Installation Guide

ManualsBrandsMoen ManualsBathroom Sink FaucetsOne-Handle Laboratory Faucet Chrome

Installation Guide

Guía de Instalación

Guide d’installation

HELPFUL TOOLS

For safety and ease of faucet

replacement, Moen recom-

mends the use of these helpful

tools.

HERRAMIENTAS ÚTILES

Para que el cambio de la llave

sea fácil y seguro, Moen le

recomienda usar estas útiles

herramientas.

OUTILS UTILES

Par mesure de sécurité et pour

faciliter l’installation, Moen

suggère l’utilisation des outils

suivants.

Please Contact Moen First

For Installation Help, Missing or Replacement Parts

(USA)

1-800-BUY-MOEN (1-800-289-6636)

Mon - Fri 8:00 AM to 7:00 PM, Eastern

Sat. 9:00 AM to 3:00 PM Eastern

WWW.MOEN.COM

(Canada)

1-800-465-6130

Mon - Fri 7:30 AM to 7:00 PM, Eastern

WWW.MOEN.CA

Por favor, contáctese primero con Moen

Para obtener ayuda de instalación, piezas

faltantes o de recambio

011 52 (800) 718-4345

Lunes a viernes de 8:00 a 20:00 hs.

(Costa Este)

Sáb. 8:00 a 18:30 hs. (Costa Este)

WWW.MOEN.COM.MX

Veuillez d’abord contacter Moen

En cas de problèmes avec l’installation, ou

pour obtenir toute pièce manquante ou de

rechange

1-800-465-6130

Du lundi au vendredi :

de 7 h 30 à 19 h, HE

WWW.MOEN.CA

INS10163D - 2/17

LAVATORY ELECTRONIC FAUCETS

8551AC- 8554AC

MEZCLADORAS ELECTRÓNICAS PARA LAVABO

8551AC- 8554AC

ROBINETS DE LAVABO ÉLECTRONIQUES

8551AC- 8554AC

1/4"

6.4 mm

18 AWG - Dual Strand

18 AWG -Doble hilo

AWG -Fil à deux brins

CAUTION — TIPS FOR REMOVAL OF OLD FAUCET:

Always turn water supply OFF before removing existing faucet or disassem-

bling the valve. Open faucet handle to relieve water pressure and ensure that

complete water shut-o has been accomplished.

PRECAUCIÓN — CONSEJOS PARA CAMBIAR LA LLAVE MEZCLADORA:

Siempre CIERRE la toma de agua antes de quitar la llave existente o desmontar

la válvula. Abra la llave para liberar la presión, y asegúrese de que esté bien

cerrada el agua.

ATTENTION  SUGGESTIONS POUR ENLEVER L’ANCIEN ROBINET:

Toujours couper l’alimentation en eau avant d’enlever ou de démonter le

robinet. Ouvrir le robinet pour libérer la pression d’eau et pour s’assurer que

l’alimentation en eau a bien été coupée.

8552AC Modern Style Mixing

8552AC Estilo moderno mezclador

8552AC Style moderne mélangeur

8553AC Transitional Style Non-Mixing

8553AC Estilo de transición no mezclador

8553AC Style transitionnel non mélangeur

Summary of content (12 pages)

PAGE 1
INS10163D - 2/17 Please Contact Moen First For Installation Help, Missing or Replacement Parts (USA) 1-800-BUY-MOEN (1-800-289-6636) Mon - Fri 8:00 AM to 7:00 PM, Eastern Sat. 9:00 AM to 3:00 PM Eastern WWW.MOEN.COM Installation Guide Guía de Instalación Guide d’installation (Canada) 1-800-465-6130 Mon - Fri 7:30 AM to 7:00 PM, Eastern WWW.MOEN.
PAGE 2
Parts List A. B. C. D. E. F. G. H. I. J. K. A S B C R D Q 1x or 2x A. B. C. D. E. F. G. H. I. J. K. F G O H N I Not included No incluida Pièce non comprise *M Liste des pièces K A. Clé Torx B. Trousse de bouton de bouchage (8552AC) C. Trousse de bouton de bouchage (8554AC) D. Assemblage de poignée E. Tige de montage F. Rondelle à ressort G. Écrou de montage H. Dispositif d'ancrage mural (2) I. Vis (2) J.
PAGE 3
INS10163D - 2/17 1 2 Q E 2 E F 1 P G *8552AC (mixing) is shown. 8551AC and 8553AC (non-mixing) will only have one supply hose. Lower the supply hoses (P) and mounting shank (E) through the hole in the deck until the outer shell (Q) is sitting on top of the deck. 1. From below the deck, slide the spring washer (F) then the mounting nut (G) onto the supply hoses. 2. Tighten mounting nut (G) to the top of mounting shank (E). Se muestra *8552AC (mezclador).
PAGE 4
5 Recommended Mounting Montaje recomendado Montage recommandé /8" 4-3mm) 0 (11 24" (61 cm) 24" (61 cm) 1/4" (6.4mm) O Ensure Control Box (J) is within reach when selecting mounting location. Note: Power Connection (O) is approximately 12" unless using Power Connection Extension (S) which extends length additional 18". Note: Ensure Control Box is mounted over Dual Strand 18 AWG Wire. Use 1/4" bit to drill hole locations. Distance is specified for Control Box mounting.
PAGE 5
INS10163D - 2/17 9 8 1 K I x2 A 2 Using a Torx Wrench (A), loosen Control Box Screw (K). Con una llave Torx (A), afloje el tornillo de la caja de control (K). À l’aide d’une clé Torx (A), dévisser la vis du boîtier de contrôle (K). 1. 2. Lift up and pull Control Box Cover away from remaining Control Box Housing and set aside for re-installation. Using a Phillips screwdriver, fully drive Screws (I). 1. 2.
PAGE 6
12 13 K 2 A J R 3 1 3 1. Re-attach cover of Control Box (J) to mounted portion to close. 2. Tighten Control Box Screw (K) into Control Box (J) with Torx Wrench (A). 3. Turn water on at the stops. Faucet Sensor (R) will begin flashing during its boot sequence. After the boot sequence, the faucet will be ready to use. If you choose to make changes to the sensor programming, you have 5 minutes to enter programming mode (see page 11). 1.
PAGE 7
INS10163D - 2/17 14 Test for waterflow. Pruebe el flujo de agua. Tester le débit de l’eau. Temperature Adjustment For 8552AC and 8554AC Only / Ajuste de la temperatura para 8552AC y 8554AC solamente / Ajustement de température pour 8552AC et 8554AC seulement A1 A2 D D To externally adjust temperature. To turn faucet on manually. Installation is complete. Para ajustar externamente la temperatura. Para abrir la llave manualmente. La instalación está completa.
PAGE 8
Low Flow / Flujo bajo / Faible débit B1 Low Flow/Flujo bajo/Faible débit If low flow, turn off water at stops before cleaning filter. Si el flujo es bajo, corte el agua en las llaves de paso antes de limpiar el filtro. Si le débit est faible, couper l’alimentation en eau aux robinets d’arrêt avant de nettoyer le filtre. B4 B2 B3 To remove in-line filter, unthread filter cap on the check valve with flathead screwdriver.
PAGE 9
INS10163D - 2/17 C2 C1 C3 2 A D 1 A Q Remove red/ blue plug button from Handle Assembly (D). Use Torx Wrench (A) to unscrew mixing handle. Retire el botón de presión rojo/azul del conjunto de la mezcladora (D). Use la llave torx (A) para destornillar el monomando mezclador. Enlever le bouton de bouchage rouge/bleu de l’assemblage de poignée (D). Utiliser une clé Torx (A) pour dévisser la poignée de mélangeur.
PAGE 10
To lock temperature For 8554AC Para bloquear la temperatura para 8554AC Pour bloquer la température du modèle 8554AC C6 C7 2 C 1 3 A Q For 8554AC: Place Plug Button (C) in outer shell hole. From the inside of the shell, use the plug button retainer piece to lock the plug button to the shell. Replace outer shell on Faucet Assembly (Q). Para 8554AC: Coloque el botón de presión (C) en el agujero en la carcasa exterior.
PAGE 11
INS10163D - 2/17 Sensor Programming Programación del sensor Programmation du détecteur Your faucet comes with programmable features: Sentinel Flow, Metering Mode, and Detection Distance. Visit pro.moen.com/sensor to watch videos on sensor programming. Su mezcladora viene con características programables: flujo centinela, modo de medición y distancia de detección. Visite pro.moen.com/ sensor para ver videos sobre programación del sensor.
PAGE 12
Moen Limited Lifetime Warranty Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period" for homeowners), that this faucet will be leak- and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship.