGY COSTS* FAN EFFICACY 60” 120 7.10 10.92 High Speed 31W 7490 CFM $9/yr 243.
4. PACKAGE CONTENTS REF. DESCRIPTION A B Unpack your fan and check the contents. You should have the following items: USE PART NO. Blade Set of 2 (2Bl.) Morpheus II only RPL-F1812-60-BD-** Blade Set of 3 (3Bl.) Morpheus III only RPL-F1813-60-BD-** Hanger Assembly RPL-HGR-ASM-** - Mounting Bracket - Downrod Asm.
4. PACKAGE CONTENTS (cont.) REF. DESCRIPTION M PART NO. Hardware Bag Φ4 * 18mm Flat Head Screw (Customed 15mm) (13) 1/4"-20thread x11mm+S Phil/Slotted Screw (13) Φ6.5x19x2mm Flat Washer (1) RPL-MORPHEUS-PARTS 3/16"(Φ5.2x8.4x1.
5. MOUNTING OPTIONS Joist Support brace If there isn’t an existing UL/cUL listed mounting box, please refer to the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support structure must be able to fully support the moving weight of the fan (at least 35 lbs). Do not use plastic outlet boxes.
6. INSTALL THE MOUNTING BRACKET REMEMBER to disconnect the power by removing fuses or turning off circuit breaker. Follow the steps below to hang your fan properly: 1. Disconnect power at the breaker to the fan location. A licensed electrician must install the fan (Fig. 5). 2. FIGURE 5 Remove 1 of 2 screws from the bottom of mounting bracket and save for use in section 9. Loosen the other screw (Fig. 6). 3.
7. ATTACHING THE FAN BLADES 1. 5 FIGURE 8 Remove and discard the 2 pre-installed screws on the motor as shown (Fig. 8). 2. Attach the fan blades with the blade screws provided (Fig. 9). 3. For two bladed model position spacer between blades as shown (Fig. 9 : Two Blades). 4. Turn the fan motor assembly over and install the blade collector ring with the screws provided (Fig. 10).
8. INSTALLING THE LIGHT KIT PLATE 1. Remove one of the three mounting plate screws from the mounting ring and loosen the other two screws (Do not remove). (Fig. 11) 2. Place the key holes in the light kit plate over the two screws previously loosened from the mounting ring. Turn the light kit plate until it locks in place at the narrow section of the key holes (Fig. 12). 3. Securely tighten the two light kit plate screws previously removed.
9. HANGING THE FAN 1. Remove the clevis pin and cotter pin and loosen the two collar screws from the motor collar (Fig. 13). 2. Feed motor wires through coupling cover, canopy ring, and 8 Downrod Assembly canopy 3. Feed motor wire through downrod assembly. 4. Thread the downrod assembly onto motor collar. Align the holes Canopy of the downrod and collar and insert the cotter pin and clevis pin. Canopy Ring Tighten the two collar screws (Fig. 13).
9. HANGING THE FAN (cont.) 1. Carefully lift the fan motor assembly up to the mounting bracket 9 and seat the hanger ball in the mounting bracket socket. Make sure the tab on the mounting bracket socket is properly seated in the groove in the hanger ball. Rotate the socket assembly until the ball drops and locks into the hanger bracket screw (Fig. 14). 2. Secure the safety cable to the building structure using spring washer, flat washer, and wood screw provided (Fig. 15).
10. MAKING THE ELECTRICAL CONNECTIONS REMEMBER to disconnect the power by removing fuses or turning off circuit breaker. WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. Mounting bracket WARNING: Installation of this fan requires that a two-conductor cable with ground wire be run between ceiling and wall outlet box.
10. MAKING THE ELECTRICAL CONNECTIONS (cont.) Outlet box Motor to receiver electrical connections: (Fig. 17) 1. Connect the hanger ball/downrod assembly ground wire, mounting bracket ground wire and receiver ground wire to the ground White (neutral) Green (Ground) Black (hot) Black (“AC IN L”) White (“AC IN N”) wire in outlet box. Green (Ground) WARNING: Failure to connect ground wires could result in poor fan control functionality. 2. MOTOR” from the receiver. 3.
11. INSTALLING THE WALL CONTROL WARNING: Remember to shut the power off at the circuit breaker or fuse box. Wall control to wall outlet box electrical connections: (Fig. 18) 1. Connect ground wires - Important for proper control function. 2. Connect the black wire marked “LINE IN” from the control to the black LINE VOLTAGE wire from the outlet box that feeds back to the breaker. 3. Connect the red wire from the control to the black wire from the wall outlet box that feeds up to the fan. 4.
11. INSTALLING THE WALL CONTROL (cont.) 1. Carefully tuck the wire connections inside the junction box. Wall control Secure the wall control with the two wall control mounting screws provided (Fig. 19). 2. Wall outlet box Wall mounting plate Attach the wall mounting plate over the wall control and secure with the two wall mounting plate screws provided. 3. Fasten the wall plate to the wall mounting plate. NOTE: A maximum of 2 fans can operate on a circuit through the wall control.
12. FINISHING THE INSTALLATION 1. Secure all wire connections with supplied wire ties to assist in canopy installation. 2. Tuck connections neatly into ceiling outlet box. Position the motor up to the hanger plate and attach the motor using two screws through the two key slots (Fig. 20). 3. Slide the canopy up to the hanger bracket and place the key hole on the canopy over the screw on the hanger bracket. Turn canopy until it locks in place at the narrow section of the key holes (Fig. 20). 4.
13. INSTALLING THE LED LUMINAIRE MODULE (OPTIONAL) WARNING: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box. NOTE: If you do not plan to install the luminaire module with your fan at this time, skip to Step 4. 1. Remove 1 of the 3 screws from the outer perimeter of the adapter plate and keep it for future use. Loosen the other 2 screws (Do not remove). FIGURE 21 2.
13. INSTALLING THE LED LUMINAIRE MODULE (OPTIONAL) NOTE: Add metal light cover if you do not need lighting function or prefer a different aesthetic (Fig 24). NOTE: Do not connect the LED connector wires if you are using the metal light plate. 5. If installing the optional metal light cover, make sure it is securely tightened.
14. WALL CONTROL OPERATING INSTRUCTIONS Your DC brushless motor is equipped with an intuitive wall control. Restore power to ceiling fan and test the wall control as below for proper operation. Pairing the Wall Control to Your Fan Your fan is pre-paired at the factory, No pairing is necessary. Wall Control Button Functions These seven buttons are used to set the fan speed as follows: Button: turn the light ON or OFF Press/Hold to increase the desired light level.
14. WALL CONTROL OPERATING INSTRUCTIONS (cont.) NOTE: A maximum of 2 fans can operate on a circuit through the wall transmitter. NOTE: A maximum of 12 fans can operate on a circuit through an on/off switch or breaker when utilizing the Modern Forms app for the fan control (without the wall control in the circuit). Summer Mode - (Counter-clockwise) A downward airflow creates a cooling effect as shown in Fig. 26. This allows you to set your air conditioner on a warmer setting without affecting your comfort.
15. APPLICATION In addition to the included wall control, you can control the fan through the Modern Forms app. 1. To use the app, download it for free from the App Store or Google Play. 2. Open the app to create your account. You can also log in with your FIGURE 28 FIGURE 29 Facebook or Google account. 3. Next, set up a WiFi connection. You’ll need the SSID and WiFi password for the network you want to connect to. 4.
16. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check all electrical connections and ensure proper contact. WARNING: Before checking any electrical connections, ensure electricity has been turned off at the circuit breaker before beginning. 2. 3. 4. 5. 6. FR-W1812; FR-W1813 Check wall control LED indicator light. If LED indicator light is not illuminated when pushing a button, it is not transmitting a signal.
16. TROUBLESHOOTING (cont.) Problem Fan sounds noisy. Solution 1. 2. 3. 4. 5. Fan wobbles. Allow a 24-hour “breaking in” period. Most noise associated with a new fan will disappear during this time. Make sure all motor housing screws are securely fastened. Make sure the screws that attach the fan blades to the fan are securely fastened. Make sure the screws securing the LED luminaire module are securely fastened.
17.
PRODUCT DOWNROD FR- W1 8 1 2 ; FR- W 1 8 1 3 MODEL DESCRIPTION FINISH XF-12 12 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-18 18 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-24 24 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-36 36 in downrod XF-48 48 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-60 60 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-72 72 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB
Get Smart works with the Google Assistant The Modern Forms app synchronizes seamlessly with smart home devices you already own. To learn more go to modernforms.com/mfappins Free App Download Sync with our exclusive Modern Forms App to control fan speed, use smart features like Adaptive Learning, create groups and reduce energy costs.
Español For instructions in Spanish please visit the link below. Para obtener instrucciones en español, visite el siguiente enlace. www.modernforms.com/fan-instructions-espanol Français For instructions in French please visit the link below. Pour obtenir des instructions en français, veuillez visiter le lien ci-dessous. www.modernforms.
FR-W1812; FR-W1813 30
FR- W1 8 1 2 ; FR- W 1 8 1 3 31
FR-W1 8 1 2 ; FR- W 1 8 1 3 modernforms.