Installation & Assembly

ManualsBrandsMoen ManualsBathroom Remodel & Bathroom FixturesCommercial Complete Shower System

Installation Guide

Guía de Instalación

Guide d’installation

HELPFUL TOOLS

For safety and ease of shower

replacement, Moen recom-

mends the use of these helpful

tools.

HERRAMIENTAS ÚTILES

Para que el cambio de la

regadera sea fácil y seguro,

Moen le recomienda usar estas

útiles herramientas

OUTILS UTILES

Par mesure de sécurité et pour

faciliter le remplacement du

système de douche, Moen

suggère l’utilisation des outils

suivants:

Please Contact Moen First

For Installation Help, Missing or Replacement Parts(USA)

1-800-BUY-MOEN (1-800-289-6636)

Mon - Fri 8:00 AM to 7:00 PM, Eastern

Sat. 9:00 AM to 3:00 PM Eastern

WWW.MOEN.COM

(Canada)

1-800-465-6130

Mon - Fri 7:30 AM to 7:00 PM, Eastern

WWW.MOEN.CA

Shower heads:

tandard 9.5 L/min (2.5 gpm) max. and High Eciency 7.6 L/min (2.0

gpm) max. or less

For use with automatic compensating valves rated at 5.7 L/min (1.5

gpm) or less

Automatic Compensating Valves:

Posi-Temp® and CFG®: For use with Showerheads rated at 5.7 L/min

(1.5 gpm) or higher

ExactTemp® and ioDigital™: For use with Showerheads rated at 9.5 L/

min (2.5 gpm) or higher

Moentrol®: For use with Showerheads rated at 4.9 L/min (1.3 gpm) or

higher

Por favor, contáctese primero con Moen

Para obtener ayuda de instalación, piezas faltantes o de recambio

01-800-718-4345

Lunes a viernes de 8:00 a 20:00 hs.

(Costa Este)

Sáb. 8:00 a 18:30 hs. (Costa Este)

WWW.MOEN.COM.MX

Roseta: estándar 9.5 L/min (2.5 gpm) máx. y alta eciencia 7.6 L/min

(2.0 gpm) máx. o menos

Para usarse con válvulas de compensación automática de 5.7 L/min

(1.5 gpm) o menos

Válvulas de compensación automática:

Posi-Temp® y CFG®: para usarse con rosetas de 5.7 L/min (1.5 gpm) o

más

ExactTemp® y ioDigital™: para usarse con rosetas de 9.5 L/min (2.5

gpm) o más

Moentrol®: para usarse con rosetas de 4.9 L/min (1.3 gpm) o más

Veuillez d’abord contacter Moen

en cas de problèmes avec l’installation, ou pour obtenir toute pièce

manquante ou de rechange

1-800-465-6130

Du lundi au vendredi :

de 7 h 30 à 19 h, HE

WWW.MOEN.CA

Pommes de douche :

Standards 2,5 gpm (9,5 L/min) max. ou à haute ecacité 2,0 gpm max.

(7,6 L/min) ou moins

À utiliser avec des soupapes de compensation automatiques dont le

débit nominal est de 5,7 L/min (1,5 gpm) ou moins

Soupapes de compensation automatique :

Posi-Temp® et CFG®: À utiliser avec des pommes de douche dont le

débit nominal est de 5,7 L/min (1,5 gpm) ou plus

ExactTemp® et ioDigital

: À utiliser avec des pommes de douche

dont le débit nominal est de 9,5 L/min (2,5 gpm) ou plus

Moentrol® : À utiliser avec des pommes de douche dont le débit

nominal est de 4,9 L/min (1,3 gpm) ou plus

INS10416 - 4/15

MODERN SUITE SHOWERING

Models T9343, T9342, T9346 series

SUITE DE REGADERA MODERNA

Modelos Series T9343, T9342, T9346

COLLECTION DE PRODUITS DE

DOUCHE MODERNE

Modèles T9343, T9342, T9346

For Valve / Para la terminación /

Pour soupape

Thread seal tape

Cinta para sellar roscas

Ruban pour joints ﬁletés

For Trim / Para la válvula / Pour garniture

Summary of content (20 pages)

PAGE 1
INS10416 - 4/15 Please Contact Moen First For Installation Help, Missing or Replacement Parts(USA) 1-800-BUY-MOEN (1-800-289-6636) Mon - Fri 8:00 AM to 7:00 PM, Eastern Sat. 9:00 AM to 3:00 PM Eastern WWW.MOEN.COM (Canada) 1-800-465-6130 Mon - Fri 7:30 AM to 7:00 PM, Eastern WWW.MOEN.CA Installation Guide Guía de Instalación Guide d’installation Shower heads: Standard 9.5 L/min (2.5 gpm) max. and High Efficiency 7.6 L/min (2.0 gpm) max. or less For use with automatic compensating valves rated at 5.
PAGE 2
If installing Tub/Shower Trim, go to Page 11 If installing POSI-Temp®Valve, go to Page 4 If installing Transfer Valve, go to Page 7 Si va a instalar una válvula POSI-Temp®, vaya a la página 4 Si va a instalar una válvula desviadora, vaya a la página 7 Pour l'installation de la soupape Posi-Temp®, aller à la page 4. Pour l'installation du robinet coupleur, aller à la page 7.
PAGE 3
INS10416 - 4/15 Parts List HH* A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Q. R. S. II Lista de piezas BB CC DD Y EE Z FF GG* AA A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Q. R. S. JJ CAUTION — TIPS FOR REMOVAL OF OLD FAUCET: Always turn water supply OFF before removing existing faucet or disassembling the valve. Open faucet handle to relieve water pressure and ensure that complete water shut-off has been accomplished. Plaster Ground Stop Tube Key Stop Adj. Temp.
PAGE 4
POSI-Temp® Valve Installation / Instalación de la válvula POSI-Temp® / Installation de la soupape Posi-Temp® Important If a tub spout is installed, the drop and lookout must be 1/2" copper or 1/2" IPS pipe with no restrictive fittings. IMPORTANTE Si se instala un surtidor para tina de Moen, la bajada y el niple a la vista deben ser de cobre de 1/2 pulgada (12,7 mm) o de tubería IPS de 1/2 pulgada (12,7 mm) sin herrajes restrictivos.
PAGE 5
INS10416 - 4/15 Moen has provided a plaster ground attached to the valve to be used as an installation and alignment guide. The plaster ground comes attached to the valve in the standard configuration from the factory. The plaster ground may be configured in different ways to accommodate various installation needs and maximize the aesthetic look of the valve in the shower. The plaster ground may be left in place until the trim is installed in order to protect the valve from possible construction damage.
PAGE 6
Special instructions for shallow wall cavity installations This plaster ground valve assembly variation should only be used when the wall cavity restricts the depth the valve may be placed in the wall. It can be used with either the thick wall installation when the back wall prevents the plaster ground printed face from coming flush to the finished wall or the thin wall installation where the plaster ground / valve assembly will not fit within the wall cavity.
PAGE 7
INS10416 - 4/15 Transfer Valve Installation / Instalación de la válvula desviadora / Installation du robinet coupleur B1 Finished Wall Pared Terminada Mur Fini 12" (305 mm) 1/2" (12,7 mm) 56" TYP (142 cm) Rough-in Body Casting a. The distance from the supply valve center to the center of the transfer valve must be a minimum of 12" (305mm) to assure proper clearance of the transfer valve escutcheon and supply valve escutcheon. b.
PAGE 8
Stem / Vástago / Tige Handle Stem Bushing / Manguito del vástago del monomando / Douille de tige de poignée Plaster Ground / Plantilla de yeso / Arrêt d'enduit Valve Housing / Bastidor de la válvula / Boîtier de soupape Cartridge / Cartucho / Cartouche Top Plate / Plancha superior / Cartouche de plaque supérieure Removing Cartridge for CC Connection/Servicing 1. Remove plaster ground but do not discard. 2.
PAGE 9
INS10416 - 4/15 B3 Installing Cartridge Into Transfer Valve Body (Right) 1. Place the cartridge into the transfer valve body, positioning the 2 locating pins on the bottom of the cartridge (Figure 1) into the 2 locating holes in the transfer valve body (Figure 2). Assure that the stem flats locating mark is facing upwards and away from the inlet (Figure 3). 2.
PAGE 10
B4 Continued 1. Prior to Escutcheon installation, verify that the plaster ground has been removed from the valve so that the trim will fit properly. 2. Screw on the Mounting Sleeve passing through the Escutcheon such that the outer rim of the sleeve presses up firmly against the Escutcheon, holding it in place against the wall.
PAGE 11
INS10416 - 4/15 Tub/Shower Trim Installation / Instalación de la terminación para tina/regadera / Installation de garniture de douche/baignoire C C1 IMPORTANT / IMPORTANTE / IMPORTANT Required for Installation Necesario para la instalación Requis pour l’installation 1 2 B 3 C D Ensure retainer clips are installed prior to escutcheon installation. Asegúrese de que los broches retenedores se hayan instalado antes de la instalación del chapetón.
PAGE 12
C4 C5 1 G H 3 3 I 2 5/32 Hex Llave Hexagonal Clé hexagonale 4 1 Thread seal tape Cinta para sellar roscas Ruban pour joints filetés 2 5/32 Hex Llave Hexagonal Clé hexagonale 1. Slide Shower Arm Flange (G) onto Shower Arm (H). 2. Wrap Shower Arm (H) with thread seal tape. 3. Thread Shower Head (I) onto Shower Arm. 1. Deslice la brida del brazo de la regadera (G) en el brazo de la regadera (H). 2. Envuelva el brazo de la regadera (H) con cinta de sellar roscas. 3.
PAGE 13
INS10416 - 4/15 C8 HC C9 NO NON 1 J K 2 3 HC YES SI/OUI 1. Place Handle Adapter (J) onto cartridge stem. 2. Place Handle (K) onto Handle Adapter (J). 3. Secure with Torx Screw (L). Make sure cartridge stem is positioned with notch facing down. Asegúrese de que el vástago del cartucho esté colocado con la muesca hacia abajo. S'assurer que la tige de cartouche est bien positionnée avec l'encoche orientée vers le bas. 1. Coloque el adaptador del monomando (J) sobre el vástago del cartucho. 2.
PAGE 14
C11 1. Remove the Torx Screw (L) and Handle (K). 2. Remove Lever Handle Adapter (J). Note the position on the stop. 3. Position the Adjustable Temperature Limit Stop (D) so the Lever stops at the position clockwise to lower temperature. 4. Re-insert Adjustable Temperature Limit Stop (D) This prevents the Lever from being turned into an unsafe temperature. K 1. Retire el tornillo torx (L) y el monomando (K). 2. Retire el adaptador del monomando de palanca (J). Note la posición en el tope. 3.
PAGE 15
INS10416 - 4/15 Slide Bar System Installation / Instalación del sistema de barra deslizante / Installation du système de barre coulissante D1 D2A 5/16" Hollow wall option Opción para pared hueca Option pour mur creux 5/8" 30 5/8" Wall Thickness Grosor de pared Épaisseur de paroi 1/2" (13mm) MIN. 1-1/2" (38mm) MAX. 30 5/8" 5/8" 5/16" For Hollow Wall Option: Measure distances, mark with a pencil, and drill a 5/8" hole into wall for slidebar installation.
PAGE 16
D4A D3 EE Hollow wall option Opción para pared hueca Option pour mur creux 1 GG* CC 2 CC HH* x2 BB BB For Hollow Wall Install Option: Thread Bracket Screw (HH) into Bracket (CC) and into Bracket Toggle (GG). Pinch ends of Toggle to fit into wall opening. Toggle should then expand. Para opción de instalación sobre pared hueca: Haga pasar el tornillo de la ménsula (HH) dentro de la ménsula (CC) y dentro de la articulación de la ménsula (GG).
PAGE 17
INS10416 - 4/15 D5A D5B Hollow wall option Opción para pared hueca Option pour mur creux Wood screw option Opción con tornillo para madera Option pour vis à bois 1 GG 2 CC go to vaya a aller à CC HH BB 6 go to vaya a aller à For Hollow Wall Option: Hold Bracket (CC) towards you and tighten Bracket Screws (HH) using a flat screwdriver. Go to Step 6. JJ BB 6 For Wood Screw Install Option: Finish securing Wood Screws (JJ) until Bracket (CC) is secured to wall. Go to Step 6.
PAGE 18
D8 D9 3 2 DD Z FF 1 AA AA 18 3
PAGE 19
INS10416 - 4/15 19
PAGE 20
Moen Limited Lifetime Warranty Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period" for homeowners), that this faucet will be leak- and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship.