S p e c i f i c a t i o n s DESCRIPTION • • • • • Various finishes identified by suffix Handheld shower 69" double interlock spiral hose (metal) Double check valve in handle 30" slide bar with push button height selection OPERATION • • Single function Handshower holder rotates to adjust angle of handshower FLOW • • EP17 suffix models designed to deliver 1.75 gpm (6.7 L/min) max EP suffix models designted to deliver 2.
INS1901G - 9/15 Installation Guide Guía de Instalación Guide d’installation Please Contact Moen First For Installation Help, Missing or Replacement Parts (USA) 1-800-BUY-MOEN (1-800-289-6636) Mon - Fri 8:00 AM to 7:00 PM, Eastern Sat. 9:00 AM to 3:00 PM Eastern WWW.MOEN.COM (Canada) 1-800-465-6130 Mon - Fri 7:30 AM to 7:00 PM, Eastern WWW.MOEN.CA T2191 T2192 T2193 Shower heads: Standard 9.5 L/min (2.5 gpm) max. and High Efficiency 7.6 L/min (2.0 gpm) max.
A* H * Included with valve Incluído con la mezcladora Inclus avec la soupape 2x I B J C K 5/32" O D L 7/64" P E M F N G Parts List Lista de piezas Liste des pièces A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P.
1 Option / Opción / Option 2 Option/Opción/Option Option / Opción / Option 1 1 3 H I 2 3 G 2" (51mm) MIN. 2-3/4" (70mm) MAX. 3 I Thread seal tape Cinta para sellar roscas Ruban pour joints filetés Thread seal tape Cinta para sellar roscas Ruban pour joints filetés J 2 5/32" 5/32" 5/32po Barely tighten screw. Apriete apenas el tornillo. Visser la vis sans trop serrer. O 2 1. Wrap thread seal tape around Shower Arm (I) threads. 2. Screw Shower Arm into connection in wall. 1.
INS1901G - 9/15 7 8 NO NON HC 1 C HC YES SI/OUI 9 1 2 K L K D 2 M Make sure cartridge stem is positioned with notch facing down. Insert Key Stop (C) & Adjustable Limit Stop (D) into Stop Tube. Asegúrese de que el vástago del cartucho esté colocado con la muesca hacia abajo. Inserte el tope de llave (C) & el tope ajustable de límite (D) en el tubo de cierre. S'assurer que la tige de cartouche est bien positionnée avec l'encoche orientée vers le bas.
INS1901G - 9/15 11 13 12 K 3 K M 1 M M 1 1 2 3 + L K 3 - 2 D L 4 K 4 N P 2 7/64" Hex Wrench Llave hexagonal de 7/64" Clé hexagonale de 7/64 po D 1. Remove the Lever (M). 2. Remove Lever Handle Adapter (K). Note the position on the stop. 3. Remove the Adjustable Temperature Limit Stop (D), rotate clockwise to reduce maximum water temperature. 4. Re-install the Adjustable Temperature Limit Stop (D), this prevents the Lever (M) from being turned to a hotter temperature. 1.
Moen Limited Lifetime Warranty Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period" for homeowners), that this faucet will be leak- and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship.
INS10041D - 4/15 Please Contact Moen First For Installation Help, Missing or Replacement Parts (USA) 1-800-BUY-MOEN (1-800-289-6636) Mon - Fri 8:00 AM to 7:00 PM, Eastern Sat. 9:00 AM to 3:00 PM Eastern WWW.MOEN.COM (Canada) 1-800-465-6130 Mon - Fri 7:30 AM to 7:00 PM, Eastern WWW.MOEN.
FOR SET SCREW HANDLE CONFIGURATION MODELS: TS23005,TS325, TS4172, TS5205, T4611, T4191, T4511 C FOLLOW STEPS 1, 2, 3, 4, 5A, 6A, 7A D x2 E F G I J K PARA CONFIGURACIÓN DE TORNILLOS DE FIJACIÓN MODELOS: TS23005,TS325, TS4172, TS5205, T4611, T4191, T4511 SIGA LOS PASOS 1, 2, 3, 4, 5A, 6A, 7A POUR LES MODÈLES AVEC POIGNÉE À VIS D'ARRÊT : TS23005, TS325, TS4172, TS5205, T4611, T4191, T4511 A B H SUIVRE LES ÉTAPES 1, 2, 3, 4, 5A, 6A ET 7A FOR HANDLE SCREW WITH ADAPTER CONFIGURATION MODELS: T4311 C
1 2 Wall/Pared/Mur < 1/4” (6mm) Wall/Pared/Mur < 1/4” (6mm) less than 1/4" (6mm) B A E C menos de 1/4" (6mm) inférieure à 1/4 po (6 mm) Wall/Pared/Mur > 1/4” (6mm) greater than 1/4" (6mm) E C greater than 1/4" (6mm) mayor de 1/4" (6mm) mayor de 1/4" (6mm) supérieure à 1/4 po (6 mm) supérieure à 1/4 po (6 mm) For thin wall and thick wall installation, slide Escutcheon (C) over Stop Tube (E). Stop Tube (E) should protrude some once Escutcheon (C) is in place.
INS10041D - 4/15 5A 6A For Set Screw Handle Configuration Models/para Configuración De Tornillos De Fijación Modelos/pour Les Modèles Avec Poignée À Vis D'arrêt For Set Screw Handle Configuration Models/para Configuración De Tornillos De Fijación Modelos/pour Les Modèles Avec Poignée À Vis D'arrêt C F E J 1 G G 2 H 3 Install Lever Handle (J) onto Handle Adapter (G). Instale el maneral de palanca (J) sobre el adaptador del maneral (G).
INS10041D - 4/15 5B 6B For Handle Screw With Adapter Configuration Models/ Para Configuración De Tornillo De Maneral Con Adaptador Modelos/ Pour Les Modèles Avec Vis De Poignée Et Adaptateur For Handle Screw With Adapter Configuration Models/ Para Configuración De Tornillo De Maneral Con Adaptador Modelos/ Pour Les Modèles Avec Vis De Poignée Et Adaptateur C J E F G G 3 2 1 L Install Spacer (F) onto Stop Tube (E). Install Handle Adapter (G) to Spacer (F) and onto cartridge stem.
5C For Handle Screw Without Adapter Configuration Models/ Para Configuración De Tornillo De Maneral Sin Adaptador Modelos/ Pour Les Modèles Avec Vis De Poignée, Mais Sans Adaptateur F 6C For Handle Screw Without Adapter Configuration Models/ Para Configuración De Tornillo De Maneral Sin Adaptador Modelos/ Pour Les Modèles Avec Vis De Poignée, Mais Sans Adaptateur J L M Moen Limited Lifetime Warranty Moen le otorga Garantía limitada de por vida Moen products have been manufactured under the highest
Specifications DESCRIPTION • Metal construction with various finishes identified by suffix WARRANTY • Lifetime warranty against material or manufacturing defects DROP ELL Models: A721 series Finished Wall Surface 1.85” (47mm) 1/2-14 NPT Pipe (Not Included) 1" (25mm) Minimum Diameter Hole 1/2-14 NPSM Thread 3/8” (10mm) Back View Side View CRITICAL DIMENSIONS (DO NOT SCALE) 2/12 FOR MORE INFORMATION CALL: 1-800-BUY-MOEN www.moen.
Specifications DESCRIPTION • • • Brass construction 1/2" CC, IPS, or PEX connections with 1/4 turn stops Pressure balancing, four port, cycle valve • Adjustable temperature limit stop to control maximum hot water temperature Pressure balancing mechanism maintain selected discharge temperature to ± 3°F OPERATION • CARTRIDGE • • • 1222 cartridge design Nonmetallic/nonferrous and stainless steel materials Accommodates back to back installations • Third party certified to meet CSA B125.1, ASME A112.18.
Specifications DESCRIPTION • Three function transfer valve - 2 discrete outputs & 1 shared mode OPERATION • 180˚ rotational control CARTRIDGE • 116719 cartridge STANDARDS • Third party certified to ASME A112.18.1/CSA B125.
