WI NDF L O W E R FR-W1815- 6 0 L ; FR- W1 8 1 5 - 8 0 L s INSTALLATION INSTRUCTIONS WET DC MOTOR SMART works with the Google Assistant modernforms.
All Modern Forms Smart Fans are: WET SMART Durably finished and Rated for interior and exterior use Able to coordinate with smart devices for voice-activated and thermostat control Wet location-listed to the strictest ETL/cETL safety regulations DC MOTOR Quiet, reliable, and up to 70% more efficient than AC fans Wi-Fi and RF enabled for unlimited control APP INSTRUCTIONS AND SMART HOME DEVICE INTEGRATION modernforms.
TABLE OF CONTENTS 1. SAFETY RULES............................................................................................................................................... 4 2. FTC ENERGY GUIDE & SPECIFICATIONS.................................................................................................... 5 3. TOOLS AND MATERIALS REQUIRED........................................................................................................... 5 4. PACKAGE CONTENTS..................................
1. SAFETY RULES For operation, maintenance, and troubleshooting information, visit modernforms.com/help. 1. 2. 3. 4. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning. 9. All set screws must be checked and re-tightened where necessary before installation.
2. FTC ENERGY GUIDE & SPECIFICATIONS FAN FAN SIZE VOLTS N.W (lbs) G.W (lbs) Windflower 60” 120 38.92 45.33 FAN FAN SIZE VOLTS N.W (lbs) G.W (lbs) Windflower 80” 120 41.5 48.07 STANDARD ELECTRICITY AIR FLOW ENERGY COST* FAN EFFICACY High Speed 48W 12428 CFM $13/yr 261.1 CFM/W Weighted Average 29W 8398 CFM $8/yr 290 CFM/W STANDARD ELECTRICITY AIR FLOW ENERGY COST* FAN EFFICACY High Speed 45W 12950 CFM $13/yr 287.
4. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items: REF. DESCRIPTION PART NO.
5. MOUNTING OPTIONS Support Brace Joist If there isn’t an existing UL/cUL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs). Do not use plastic outlet boxes.
6. HANGING THE FAN REMEMBER to turn off power at the breaker. Follow the steps below to hang your fan properly: 1. Disconnect power at the breaker to the fan location. A licensed electrician must install the fan (Fig. 5). 2. FIGURE 5 Remove 1 of 2 screws from the bottom of mounting bracket and save for use in section 9. Loosen the other screw (Fig. 6). 3. Pass the 120-volt supply wires through the center hole in the ceiling mounting bracket as shown in (Fig. 7). 4.
6. HANGING THE FAN (cont.) 1. Carefully remove and discard the blue shipping cap from the top of the motor housing, ensuring that the lead wires and safety cable do not become twisted. 2. Cross Pin Hanger Ball Set Screw Remove the 3 screws from the blue shipping cap on the Downrod bottom of the motor housing and keep them for use with the light kit adapter plate. Discard the blue shipping cap. 3.
6. HANGING THE FAN (cont.) 1. Slip the coupling cover, canopy screw cover (painted side face down), and canopy (opened side up) onto the downrod Motor Wires Safety Cable Downrod Canopy (Fig. 10). Coupling cover goes all the way to the bottom. 2. Carefully reinstall the hanger ball onto the downrod, being sure that the cross pin is in the correct position, the setscrew Canopy Screw Cover Coupling Cover is tightened and wires are not twisted (Fig. 10). 3.
7. MAKING THE ELECTRICAL CONNECTIONS WARNING: To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. WARNING: Installation of this fan requires that a three-conductor cable (including ground wire) should be run between ceiling and wall Mounting Bracket outlet box. WARNING: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire.
7. MAKING THE ELECTRICAL CONNECTIONS (cont.) Motor to receiver electrical connections (Fig. 13): 1. Connect the hanger ball/downrod assembly ground wire, mounting bracket ground wire and receiver ground wire to the Outlet Box White (neutral) Green (ground) Black (hot) Black (“AC IN L”) White (“AC IN N”) ground wire in outlet box. Green (Ground) To hanger ball WARNING: Failure to connect ground wires could result in poor fan control functionality. 2.
8. INSTALLING THE WALL CONTROL Wall control to wall outlet box electrical connections (Fig. 14): WARNING: Remember to shut the power off at the circuit breaker or fuse box. 1. Connect ground wires - Important for proper control function. 2. Connect the black wire marked “LINE IN” from the control to the black LINE VOLTAGE wire from the outlet box that feeds back to the breaker. 3. Connect the red wire from the control to the black wire from the wall outlet box that feeds up to the fan. 4.
