Installation & Assembly

ManualsBrandsMoen ManualsCore PlumbingMosaic Multi Function Adjustable Shower Head

Installation Guide

Guía de Instalación

Guide d’installation

HELPFUL TOOLS

For safety and ease of faucet replacement, Moen recommends the use of these

helpful tools.

HERRAMIENTAS ÚTILES

Para que el cambio de la llave sea fácil y seguro, Moen le recomienda usar estas

útiles herramientas.

OUTILS UTILES

Par mesure de sécurité et pour faciliter l’installation, Moen suggère l’utilisation des

outils suivants.

Please Contact Moen First

For Installation Help, Missing or Replacement Parts

(USA)

1-800-BUY-MOEN (1-800-289-6636)

Mon - Fri 8:00 AM to 7:00 PM, Eastern

Sat. 9:00 AM to 3:00 PM Eastern

WWW.MOEN.COM

(Canada)

1-800-465-6130

Mon - Fri 7:30 AM to 7:00 PM, Eastern

WWW.MOEN.CA

Shower heads:

Standard 9.5 L/min (2.5 gpm) max. and High Eciency 7.6 L/min (2.0

gpm) max. or less

For use with automatic compensating valves rated at 4.2 L/min (1.1

gpm) or less

Por favor, contáctese primero con Moen

Para obtener ayuda de instalación, piezas faltantes o de recambio

01-800-718-4345

Lunes a viernes de 8:00 a 20:00 hs.

(Costa Este)

Sáb. 8:00 a 18:30 hs. (Costa Este)

WWW.MOEN.COM.MX

Roseta:

Estándar 9.5 L/min (2.5 gpm) máx. y alta eciencia 7.6 L/min (2.0

gpm) máx. o menos

Para usarse con válvulas de compensación automática de 4.2 L/min

(1.1 gpm) o menos

Veuillez d’abord contacter Moen

En cas de problèmes avec l’installation, ou pour obtenir toute

pièce manquante ou de rechange

1-800-465-6130

Du lundi au vendredi :

de 7 h 30 à 19 h, HE

WWW.MOEN.CA

Pommes de douche :

Standards 9,5 L/min (2,5 gpm) max. ou à haute ecacité 7,6 L/min

(2,0 gpm)

À utiliser avec des soupapes de compensation automatiques dont le

débit nominal est de 4,2 L/min (1,1 gpm) ou moins

INS10372A - 8/15

MOSAIC™ FLUSH MOUNT BODY SPRAY

TRIM AND ROUGHIN

Note: Style varies by model

ACABADO Y EMPOTRADO DEL ROCIADOR

CORPORAL MOSAIC™ DE MONTAJE A RAS

Nota: El estilo varía por el modelo.

PLOMBERIE BRUTE ET GARNITURE DE JET

CORPOREL ENCASTRÉE MOSAIC

Remarque : le style varie selon le modèle

S1300

TS1420TS1422

CAUTION — TIPS FOR REMOVAL OF OLD FAUCET:

Always turn water supply OFF before removing existing faucet or disassembling the valve.

Open faucet handle to relieve water pressure and ensure that complete water shut-o has

been accomplished.

PRECAUCIÓN — CONSEJOS PARA CAMBIAR LA LLAVE MEZCLADORA:

Siempre CIERRE la toma de agua antes de quitar la llave existente o desmontar la válvula.

Abra la llave para liberar la presión, y asegúrese de que esté bien cerrada el agua.

ATTENTION  SUGGESTIONS POUR ENLEVER L’ANCIEN ROBINET:

Toujours couper l’alimentation en eau avant d’enlever ou de démonter le robinet. Ouvrir le robinet

pour libérer la pression d’eau et pour s’assurer que l’alimentation en eau a bien été coupée.

