Full Product Manual

1 ¼” Grab Bar rods are formed from
(.040) type 304 stainless steel tubing.
 LR8716D1GBN – 16” Designer
Elegance Grab Bar w/ Grip Pads
Brushed Nickel Finish, 1 ¼” Bar,
Concealed Screw Mounting
 LR8724D1GBN – 24” Designer
Elegance Grab Bar w/ Grip Pads
Brushed Nickel Finish, 1 ¼” Bar,
Concealed Screw Mounting
 LR8716D1GCH – 16” Designer
Elegance Grab Bar w/ Grip Pads
Chrome Finish, 1 ¼” Bar,
Concealed Screw Mounting
 LR8724D1GCH – 24” Designer
Elegance Grab Bar w/ Grip Pads
Chrome Finish, 1 ¼” Bar,
Concealed Screw Mounting
 LR8716D1GOWB – 16” Designer
Elegance Grab Bar w/ Grip Pads
Old World Bronze Finish, 1 ¼” Bar,
Concealed Screw Mounting
 LR8724D1GOWB – 24” Designer
Elegance Grab Bar w/ Grip Pads
Old World Bronze Finish, 1 ¼” Bar,
Concealed Screw Mounting
1. Ple ase note that screws MUST be mounted into a wood stud for secure installation.
2. Slide the decorative cover awa y from the hub end to expose the SecureMount™
m ounting flange. Do not remove protective plastic from decorative cover until
indicated later in these instructions.
3. Locate the studs behind the wall by using a stud sensor or other stud locating
m ethod. Studs are usually 16 in. apart; locate the center of each stud.
4. Moving aside the decorative cover as needed, with a pencil, mark three of the
m ounting locations on each of the two grab bar flanges. Two m arks to be made
above the grab bar in the area indicated in the illustration below. The third m ark
to be m ade below the grab bar in the area indicated in the illustration below.
De cide whether you would like to position your grab bar horizontally, vertically or
at an angle, remembering that BOTH ends o f the grab bar MUST be positioned
over a wood stud.
5. Moving the decorative cover as far away from the marked slots as possible, drill a
hole into the m arks, through the slots (as shown in illustration). Position the drill
at a slight a ngle in order to get around the grab bar and decorative cover, making
sure to drill into the wood stud. If desired, apply silicone caulk to the back of th e
de corative cover to guard against water penetration.
6. To m ount the grab bar, reposition one end of the grab bar SecureMount™
m ounting flange over the m arked holes.
7. Thread a wa sher onto each screw. Using the screwdriver, screw the wood scre ws
with wa shers into the SecureMount™ mounting flange at one end of the grab bar.
Then screw the wood screws with washers into the mounting flange at the other
end of the grab bar.
8. Tighten the screws until secure.
9. Slide the decorative cover over the SecureMount™ m ounting flange, rotating to
find the correct fit before snapping into place.
10. Slide decorative covers over SecureMount™ mounting flanges.
Stock Number:_________________________Grab Bars
By Creative Specialties
Materials:
Installation Instructions:
Stock Numbers:
Dimensions:
Designer Elegance Grab Bar w/ Grip Pads
LR8700D1G
Home Care Technical Specification
25300 AL MOEN D R I VE  N OR TH OLMSTED , OH 44070
C OR POR ATE H EAD QU AR TER S: [phone]  F AX: [phone]
I N TER N ATI ON AL: [phone]  F AX: (440) 962 -2726
C U STOMER SER VI C E (U SA): 800 -882-0116  F AX: [phone]
W W W . MOEN . C OM
Copyright Creative Specialties International 2005 Literature #BA1669
16" Grab Bar 24" Grab Bar
A 16.00 24.00
B 19.15 27.15
C 3.15 3.15
D 2.80 2.80
E 1.50 1.50