VN385S01 Installation and Service Manual

1-550.26
4
Figure 4.3 - Horizontal Unit Delivery
Figure 4.3 Vertical Cone Jet
Figure 4.4 - Vertical One-Way & Two-Way Louvers
H
H
H
H
H
1.3
1.2
1.1
1.0
.9
.8
.7
.6
.5
Correction Factor "R"
150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 360 370
Average Water Temp – F
Steam Pressure
25 10 20 30 50 70 100
150
“Power-Throw” Vertical Type with Deflectors ➁
Horizontal Type ➀ Type ➁ No Deflector Cone-Jet Truncone Louvers
Model Height–Ft. Model Height–Ft. Model Height–Ft. Height–Ft. Height–Ft. Height–Ft.
No. Std. L.O.T. No. Std. L.O.T. No. Std. L.O.T. Std. L.O.T. Std. L.O.T. Std. L.O.T.
HSB/HC-18 8 9 — — — V/VN-42 ➁ 11 13 15 17 8 9 13 15
HSB/HC-24 9 11 — — — V/VN-59 ➁ 14 16 19 22 9 11 16 18
HSB/HC-33 10 12 — — — V/VN-78 ➁ 15 19 20 26 11 14 17 22
HSB/HC-47 12 14 — — — V/VN-95 ➁ 15 19 20 26 11 14 17 22
HSB/HC-63 14 16 — — — V/VN-139 ➁ 18 23 24 31 13 17 21 26
HSB/HC-86 15 17 — — — V/VN-161 ➁ 20 26 27 35 14 18 23 30
HSB/HC-108 17 19 — — — V/VN-193 ➁ 22 27 30 36 16 19 25 31
HSB/HC-121 16 18 — — — V/VN-212 ➁ 22 27 30 36 16 19 25 31
HSB/HC-165 19 21 — — — V/VN-247 ➁ 26 32 34 42 17 21 30 37
HSB/HC-193 18 — PT/PTN-279 ➁ 16 — V/VN-279 ➁ 30 36 37 45 18 22 35 41
HSB/HC-258 19 22 PT/PTN-333 ➁ 17 — V/VN-333 ➁ 30 36 37 45 17 20 35 41
HSB/HC-290 20 23 PT/PTN-385 ➁ 17 — V/VN-385 ➁ 30 36 36 43 17 20 35 41
HSB/HC-340 20 23 PT/PTN-500 ➁ 18 — V/VN-500 ➁ 37 45 44 54 19 24 42 51
— — — PT/PTN-610 ➁ 20 22 V/VN-610 ➁ 36 44 43 52 19 24 41 50
— — — PT-952 21 — V-952 ➁ 37 45 45 61 45 53 — —
➀ With horizontal louvers opened 30° from the vertical plane. HSB units have top and bottom piping connections, HC units have side connections. All have copper tubes.
➁ V and PT models have copper tubes, VN and PTN models have cupronickel tubes. Mounting heights are maximum for heaters operating at standard conditions
(2 lbs. steam or 220°F water with 60°F entering air). Heights listed for Louver or Cone-Jet are with deflectors in fully-opened position. Refer to Figure 4.2 for correction of
mounting heights under other operating conditions. Maximum mounting height will be reduced as entering air temperatures exceed 60°F.
These correction factors are to be used as multipliers to correct the maximum recommended mounting heights of unit heaters when operated with steam pressures other
than 2 pounds or with water at other than average temperature of 220°F.
Table 4.1 - Maximum Mounting Heights
UNIT MOUNTING
Figure 4.2 - Maximum Mounting Heights Correction Factors
H
Figure 4.6 - Vertical Truncone