Summary of content (8 pages)

PAGE 1
INS10372A - 8/15 Please Contact Moen First For Installation Help, Missing or Replacement Parts (USA) 1-800-BUY-MOEN (1-800-289-6636) Mon - Fri 8:00 AM to 7:00 PM, Eastern Sat. 9:00 AM to 3:00 PM Eastern WWW.MOEN.COM (Canada) 1-800-465-6130 Mon - Fri 7:30 AM to 7:00 PM, Eastern WWW.MOEN.CA Installation Guide Guía de Instalación Guide d’installation Shower heads: Standard 9.5 L/min (2.5 gpm) max. and High Efficiency 7.6 L/min (2.0 gpm) max. or less For use with automatic compensating valves rated at 4.
PAGE 2
Rough-In / Empotrado / Plomberie brute 8-1/2” (216 mm) Rough-In Mounting Dimensions Dimensiones de montaje del empotrado Dimensions du montage de la plomberie brute 3-1/4" ± 3/8" (82mm ±10mm) connector to finished wall D 8,25 cm ± 0,95 cm (82mm ±10mm) conector a la pared acabada 4-1/2” (114 mm) Dia.
PAGE 3
INS10372A - 8/15 ROUGH-IN INSTALLATION / INSTALACIÓN DEL EMPOTRADO / INSTALLATION DE LA PLOMBERIE BRUTE 1 3 2 2-1/2” ± 3/8” Bracket to Finish Wall (63mm ± 10mm) D 6,35 cm ± 0,95 cm de la ménsula a la pared acabada D Du support au mur fini 63 mm ± 10 mm (1 1/2 po ± 3/8 po) D C x4 A Must Use All 4 Screws Deben utilizarse los 4 tornillos Les quatre (4) vis doivent être utilisées Measure 2-1/2" ± 3/8" from finished wall and mark with pencil 4 spots in Bracket (D) screw holes.
PAGE 4
6 8 7 A A 1 2 F G E Attach Plaster Guard (E) onto Connector (A) as shown. Insert Test Plug (F) into Connector (A). 1. Conecte el protector de yeso (E) al conector (A) como se muestra. Inserte el tapón de prueba (F) en el conector (A). 2. Insérer le bouchon d'essai (F) dans le raccord (A). 1. Fixer le protecteur de plâtre (E) dans le raccord (A), comme illustré. 2. 1. 2. Install Test Plug Nut (G) over Test Plug (F) and onto Connector. Tighten Nut with an adjustable wrench.
PAGE 5
INS10372A - 8/15 11 13 12 A A E I Carefully remove Plaster Guard (E) from Connector (A). Retire cuidadosamente el protector de yeso (E) del conector (A). Enlever soigneusement le protecteur de plâtre (E) du raccord (A). If distance is less than or equal to 2-1/8" (54mm), proceed to step 13. If distance is greater than 2-1/8", order 1" extension kit #155656. Si la distancia es inferior o igual a 5,40 cm (54mm), proceda al paso 13.
PAGE 6
16 1. Orient spray face with recess at bottom as shown. Rotate tab clockwise till it stops. 2. Install Spray Assembly (K) into opening of Housing (I). Ensure 3 hex screw holes are aligned. Use 9/64" Hex Wrench (P) to tighten hex screws to Housing (I). I 1. Oriente la cara del rociador con el hueco en la parte inferior como se ilustra. Haga girar la aleta en dirección de las agujas del reloj hasta que se detenga. 2. Instale el conjunto del rociador (K) en la abertura de la caja (I).
PAGE 7
INS10372A - 8/15 Square Trim Only 19 Acabado cuadrado solamente A Garniture carrée seulement Reduced Flow Turn off water supply. M 1 Flujo Irregular Apague el suministro de agua. Débit réduit Couper l'alimentation en eau. 1 O N 2 Q 1. Rotate Trim Ring-Round (N) counter clockwise. 2. Remove Trim Ring-Round (N) and set aside for re-install. 1. Install Set Screw (O) into Trim Ring-Square (M). 2. Tighten Set Screw (O) with 1/16" Hex Wrench (Q). Installation is complete. 1.
PAGE 8
Moen Limited Lifetime Warranty Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period" for homeowners), that this faucet will be leak- and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship.