Installation Guide

ManualsBrandsMOEN ManualsBathDarcy 8 in. Widespread 2-Handle High-Arc Bathroom Faucet with 4-Piece Bath Hardware Set in Mediterranean Bronze

Installation Guide

Guía de Instalación

Guide d’installation

HELPFUL TOOLS

For safety and ease of faucet replacement, Moen recommends

the use of these helpful tools.

HERRAMIENTAS ÚTILES

Para que el cambio de la llave sea fácil y seguro, Moen le

recomienda usar estas útiles herramientas.

OUTILS UTILES

Par mesure de sécurité et pour faciliter l’installation, Moen

suggère l’utilisation des outils suivants.

Please Contact Moen First

For Installation Help, Missing or Replacement Parts

(USA)

1-800-BUY-MOEN (1-800-289-6636)

Mon - Fri 8:00 AM to 7:00 PM, Eastern

Sat. 9:00 AM to 3:00 PM Eastern

WWW.MOEN.COM

(Canada)

1-800-465-6130

Mon - Fri 7:30 AM to 7:00 PM, Eastern

WWW.MOEN.CA

Por favor, contáctese primero con

Moen

Para obtener ayuda de instalación, piezas

faltantes o de recambio

01-800-718-4345

Lunes a viernes de 8:00 a 20:00 hs.

(Costa Este)

Sáb. 8:00 a 18:30 hs. (Costa Este)

WWW.MOEN.COM.MX

Veuillez d’abord contacter Moen

En cas de problèmes avec l’installation, ou

pour obtenir toute pièce manquante ou de

rechange

1-800-465-6130

Du lundi au vendredi :

de 7 h 30 à 19 h, HE

WWW.MOEN.CA

INS10391A - 2/15

TWO HANDLE LAVATORY FAUCET

MEZCLADORA PARA LAVABO

DE DOS MANERALES

ROBINET DE LAVABO À DEUX POIGNÉES

Images in this instruction sheet may not reect your current product, but should follow the same step-by-

step instructions.

Las imágenes en esta hoja de instrucciones pueden no reejar su producto pero se debe seguir las mismas

instrucciones de instalación paso a paso.

Il est possible que les images dans ce feuillet de directives ne reètent pas votre produit actuel, mais les

directives à suivre sont les mêmes.

Summary of content (12 pages)

PAGE 1
INS10391A - 2/15 Please Contact Moen First For Installation Help, Missing or Replacement Parts (USA) 1-800-BUY-MOEN (1-800-289-6636) Mon - Fri 8:00 AM to 7:00 PM, Eastern Sat. 9:00 AM to 3:00 PM Eastern WWW.MOEN.COM Installation Guide Guía de Instalación Guide d’installation (Canada) 1-800-465-6130 Mon - Fri 7:30 AM to 7:00 PM, Eastern WWW.MOEN.CA Por favor, contáctese primero con Moen Para obtener ayuda de instalación, piezas faltantes o de recambio 01-800-718-4345 Lunes a viernes de 8:00 a 20:00 hs.
PAGE 2
Parts List O M A. B. C. D. E. F. G. H. I. A x2 P B C x2 x2 F x2 J. K. L. M. N. O. P. Hose Lubricant Hot Valve Body Mounting Tool Hex Wrench Product ID Label Aerator Tool J. K. L. M. N. O. P. Manguera Lubricante Cuerpo de válvula caliente Herramienta de montaje Llave hexagonal Etiqueta de identificación del producto Herramienta del aireador J. K. L. M. N. O. P.
PAGE 3
INS10391A - 2/15 Parts List Waste Assembly Ensamblaje del desagüe Assemblage de la bonde R Q. R. S. T. U. V. W. Q Plug Lift Rod Pivot Rod Clip Waste Seat Drain Gasket Drain Washer Drain Nut X. Y. Z. AA. BB. CC. Drain O-Ring Pivot Rod Seat Tail Piece Pivot Rod Pivot Rod Nut Lift Rod Strap X. Y. Z. AA. BB. CC. Anillo de caucho del desagüe Asiento del pivote Sección final Pivote Tuerca del pivote Tirante de la barra de cierre vertical X. Y. Z. AA. BB. CC.
PAGE 4
1 2 B B H Place the spout assembly (B) into center opening in sink. From below the sink, slide the mounting bracket (H) onto the threaded shank (B). Coloque el conjunto del surtidor (B) en la abertura central del fregadero. Por debajo del fregadero, deslice la ménsula de montaje (H) sobre el tubo roscado (B). Placer l’assemblage du bec (B) dans l’ouverture centrale de l’évier. À partir du dessous de l’évier, faire glisser le support de montage (H) sur la tige filetée (B).
PAGE 5
INS10391A - 2/15 6 5 E D F D G Sealant Sellador Mastic Clip Groove Ranura del clip Rainure de l'étrier 1/2" L Apply a generous bead of plumbers putty or other sealant to underside of the upper mounting washers (D). A putty groove is provided for this purpose. Turn washers (D) over and position on sink as shown. Thread lower mounting nuts (F) onto the hot and cold valve bodies (L & G) far enough to allow the valve body clip groove to be 1/2" above the sink surface.
PAGE 6
8 7 C G Red = Hot Rojo = Caliente Rouge = Chaud B C Blue = Cold Azul = Frio Bleu = Froid L Push the hot valve body (L) on the left side up from below the sink. Use one hand to hold one valve body and the other hand to insert the clip (C) as shown in step 9. Repeat for valve body (G). Slide clip (C) into the groove on each valve body. Check to see that each valve body outlet connection below the deck points towards the spout shank (B) as shown.
PAGE 7
INS10391A - 2/15 11 12 L B G J Click Clic Cliquez sur G L Follow the same procedure as in step 11 to attach the hose (J) to the valve bodies (L & G). Listen for the “click” and tug to test engagement. Rotate the red stem extension on the hot valve body (L) clockwise and the blue stem extension on the cold valve body (G) counterclockwise until they stop. Siga el mismo procedimiento que en el paso 11 para conectar la manguera (J) a los cuerpos de válvula (L & G).
PAGE 8
14 15 W T T X Sealant Sellador Mastic correct orientation orientación correcta orientation correcte T W Z U V T Position the drain o-ring (X) in the groove at the top of the tail piece (Z) and thread onto the waste seat (T). After (Z) is attached to (T), rotate entire assembly so opening on (Z) points towards the wall. Now tighten drain nut (W). Remove excess sealant.
PAGE 9
INS10391A - 2/15 18 17 BB 2 1 Y B R 3 AA 19A 19B Q CC Q Install lift rod (R) into opening on the top of the spout (B). From under the sink, slide the lift rod strap (CC) onto pivot rod (R) and tighten the bolt finger tight. Final tightening will be completed during step 21. Verify white plastic pivot rod seat (Y) is in place with beveled side facing out. The pivot rod (AA) can be installed in two ways. Illustration (19A) shows the pivot rod (AA) next to hole in plug (Q).
PAGE 10
20 1. Loosen nut on liftrod strap (CC) to allow lift rod to rest in faucet. 2. Verify pivot rod (AA) is still pushed down, and plug (Q) is open in the sink. 3. Tighten bolt with wrench. 1. Afloje la tuerca en el tirante de la barra de cierre vertical (CC) para permitir que la barra de cierre vertical descanse sobre la mezcladora. 2. Verifique que el pivote (AA) todavía esté empujado hacia abajo, y que el tapón (Q) esté abierto en el fregadero. 3. Apriete el perno con una pinza. 2 1.
PAGE 11
INS10391A - 2/15 23 O 3 24 Cold Frio Froid 1 0 4 Hot Caliente Chaud 15 Sec. 45 30 P 5 2 Place product ID label (O) here. Coloque la etiqueta de identificación del producto (O) aquí. Placer l'étiquette d'identification du produit (O) ici. To flush debris from the plumbing system: 1. Remove the aerator by using the included aerator tool (P). Ensure aerator and aerator tool are engaged. Turn clockwise to loosen and remove aerator. 2. Turn faucet handles on and run hot and cold water for 15 seconds.
PAGE 12
Moen Limited Lifetime Warranty Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period" for homeowners), that this faucet will be leak- and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship.