Installation Guide

ManualsBrandsMOEN ManualsBathVia Single Hole Single-Handle Bathroom Faucet in Chrome

ONE-HANDLE LAVATORY FAUCET

MEZCLADORA MONOMANDO

PARA LAVABO

ROBINET DE LAVABO À UNE POIGNÉE

Please Contact Moen First

For Installation Help, Missing or

Replacement Parts

(USA)

1-800-BUY-MOEN (1-800-289-6636)

Mon - Fri 8:00 AM to 7:00 PM, Eastern

Sat. 9:00 AM to 3:00 PM Eastern

WWW.MOEN.COM

(Canada)

1-800-465-6130

Mon - Fri 7:30 AM to 7:00 PM, Eastern

WWW.MOEN.CA

Por favor, contáctese primero

con Moen

Para obtener ayuda de instalación, piezas

faltantes o de recambio

01-800-718-4345

Lunes a viernes de 8:00 a 20:00 hs.

(Costa Este)

Sáb. 8:00 a 18:30 hs. (Costa Este)

WWW.MOEN.COM.MX

Veuillez d’abord contacter Moen

En cas de problèmes avec l’installation, ou

pour obtenir toute pièce manquante ou

de rechange

1-800-465-6130

Du lundi au vendredi :

de 7 h 30 à 19 h, HE

WWW.MOEN.CA

INS10457 - 9/15

Installation Guide

Guía de instalación

Guide d’installation

HELPFUL TOOLS

For safety and ease of faucet replacement, Moen

recommends the use of these helpful tools.

HERRAMIENTAS ÚTILES

Para que el cambio de la llave sea fácil y

seguro, Moen le recomienda usar estas útiles

herramientas.

OUTILS UTILES

Par mesure de sécurité et pour faciliter

l’installation, Moen suggère l’utilisation des

outils suivants.

Thread seal tape

Cinta para sellar roscas

Ruban pour joints letés

Sealant

Sellador

Mastic

S8000

CAUTION — TIPS FOR REMOVAL OF OLD FAUCET:

Always turn water supply OFF before removing existing faucet or

disassembling the valve. Open faucet handle to relieve water pressure

and ensure that complete water shut-o has been accomplished.

PRECAUCIÓN — CONSEJOS PARA CAMBIAR LA LLAVE

MEZCLADORA: Siempre CIERRE la toma de agua antes de quitar la

llave existente o desmontar la válvula. Abra la llave para liberar la

presión, y asegúrese de que esté bien cerrada el agua.

ATTENTION  SUGGESTIONS POUR ENLEVER L’ANCIEN

ROBINET: Toujours couper l’alimentation en eau avant d’enlever ou de

démonter le robinet. Ouvrir le robinet pour libérer la pression d’eau et

pour s’assurer que l’alimentation en eau a bien été coupée.

Above sink

Encima del lavabo

Au-dessus de l'évier

Below sink

Debajo del fregadero

Sous l'évier

Icon Legend/Leyenda de Iconos/

Légende des icônes

S8001

Summary of content (8 pages)

PAGE 1
INS10457 - 9/15 Please Contact Moen First For Installation Help, Missing or Replacement Parts (USA) 1-800-BUY-MOEN (1-800-289-6636) Mon - Fri 8:00 AM to 7:00 PM, Eastern Sat. 9:00 AM to 3:00 PM Eastern WWW.MOEN.COM (Canada) 1-800-465-6130 Mon - Fri 7:30 AM to 7:00 PM, Eastern WWW.MOEN.
PAGE 2
Model Modelo Modèle S8001 F A G Model Modelo Modèle S8000 T Model Modelo Modèle S8000 G H I J B K L M N O C D P E Q R S Parts List Lista de piezas Liste des pièces A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Q. R. S. T. A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Q. R. S. T. A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Q. R. S. T.
PAGE 3
INS10457 - 9/15 2 1 Model Modelo Modèle S8000 A Model Modelo Modèle S8001 A G G G T T 1 C 2 Install Deck Gasket (C) onto Faucet Body (A). 1. Assemble Lift Rod (G) and Lower Lift Rod (T) together. 2. Insert Lift Rod (G ) into back of Faucet Body (A). Instale el empaque de cubierta (C) sobre el cuerpo de la mezcladora (A). 1. Arme la barra de cierre vertical (G) t la barra de cierre vertical inferior (T) juntas. 2.
PAGE 4
5 6 <1" (25mm) For Deck Thickness less than 1" Para grosor de cubierta menor de 1" Pour épaisseur de plateforme inférieure à 25 mm Option/Opción/Option E 1 3 >1" (25mm) E F F 2 For Deck Thickness more than 1" Para grosor de cubierta mayor de 1" 1. Slide Installation Tool (F) onto Mounting Nut (E). 2. Insert screwdriver into Installation Tool. 3. Tighten. Pour épaisseur de plateforme supérieure à 25 mm Orient Mounting Nut (E) depending on deck thickness. See image on right for orientation.
PAGE 5
INS10457 - 9/15 9 10 Thread seal tape Cinta para sellar roscas Ruban pour joints filetés O N S O I 1 NO NO NON YES SÍ OUI 2 Make final tightening of Drain Nut (N) to Drain Body (O) with wrench. Ensure Pivot Rod opening on Drain Body points towards the wall. 1. Apply thread seal tape to threads of Tail Piece (S). Assemble to Drain Body (O). 2. Insert Waste Plug (I) into sink opening. Haga el ajuste final de la tuerca del desagüe (N) al cuerpo del desagüe (O) con una llave.
PAGE 6
12 Verify white plastic Pivot Rod Seat (P) is in place with beveled side facing out. The Pivot Rod (R) can be installed in two ways. Circle illustration shows the Pivot Rod (R) next to hole in Waste Plug (I). This allows the Waste Plug (I) to be pulled out for cleaning. Box illustration shows the Pivot Rod (R) inserted into the hole in the Waste Plug (I). This prevents the Waste Plug (I) from being easily removed after installation.
PAGE 7
INS10457 - 9/15 15 Tag Etiqueta Étiquette 1 Hot Caliente Chaud 3 2 (9.5 mm) (9,5 mm) Cold Frio Froid Optional/Opcional/Optionnel 1. Attach supply lines from faucet to shut off stops. 2. Use a wrench to tighten supplies. 3. Turn on water. Check for leaks. 1. Conecte las líneas de suministro de la mezcladora a los topes de cierre. 2. Use una llave para apretar las líneas de suministro. 3. Abra el agua. Verifique si hay pérdidas. 1.
PAGE 8
Moen Limited Lifetime Warranty Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period" for homeowners), that this faucet will be leak- and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship.