Installation Guide

ManualsBrandsMOEN ManualsBathBanbury 4-Piece Bath Hardware Set with 18 in. Towel Bar, Paper Holder, Towel Ring, and Robe Hook in Chrome

 Y2618BN – 18” Towel Bar

Brushed Nickel Finish

 Y2624BN – 24” Towel Bar

Brushed Nickel Finish

 Y2618BRB – 18” Towel Bar

Mediterranean Bronze Finish

 Y2624BRB – 24” Towel Bar

Mediterranean Bronze Finish

 Y2618CH – 18” Towel Bar

Chrome Finish

 Y2624CH – 24” Towel Bar

Chrome Finish

 Y2622BRB – 24” Double

Towel Bar

Mediterranean Bronze Finish

 Y2622CH – 24” Double Towel

Bar

Chrome Finish

25300 AL MOEN DR I VE  N OR TH OLMSTED , OH 44070

C OR POR ATE H EAD QU AR TER S: (800) 321 -8809  F AX: (800) 848-6636

I NTER NATI ON AL: (440) 962 -2000  F AX: (440) 962 -2726

C USTOMER SER VI C E (U SA): 800 -882-0116  F AX: (888) 379-2720

W WW . MOEN . COM

Copyright Creative Specialties International Literature # BA1442

Towel Bar post is die cast from

highest quality zinc alloy (Zamac).

Casting is plated Chrome, Brushed

Nickel or Mediterranean Bronze.

Towel Bar is aluminum for Brushed

Nickel and Chrome finishes and

stainless steel for Mediterranean

Bronze.

Cleaning Instructions:

1. Position the mounting template on the wall in the desired location.

2. Using a level, align the template and tape it to the wall.

3. Drill two 5/16” holes at each mounting plate location that

corresponds to your product.

4. We recommend using the horizontal holes for drywall installation.

5. Remove the template from the wall.

6. Fold ends of the plastic toggle together and insert into each hole

in the wall.

7. Lightly tap anchors until flush with the wall.

8. One at a time, insert plastic pin into each of the anchors and

lightly tap to activate anchor.

9. Remove pin and repeat on all anchors.

10. One at a time, place each mounting plate over anchors (notch

facing downward) and insert screws through plate into anchors.

11. Tighten screws.

12. Assemble the Towel Bar and posts.

13. While assembled, position each end post with setscrews facing

down and place over both mounting plates. Tighten the

setscrews.

Stock Number:______________________Towel Bar

By Creative Specialties

Materials:

Installation Instructions:

Stock Numbers:

Dimensions:

18” & 24” Towel Bars

Y2618 & Y2624

Banbury® Technical Specification

To preserve the fine finish of this product, clean only with a soft

damp cloth. Dry well. Do not use commercial or abrasive cleaners.

Summary of content (4 pages)

PAGE 1
Banbury® Technical Specification 18” & 24” Towel Bars Stock Numbers:  Y2618BN – 18” Towel Bar Brushed Nickel Finish  Y2624BN – 24” Towel Bar Brushed Nickel Finish  Y2618BRB – 18” Towel Bar Mediterranean Bronze Finish  Y2624BRB – 24” Towel Bar Mediterranean Bronze Finish  Y2618CH – 18” Towel Bar Chrome Finish  Y2624CH – 24” Towel Bar Chrome Finish Materials: Y2622BRB – 24” Double  Towel Bar post Towel Bar is die cast from highest quality zinc alloy (Zamac).
PAGE 2
Banbury® Technical Specification Robe Hook Stock Numbers:  Y2603BN – Robe Hook Brushed Nickel Finish  Y2603BRB – Robe Hook Mediterranean Bronze Finish  Y2603CH – Robe Hook Chrome Finish Materials: Robe Hook is die cast from highest quality zinc alloy (Zamac). Y2603 Dimensions: Installation Instructions: 1. Remove mounting plate from hardware pack. 2. Position the mounting plate on the wall at desired location with “UP” facing you. Mark hole locations. 3.
PAGE 3
Banbury® Technical Specification Pivoting Paper Holder Stock Numbers:  Y2608BN – Pivoting Paper Holder Brushed Nickel Finish  Y2608BRB – Pivoting Paper Holder Mediterranean Bronze Finish  Y2608CH – Pivoting Paper Holder Chrome Finish Materials: Pivoting Paper Holder post is die cast from highest quality zinc alloy (Zamac). Casting is plated Chrome, Brushed Nickel or Mediterranean Bronze. The Pivoting Paper Holder arm is stainless steel. Y2608 Dimensions: Installation Instructions: 1.
PAGE 4
Banbury® Technical Specification Towel Ring Stock Numbers:  Y2686BN – Towel Ring Brushed Nickel Finish  Y2686BRB – Towel Ring Mediterranean Bronze Finish  Y2686CH – Towel Ring Chrome Finish Materials: Towel Ring post is die cast from highest quality zinc alloy (Zamac). Casting is plated in Chrome, Brushed Nickel or Mediterranean Bronze. Towel ring is aluminum for Brushed Nickel and Chrome finishes and stainless steel for Mediterranean Bronze. Y2686 Dimensions: Installation Instructions: 1.