8. INSTALLING THE WALL CONTROL (cont.) 1. Carefully tuck the wire connections inside the junction box. Wall Control Secure the wall control with the two wall control mounting screws provided (Fig. 15). 2. Wall Outlet Box Attach the wall mounting plate over the wall control and Wall Mounting Plate secure with the two wall mounting plate screws provided. 3. Fasten the wall plate to the wall mounting plate. NOTE: A maximum of 2 fans can operate on a circuit through the wall control.
9. FINISHING THE INSTALLATION 1. Secure all wire connections with supplied wire ties to assist in canopy installation. 2. Tuck connections neatly into ceiling outlet box. 3. Slide the canopy up to hanger bracket and place the key hole on the canopy over the screw on the hanger bracket. Outlet Box Hanger Bracket Turn canopy until it locks in place at the narrow section Screws of the key holes (Fig. 16). 4. Align the circular hole on canopy with the remaining hole Canopy on the hanger bracket.
10. ATTACHING THE FAN BLADES CAUTION: To avoid personal injury or damage to the fan or other items, we recommend hanging the fan before attaching the fan blades. 1. Insert fan blades through the slots in the motor housing. Align the holes in the fan blades with the fan motor assembly holes Slot and secure with the fan blade attachment screws and blade caps Blade Blade Cap provided (Fig.17). Screws With Rubber Washers NOTE: Make sure fan blades are straight before fastening.
13. INSTALLING THE LED LUMINAIRE MODULE WARNING: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box. Turning power off using the fan switch is not sufficient to prevent electric shock. NOTE: If you do not plan to install the luminaire module with your fan at this time, skip to step 5. 1. Remove 1 of the 3 screws from the outer perimeter of the adapter plate and keep it for future use. Loosen the other 2 screws (Do not remove). 2.
13. INSTALLING THE LED LUMINAIRE MODULE (cont.) 5. If installing the optional metal light cover, make sure it is securely tightened (Fig. 20). NOTE: Add metal light cover if you do not need lighting function or prefer a different aesthetic (Fig. 20). NOTE: Do not connect the LED connector wires if you are using the metal light cover.
14. WALL CONTROL OPERATING INSTRUCTIONS Your DC brushless motor is equipped with an intuitive wall control. Restore power to ceiling fan and test the wall control as below for proper operation. Pairing the Wall Control to Your Fan Your fan is pre-paired at the factory, o pairing is necessary. Wall Control Button Definitions These seven buttons are used to set the fan speed as follows: Button: turn the light ON or OFF Press/Hold to increase the desired light level.
15. WALL CONTROL OPERATING INSTRUCTIONS (cont.) NOTE: A maximum of 2 fans can operate on a circuit through the wall transmitter. A maximum of 12 fans can operate on a circuit through an on/off switch or breaker when utilizing the app for the fan control (without the wall transmitter in the circuit). Summer Mode (counter-clockwise) - A downward airflow creates a cooling effect as shown in Fig. 22. This allows you to set your air conditioner on a warmer setting without affecting your comfort.
16. APPLICATION In addition to the included wall control, you can control the fan through the Modern Forms app. 1. To use the app, download it for free from the App Store or Google Play. 2. Open the app to create your account. You can also log in with your FIGURE 24 FIGURE 25 Facebook or Google account. 3. Next, set up a WiFi connection. You’ll need the SSID and WiFi password for the network you want to connect to. 4.
17. TROUBLESHOOTING Problem Solution Fan will not start. 1. Check circuit fuses or breakers. 2. Check wall control LED indicator light. If LED is not illuminated when pushing a button, it is not transmitting a signal. Please check power to wall control and all electrical connections. 3. Assure that there are no more than 2 fans operating on a circuit through the wall control.
18.
PRODUCT DOWNROD FR- W1 8 1 5 MODEL DESCRIPTION FINISH XF-12 12 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-18 18 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-24 24 in downrod AS, CFI, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-36 36 in downrod XF-48 48 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-60 60 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT XF-72 72 in downrod AS, LN, SS BZ, DW, GB, GH, GW, MB, MW, OB, TT Al
Español For instructions in Spanish please visit the link below. Para obtener instrucciones en español, visite el siguiente enlace. www.modernforms.com/fan-instructions-espanol Français For instructions in French please visit the link below. Pour obtenir des instructions en français, veuillez visiter le lien ci-dessous. www.modernforms.
Get Smart The Modern Forms app synchronizes seamlessly with smart home devices you already own. To learn more go to modernforms.com/mfappins works with the Google Assistant Free App Download Sync with our exclusive Modern Forms App to control fan speed, use smart features like Adaptive Learning, create groups and reduce energy costs. modernforms.
FR- W1 8 1 5 27
FR-W1815 - 6 0 L ; FR- W 1 8 1 5 - 8 0 L modernforms.