Installation Guide

ManualsBrandsMOEN ManualsBathBanbury 8 in. Widespread 2-Handle Bathroom Faucet in Mediterranean Bronze (2-Pack)

INSXXX29 - 4/13

TWO HANDLE LAVATORY FAUCET

MEZCLADORA PARA LAVABO

DE DOS MANERALES

ROBINET DE LAVABO À DEUX POIGNÉES

Please Contact Moen First

For Installation Help, Missing or

Replacement Parts

(USA)

1-800-BUY-MOEN (1-800-289-6636)

Mon - Fri 8:00 AM to 8:00 PM, Eastern

Sat. 9:00 AM to 5:30 PM Eastern

WWW.MOEN.COM

(Canada)

1-800-465-6130

Mon - Fri 7:30 AM to 7:00 PM, Eastern

WWW.MOEN.CA

Por favor, contáctese primero

con Moen

Para obtener ayuda de instalación, piezas

faltantes o de recambio

01-800-718-4345

Lunes a viernes de 8:00 a 20:00 hs.

(Costa Este)

Sáb. 8:00 a 18:30 hs. (Costa Este)

WWW.MOEN.MX

Veuillez d’abord contacter Moen

en cas de problèmes avec l’installation, ou

pour obtenir toute pièce manquante ou de

rechange

1-800-465-6130

Du lundi au vendredi:

de 7 h 30 à 19 h, HE

WWW.MOEN.CA

INS2230 - 10/13

Installation Guide

Guía de Instalación

Guide d’installation

Images in this instruction sheet may not reect your current product, but should follow the same step-by-step instructions.

Las imágenes en esta hoja de instrucciones pueden no reejar su producto pero se debe seguir las mismas instrucciones de instalación paso a paso.

Il est possible que les images dans ce feuillet de directives ne reètent pas votre produit actuel, mais les directives à suivre sont les mêmes.

Summary of content (12 pages)

PAGE 1
INS2230 - 10/13 INSXXX29 - 4/13 Installation Guide Guía de Instalación Guide d’installation Please Contact Moen First For Installation Help, Missing or Replacement Parts (USA) 1-800-BUY-MOEN (1-800-289-6636) Mon - Fri 8:00 AM to 8:00 PM, Eastern Sat. 9:00 AM to 5:30 PM Eastern WWW.MOEN.COM (Canada) 1-800-465-6130 Mon - Fri 7:30 AM to 7:00 PM, Eastern www.moen.
PAGE 2
HELPFUL TOOLS For safety and ease of faucet replacement, Moen recommends the use of these helpful tools. CAUTION — TIPS FOR REMOVAL OF OLD FAUCET: Always turn water supply OFF before removing existing faucet or disassembling the valve. Open faucet handle to relieve water pressure and ensure that complete water shut-off has been accomplished. HERRAMIENTAS ÚTILES Para que el cambio de la llave sea fácil y seguro, Moen le recomienda usar estas útiles herramientas.
PAGE 3
INS2230 - 10/13 Parts List Q O E x2 A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Q. R. F x2 Lista de piezas A x2 R B C x2 D x2 G H I J K N P/ M N OE 99 N 91 5 P L M A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Q. R.
PAGE 4
Parts List Waste Assembly Ensamblaje del desagüe Assemblage de la bonde T S. Plug T. Lift Rod U. Pivot Rod Clip V. Waste Seat W. Drain Gasket X. Drain Washer Y. Drain Nut Z. Drain O-Ring AA. Pivot Rod Seat BB. Tail Piece CC. Pivot Rod DD. Pivot Rod Nut EE. Lift Rod Strap S U V W X Lista de piezas S. Tapón T. Barra de cierre vertical U. Clip del pivote V. Asiento del desagüe W. Empaque del desagüe X. Arandela del desagüe Y. Tuerca del desagüe Z. Anillo de caucho del desagüe AA. Asiento del pivote BB.
PAGE 5
INS2230 - 10/13 2 1 B Sealant Sellante Mastic B EN MO 9915 9 N / P M L Apply a small amount of silicone lubricant (M) to the black rubber o-ring on the spout shank (L) as shown. Apply a bead of plumbers putty or other sealant to the base of the spout (B) as shown. Turn spout upright. Aplique una pequeña cantidad de lubricante de silicona (M) al anillo de caucho negro en el tubo roscado del surtidor (L) como se muestra.
PAGE 6
5 H D D L O Sealant Sellante Mastic J O Use mounting tool (O) to tighten the mounting nut (J) to the spout base (L). Apply a generous bead of plumbers putty or other sealant to underside of the upper mounting washers (D). A putty groove is provided for this purpose. Turn washers (D) over and position on sink as shown. Utilice la herramienta de montaje (O) para apretar la tuerca de montaje (J) a la base de pico (L).
PAGE 7
INS2230 - 10/13 9 10 C F N F C G Slide clip (C) into the groove on each valve body. Check to see that each valve body outlet connection below the deck points towards the spout shank (L) as shown. Hold valve body (N) with one wrench and tighten the lower mounting nut (F) using a 2nd wrench. Repeat for valve body (G). Mantenga el cuerpo de la válvula (N) con una llave y apriete la tuerca de fijación inferior (F) con una llave de segunda. Repita el procedimiento para el cuerpo de la válvula (G).
PAGE 8
14 13 A G G A N N Rotate the red stem extension on the hot valve body (N) clockwise and the blue stem extension on the cold valve body (G) counterclockwise until they stop. Position (A) with handles pointing in the off direction as shown. Holding the handle stationary with one hand, thread the base of the handle assembly (A) onto the valve bodies (N&G) turning clockwise until (A) tightens to the deck.
PAGE 9
INS2230 - 10/13 16 17 Y V S Z correct orientation orientación correcta orientation correcte V BB Position the drain o-ring (Z) in the groove at the top of the tail piece (BB) and thread onto the waste seat (V). After (BB) is attached to (V), rotate entire assembly so opening on (BB) points towards the wall. Now tighten drain nut (Y). Remove excess sealant. Ubique el anillo de caucho del desagüe g (Z) en la ranura en la parte superior de la sección final (BB) y enrósquela en el asiento de desagüe (V).
PAGE 10
19 20 DD 2 1 AA 19A U CC 3 EE CC 1 1 19B S 2 S Push pivot rod (CC) down. Insert pivot rod through closest hole on liftrod strap (EE) with pivot rod down. Squeeze pivot rod clip (U) and slide other side of clip (U) onto the pivot rod (EE). Verify white plastic pivot rod seat (AA) is in place with beveled side facing out. The pivot rod (CC) can be installed in two ways. Illustration (19A) shows the pivot rod (CC) next to hole in plug (S).
PAGE 11
INS2230 - 10/13 22 23 2 B 3 1 2 1 T 1 Attach supply lines (not included) to shutoff faucet valve bodies. Attach supply lines (not included) to shutoff valves. Conecte las líneas de suministro (no incluidas) a los cuerpos de válvula de la mezcladora. Conecte las líneas de suministro (no incluidas)a las válvulas de cierre. Raccorder les conduites d’alimentation (non incluses) aux robinets d’arrêt. Raccorder les conduites d’alimentation (non incluses) aux corps de soupape du robinet d’arrêt.
PAGE 12
INS2230 - 10/13 Moen Limited Lifetime Warranty Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period” for homeowners), that this faucet will be leak- and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship.