Installation Guide

ManualsBrandsMoen ManualsShower Faucets82496EPBRB

E10

E11

English

Remove the lever (L) and

lever handle adapter (J).

Note the position of the stop.

Position the adjustable tem-

perature limit stop (D) so the

lever tops at that position. This

prevents the lever from being

turned into an unsafe

temperature.

5.3

Turn on the hot and

cold water supply to

check for leaks and set

temperature limit stop.

5.1

HOTTEST

120F

(49C)

Rotate the lever counterclockwise

until the water is to the maximum

desired temperature, not to exceed

120 degrees F (49 degrees C).

Seasonal maintenance of the

maximum outlet temperature

may be required due to changes in

groundwater temperature.

TURN LEVER TO THE

OFF POSITION ONCE THE

TEMPERATURE IS SET.

If temperature exceeds 120 degrees, go to step 5.3.

If temperature is less than 120 degrees, go to step 5.4.

5.2

Setting The Temperature Limit Stop and Finishing Your

Tub/Shower Installation

After setting the adjustable

temperature limit stop to the

desired position, remove the

lever (L), reattach the lever

handle adapter (J), adapter

screw (K), and lever (L) – make

sure ridges on back of (J) are

to the left of the tab on (D).

5.4

Using 7/64 inches hex wrench

(N), insert and tighten hex

screw (M) into lever (L).

5.5

Moen Lifetime Limited Warranty

Moen products have been manufactured under the highest standards of quality and workmanship.

Moen warrants to the original consumer purchaser for as long as the original consumer purchaser

owns their home (the “Warranty Period” for homeowners), that this faucet will be leak- and drip-free

during normal use and all parts and finishes of this faucet will be free from defects in material and

manufacturing workmanship. All other purchasers (including purchasers for industrial, commercial and

business use) are warranted for a period of 5 years from the original date of purchase (the “Warranty

Period” for non-homeowners).

If this faucet should ever develop a leak or drip during the Warranty Period, Moen will FREE OF

CHARGE provide the parts necessary to put the faucet back in good working condition and will

replace FREE OF CHARGE any part or finish that proves defective in material and manufacturing

workmanship, under normal installation, use and service. Replacement parts may be obtained by

calling 1-800-289-6636 (Canada 1-800-465-6130), or by writing to the address shown. Proof of

purchase (original sales receipt) from the original consumer purchaser must accompany all warranty

claims. Defects or damage caused by the use of other than genuine Moen parts is not covered by this

warranty. This warranty is applicable only to faucets purchased after December, 1995 and shall be

effective from the date of purchase as shown on purchaser’s receipt.

This warranty is extensive in that it covers replacement of all defective parts and finishes. However,

damage due to installation error, product abuse, product misuse, or use of cleaners containing

abrasives, alcohol or other organic solvents, whether performed by a contractor, service company, or

yourself, are excluded from this warranty. Moen will not be responsible for labor charges and/or

damage incurred in installation, repair or replacement, nor for any indirect, incidental or consequential

damages, losses, injury or costs of any nature relating to this faucet. Except as provided by law, this

warranty is in lieu of and excludes all other warranties, conditions and guarantees, whether expressed

or implied, statutory or otherwise, including without restriction those of merchantability or of fitness

for use.

Some states, provinces and nations do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitations or exclusions may not apply to you. This warranty

gives you specific legal rights and you may also have other rights which vary from state to state,

province to province, nation to nation. Moen will advise you of the procedure to follow in making

warranty claims. Simply write to Moen Incorporated using the address below. Explain the defect and

include proof of purchase and your name, address, area code and telephone number.

Moen Incorporated

25300 Al Moen Drive, North Olmsted, Ohio 44070-8022 U.S.A.

Attach the plastic

handle adapter (J)

to the cartridge

stem using the 1/2

inch adapter screw

(K). Make sure the

ridges on the back

of the adapter (J)

are to the left of the

tab on limit stop (D).

Place the lever (L) on

the lever handle

adapter.

4.5

Lever Handle Installation