Installation Instructions

ManualsBrandsMoen ManualsBathHensley® Two-Handle 8" Widespread Bathroom Faucet in Mediterranean Bronze

INS10451C - 10/18

TWO HANDLE LAVATORY FAUCET

MEZCLADORA PARA LAVABO

DE DOS MANERALES

ROBINET DE LAVABO À DEUX POIGNÉES

Images in this instruction sheet may not reect your current product, but should follow the same

step-by-step instructions.

Las imágenes en esta hoja de instrucciones pueden no reejar su producto pero se debe seguir las mismas

instrucciones de instalación paso a paso.

Il est possible que les images dans ce feuillet de directives ne reètent pas votre produit actuel, mais les

directives à suivre sont les mêmes.

Please Contact Moen First

For Installation Help, Missing or

Replacement Parts

(USA)

1-800-BUY-MOEN (1-800-289-6636)

WWW.MOEN.COM

(Canada)

1-800-465-6130

WWW.MOEN.CA

Por favor, contáctese primero con Moen

Para obtener ayuda de instalación, piezas

faltantes o de recambio

011 52 (800) 718-4345

WWW.MOEN.COM.MX

Veuillez d’abord contacter Moen

En cas de problèmes avec l’installation, ou pour

obtenir toute pièce manquante ou de rechange

1-800-465-6130

WWW.MOEN.CA

CAUTION — TIPS FOR REMOVAL OF OLD FAUCET:

Always turn water supply OFF before removing existing faucet or disassembling the valve. Open

faucet handle to relieve water pressure and ensure that complete water shut-o has been

accomplished.

PRECAUCIÓN — CONSEJOS PARA CAMBIAR LA LLAVE MEZCLADORA:

Siempre CIERRE la toma de agua antes de quitar la llave existente o desmontar la válvula. Abra la

llave para liberar la presión, y asegúrese de que esté bien cerrada el agua.

ATTENTION  SUGGESTIONS POUR ENLEVER L’ANCIEN ROBINET:

Toujours couper l’alimentation en eau avant d’enlever ou de démonter le robinet. Ouvrir le robinet

pour libérer la pression d’eau et pour s’assurer que l’alimentation en eau a bien été coupée.

Icon Legend/Leyenda de Iconos/

Légende des icônes

Above sink

Encima del lavabo

Au-dessus de l’évier

Below sink

Debajo del fregadero

Sous l'évier

Regístrese en línea:

S’enregistrer en ligne :

www.moen.com/product-registration

Record Purchased Model Number:

Registro del número de modelo comprado:

Consigner ici le numéro du modèle acheté :

(Save instruction sheet for future reference)

(Guarde la hoja de instrucciones para futura refe-rencia)

(Garder ces directives pour référence ultérieure)

Image is for reference only

(Style varies by model)

La imagen es sólo como referencia

(El estilo varía por el modelo)

Cette image est fournie à titre iinformatif seulement

(Le style varie selon le modèle)

HELPFUL TOOLS

For safety and ease of

faucet replacement,

Moen recommends the

use of these helpful tools.

HERRAMIENTAS ÚTILES

Para que el cambio de la

llave sea fácil y seguro,

Moen le recomienda usar

estas útiles herramientas.

OUTILS UTILES

Par mesure de sécurité et

pour faciliter l’installation,

Moen suggère l’utilisation

des outils suivants.

Sealant

Sellador

Mastic

Sealant

Sellador

Mastic

Summary of content (12 pages)

