KITCHEN DECK FAUCETS INSTALLATION INSTRUCTIONS 7300, 8700

ManualsBrandsMoen ManualsIndoor Furnishing8700

7300, 8700 SERIES

INSTALLATION INSTRUCTIONS

THESE INSTRUCTIONS MUST BE

LEFT WITH HOMEOWNER

KITCHEN DECK FAUCETS

Single-Handle - for Eight-Inch Centers

MT170

CAUTION:

CLIP

EAR

Equipped with Flow-Rator® Aerator or Swing-N-Spray Aerator

Always turn water off before disassembling the valve. Open valve

handle to relieve water pressure and insure that complete water shut-

off has been accomplished.

Before turning water on during either rough-in or trim-out, make sure that cartridge retainer clip is in place. The

cartridge and retainer clip were properly installed and tested before leaving the factory. Although it is unlikely,

it is nevertheless possible that through the handling of the valve by any number of persons the retainer clip

may not be properly installed. This should be carefully checked at time of rough-in and trim-out. If the retainer

clip is not properly installed, water pressure could force the cartridge out of the casting. Personal injury or water

damage to the premises could result.

Complies with ASME A112.18.1M and CSA B125

Measurements

"FLOW-RATOR"

AERATOR

9" (229mm)

SPOUT

7-1/2" (191mm)

NOMINAL

OPEN POSITION

1/2" STRAIGHT

PIPE THREAD

MOUNTING

NUT/WASHER

TAILPIECE NUT

FOR 8" (203mm) CENTERS

5-3/8" (137mm)

NOMINAL

(9" SPOUT)

7-1/8" (181mm)

NOMINAL

(12" SPOUT)

DECK ESCUTCHEON

10" (254mm) X 2" (51mm) WIDE

(DECK GASKET IS ONLY

USED WITH DECORATOR MODELS)

2-1/8"

(54mm)

DECK

GASKET

Summary of content (4 pages)

PAGE 1
7300, 8700 SERIES MT170 ® INSTALLATION INSTRUCTIONS THESE INSTRUCTIONS MUST BE LEFT WITH HOMEOWNER KITCHEN DECK FAUCETS Single-Handle - for Eight-Inch Centers Measurements 9" (229mm) SPOUT "FLOW-RATOR" AERATOR 5-3/8" (137mm) NOMINAL (9" SPOUT) 7-1/2" (191mm) NOMINAL OPEN POSITION 7-1/8" (181mm) NOMINAL (12" SPOUT) 2-1/8" (54mm) 1/2" STRAIGHT PIPE THREAD DECK GASKET MOUNTING NUT/WASHER TAILPIECE NUT FOR 8" (203mm) CENTERS DECK ESCUTCHEON 10" (254mm) X 2" (51mm) WIDE (DECK GASKET IS ONLY USED WIT
PAGE 2
Installation TO INSTALL FAUCET: Be sure sink or mounting surface is clean and dry. Place deck gasket on bottom of faucet and insert faucet supplies down through deck holes. Center deck gasket and faucet on sink. Tighten mounting nuts from below deck. Carefully trim excess deck gasket. Make connections to your hot and cold water supplies. TO INSTALL HOSE AND SPRAY: Place a bead of plumber's putty under the rim of the spray escutcheon.
PAGE 3
Disassembly HANDLE COVER 1. Turn "OFF" both hot and cold water supplies. Turn faucet on to relieve pressure and insure complete shut off.. Pull handle cap up and off (it snaps into place). Remove the handle screw (illustration 1). 2. Push the cartridge stem down and then lift and tilt handle lever and handle body off. HANDLE ASSEMBLY HANDLE LEVER ILLUSTRATION 1 RETAINER PIVOT NUT CARTRIDGE EARS ➤ 3. Unscrew retainer pivot nut. HANDLE SCREW 4. Lift and twist spout off.
PAGE 4
Consumer Information Faucets made of leaded brass alloys may contribute small amounts of lead to water that is allowed to stand in contact with the brass. The amount of lead contributed by any faucet is highest when the faucet is new. The following steps may reduce potential exposure to lead from faucets and other parts of the plumbing system: • Always run the water for a few seconds prior to use for drinking or cooking. • Use only cold water for drinking or cooking.