W O O DY FR- W 1 8 1 4 - 6 0 L s INSTALLATION INSTRUCTIONS WET DC MOTOR SMART works with the Google Assistant modernforms.
All Modern Forms Smart Fans are: WET SMART Durably finished and Rated for interior and exterior use Able to coordinate with smart devices for voice-activated and thermostat control Wet location-listed to the strictest ETL/cETL safety regulations DC MOTOR Quiet, reliable, and up to 70% more efficient than AC fans Wi-Fi and RF enabled for unlimited control APP INSTRUCTIONS AND SMART HOME DEVICE INTEGRATION modernforms.
TABLE OF CONTENTS 1. SAFETY RULES..............................................................................................................................................4 2. FTC ENERGY GUIDE & SPECIFICATION.....................................................................................................5 3. TOOLS AND MATERIALS REQUIRED..........................................................................................................5 4. PACKAGE CONTENTS.......................................
1. SAFETY RULES For operation, maintenance, and troubleshooting information, visit modernforms.com/help. 1. 2. 3. 4. 5. 6. 7. 8. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. box and ungrounded conductor on the other side of the outlet box. 9. All set screws must be checked and re-tightened where necessary before installation.
2. FTC ENERGY GUIDE & SPECIFICATION FAN FAN SIZE VOLTS N.W. (lbs) G.W. (lbs) Woody 60” 120 8.42 12.02 STANDARD ELECTRICITY AIR FLOW ENERGY COSTS* FAN EFFICACY High Speed 42W 8840 CFM $12/yr 209.5 CFM/W Weighted Average 23W 5160 CFM $6/yr 22 CFM/W NOTE: These are approximate measures. They do not include amps and wattage used by the light kit. 3.
4. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: REF. DESCRIPTION PART NO.
4. PACKAGE CONTENTS (cont.) REF. DESCRIPTION K Hardware Bag PART NO. 3/16"x24mm Phil/Slotted Pan Head Screw (10) Φ5x14x1mm Flat Washer (10) Φ4.7x14x2mm rubber washer (10) RPL-WOODY-PARTS 3/16"x32mm Phil/Slotted Pan Head Screw (7) Φ6.5x19x2mm Flat Washer (1) 3/16"(Φ5.2x8.4x1.
5. MOUNTING OPTIONS Joist If there isn’t an existing UL/cUL listed mounting box, please refer to the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support structure must be able to fully support the moving weight of the fan (at least 35 lbs). Do not use plastic outlet boxes.
6. INSTALLING THE MOUNTING BRACKET REMEMBER to disconnect the power by removing fuses or turning off circuit breaker. Follow the steps below to hang your fan properly: 1. Disconnect power at the breaker to the fan location. A licensed electrician must install the fan (Fig. 5). 2. FIGURE 5 Remove 1 of 2 screws from the bottom of mounting bracket and save for use in section 9. Loosen the other screw (Fig. 6). 3.
7. ATTACHING THE FAN BLADES 1. Attach each fan blade with the flat washers, rubber washers, and screws provided. Install the flat washer onto the screw, then the Screw rubber washer. The rubber washer will be in contact with the wood blades (Fig. 8). 2. Flat washer Attach the upper blade holder using the 6 screws provided Rubber washers (Fig. 9).
8. HANGING THE FAN 1. Remove the clevis pin and cotter pin, and loosen the two collar screws from the motor collar (Fig. 10). 2. Feed motor wires through coupling cover, canopy ring, and canopy. 3. Feed motor wires through downrod assembly. 4. Thread the downrod assembly onto motor collar. Align the holes of Canopy Canopy Ring downrod and collar and insert the cotter pin and clevis pin. Tighten the two collar screws (Fig. 10). 5. Slide coupling cover to rest on motor housing.
8. HANGING THE FAN (cont.) 1. Carefully lift the fan motor assembly up to the mounting bracket and seat the hanger ball in the mounting bracket socket. Make sure the tab on the mounting bracket socket is properly seated in the groove in the hanger ball (Fig. 11). Rotate the socket assembly until the ball drops and locks into the hanger bracket screw. 2. Secure the safety cable to the building structure using a wood screw (not included) (Fig. 12).
9. MAKING THE ELECTRICAL CONNECTIONS REMEMBER to disconnect the power by removing fuses or turning off circuit breaker. WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. Mounting bracket WARNING: Installation of this fan requires that a two-conductor cable with ground wire should be run between ceiling and wall outlet box.
9. MAKING THE ELECTRICAL CONNECTIONS (cont.) Motor to receiver electrical connections: (Fig. 14) 1. Connect the hanger ball/downrod assembly ground wire, mounting bracket ground wire and receiver ground wire to the Outlet box White (neutral) Green (Ground) Black (hot) Black (“AC IN L”) White (“AC IN N”) ground wire in outlet box. Green (Ground) To hanger ball WARNING: Failure to connect ground wires could result in poor fan control functionality. 2. “TO MOTOR” from the receiver. 3.
10. INSTALLING THE WALL CONTROL WARNING: Remember to shut the power off at the circuit breaker or fuse box. Wall control to wall outlet box electrical connections: (Fig. 18) 1. Connect ground wires - Important for proper control function. 2. Connect the black wire marked “LINE IN” from the control to the black LINE VOLTAGE wire from the outlet box that feeds back to the breaker. 3. Connect the red wire from the control to the black wire from the wall outlet box that feeds up to the fan. 4.
10. INSTALLING THE WALL CONTROL (cont.) 1. Carefully tuck the wire connections inside the junction box. Secure the wall control with the two wall control mounting screws provided (Fig. 19). 2. Attach the wall mounting plate over the wall control and secure Wall control Wall outlet box Wall mounting plate with the two wall mounting plate screws provided. 3. Fasten the wall plate to the wall mounting plate. NOTE: A maximum of 2 fans can operate on a circuit through the wall control.
11. FINISHING THE INSTALLATION 1. Secure all wire connections with supplied wire ties to assist in canopy installation. 2. Tuck connections neatly into ceiling outlet box. 3. Slide the canopy up to the hanger bracket and place the key hole on the canopy over the screw on the hanger bracket. Turn canopy until Canopy it locks in place at the narrow section of the key holes (Fig. 17). 4. Align the circular hole on canopy with the remaining hole on the Canopy ring hanger bracket.
12. INSTALLING THE LED LUMINAIRE MODULE (OPTIONAL) WARNING: Before starting installation, disconnect the power by turning FIGURE 18 off the circuit breaker or removing the fuse at fuse box. Turning power off using the fan switch is not sufficient to prevent electric shock. NOTE: If you do not plan to install the luminaire module with your fan at this time, skip to step 4. NOTE: Do not connect the LED connector wires if you are using the metal light cover. 1.
13. WALL CONTROL OPERATING INSTRUCTIONS Your DC brushless motor is equipped with an intuitive wall control. Restore power to ceiling fan and test the wall control as below for proper operation. Pairing the Wall Control to Your Fan Your fan is pre-paired at the factory, No pairing is necessary. Wall Control Button Functions These seven buttons are used to set the fan speed as follows: Button: turn the light ON or OFF Press/Hold to increase the desired light level.
13. WALL CONTROL OPERATING INSTRUCTIONS (cont.) NOTE: A maximum of 2 fans can operate on a circuit through the wall control. NOTE: A maximum of 12 fans can operate on a circuit through an on/off switch or breaker when utilizing the Modern Forms app for the fan control (without the wall control in the circuit). Summer Mode - (Counter-clockwise) A downward airflow creates a cooling effect as shown in Fig. 22. This allows you to set your air conditioner on a warmer setting without affecting your comfort.
14. APPLICATION In addition to the included wall control, you can control the fan through the Modern Forms app. 1. To use the app, download it for free from the App Store or Google Play. 2. Open the app to create your account. You can also log in with your FIGURE 24 FIGURE 25 Facebook or Google account. 3. Next, set up a WiFi connection. You’ll need the SSID and WiFi password for the network you want to connect to. 4.
15. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check wall control LED indicator light. If LED is not illuminated when pushing a button, it is not transmitting a signal. Please check power to wall switch and all electrical connections. 3. Assure that there are no more than 2 fans operating on a circuit through the wall control control.
16.
PRODUCT DOWNROD FR-W1814 MODEL DESCRIPTION FINISH XF-12 12 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-18 18 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-24 24 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-36 36 in downrod XF-48 48 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-60 60 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-72 72 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT All ou
Get Smart The Modern Forms app synchronizes seamlessly with smart home devices you already own. To learn more go to modernforms.com/mfappins works with the Google Assistant Free App Download Sync with our exclusive Modern Forms App to control fan speed, use smart features like Adaptive Learning, create groups and reduce energy costs. modernforms.
FR-W1814 26
FR- W1 8 1 4 27
FR- W 1 8 1 4 modernforms.