PAGE 1
INS10451C - 10/18 TWO HANDLE LAVATORY FAUCET MEZCLADORA PARA LAVABO DE DOS MANERALES ROBINET DE LAVABO À DEUX POIGNÉES Please Contact Moen First For Installation Help, Missing or Replacement Parts (USA) 1-800-BUY-MOEN (1-800-289-6636) WWW.MOEN.COM (Canada) 1-800-465-6130 WWW.MOEN.CA Images in this instruction sheet may not reflect your current product, but should follow the same step-by-step instructions.
PAGE 2
Parts List A. B. C. D. E. F. G. H. H A B C E I. J. K. L. M. N. O. Aerator Tool Waterway Cap Mounting Bracket Mounting Nut Cold Valve Body Hose Mounting Tool I. J. K. L. M. N. O. Herramienta del aireador Tapa del canal Ménsula de montaje Tuerca de montaje Cuerpo de válvula fría Manguera Herramienta de montaje I. J. K. L. M. N. O. Outil pour aérateur Capuchon pour conduite d’eau Support de montage Écrou de montage Corps de soupape d’eau froide Tuyau Outil de montage I Lista de piezas J A. B. C. D.
PAGE 3
INS10451C - 10/18 Parts List P. Q. R. S. T. U. V. P Plug Lift Rod Waste Seat Lift Rod Strap Drain Body Drain Gasket Drain Nut W. X. Y. Z.* Pivot Rod Pivot Rod Nut Pivot Rod Clip Supply Lines (x2) * Not included W. X. Y. Z.* Pivote Clip del pivote Tuerca del pivote Líneas de suministro (x2) * No incluidas W. X. Y. Z.* Tige de pivotement Bride de tige de pivotement Écrou de tige de pivotement Conduites d’alimentation (2) * Non incluses Q Lista de piezas R P. Q. R. S. T. U. V.
PAGE 4
1 2 H H J 2 K 1 1. Remove Waterway Cap (J). 2. Place the Spout Assembly (H) into center opening in sink. From below the sink, slide the Mounting Bracket (K) onto the threaded shank of Spout (H). 1. Retire la tapa del canal (J). 2. Coloque el conjunto del surtidor (H) en la abertura central del fregadero. À partir du dessous de l’évier, faire glisser le support de montage (K) sur la tige filetée du bec (H).
PAGE 5
INS10451C - 10/18 6 5 D C E C M Sealant Sellador Mastic Clip Groove Ranura del clip Rainure de l'étrier Apply a generous bead of sealant to underside of the upper mounting washers (C). A sealant groove is provided for this purpose. Turn washers (C) over and position on sink as shown. 1/2" F Thread Lower Mounting Nuts (E) onto the Hot and Cold Valve Bodies (F & M) far enough to allow the valve body clip groove to be 1/2" above the sink surface.
PAGE 6
8 9 B E E F H B L Slide Clip (B) into the groove on each Valve Body. Check to see that each Valve Body outlet connection below the deck points towards the Spout Shank (H) as shown. Hold Valve Body (F) with one wrench and tighten the Lower Mounting Nut (E) using a 2nd wrench. Repeat for Valve Body (L). Deslice el clip (B) dentro de la ranura en cada cuerpo de válvula.
PAGE 7
INS10451C - 10/18 13 12 A L L A F F Rotate the red stem extension on the Hot Valve Body (F) clockwise and the blue stem extension on the Cold Valve Body (L) counterclockwise until they stop. Position (A) with Handles pointing in the off direction as shown. Holding the Handle stationary with one hand, thread the base of the Handle Assembly (A) onto the Valve Bodies (F & L) turning clockwise until (A) tightens to the deck.
PAGE 8
16 17 R Q S T From the underside of the sink, thread the drain body (T) into the waste seat (R). Install lift rod (Q) into opening on the top of the faucet. Slide the lift rod strap (S) onto lift rod and tighten the bolt finger tight. Final tightening will be completed during Step 22. Desde la parte inferior del fregadero, enrosque el cuerpo de desagüe (T) en el asiento del desagüe (R). Instale la barra de cierre vertical (Q) en la abertura en la parte superior de la mezcladora.
PAGE 9
INS10451C - 10/18 20 The pivot rod (W) can be installed in two ways. Illustration (20A) shows the pivot rod (W) next to hole in plug (P). This allows the plug (P) to be pulled out for cleaning. Illustration (20B) shows the pivot rod (W) inserted into the hole in the plug (P). This prevents the plug (P) from being easily removed after installation. Once the pivot rod is installed (20A or 20B), tighten the pivot rod nut (Y). 1 2 W El pivote (W) puede ser instalado de dos formas.
PAGE 10
24 23 * Not included No incluidas Non incluses 2 x2 Z* M 1 F 3 1 * Not included No incluidas Non incluses 1 Z* x2 1. Attach Supply Lines (Z)* to each valve body (F & M). 2. Tighten by hand. 3. Tighten with an adjustable wrench. 1. Attach Supply Lines (Z)* to shutoff valves. 2. Tighten with wrench until secure. 1. Conecte las líneas de suministro (Z)* a las válvulas de cierre. 2. Apriete con una pinza hasta que queden firmes. 1.
PAGE 11
INS10451C - 10/18 TO FLUSH DEBRIS FROM THE PLUMBING SYSTEM / PARA ENJUAGAR LAS BASURAS DEL SISTEMA DE CAÑERÍAS / POUR ÉVACUER LES DÉBRIS DE LA PLOMBERIE A B I 0 2 15 Sec. 45 30 1. Remove the aerator by using the included aerator tool (I). Ensure aerator and aerator tool are engaged. 2. Turn clockwise to loosen and remove aerator. Turn faucet handles on and run hot and cold water for 15 seconds. Abra los manerales de la mezcladora y haga correr el agua fría y caliente durante 15 segundos.
PAGE 12
Moen Limited Lifetime Warranty Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period" for homeowners), that this faucet will be leak- and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship.