Specifications
Flara
®
Technical Specication
YG0312/YG0318/YG0312/YG0324/YG0336/YG0342
Grab Bar
Stock Numbers:
Materials:
Dimensions:
Installation Instructions:
Cleaning Instructions:
☐ YG0312CH – 12” Grab Bar
Chrome Finish
☐ YG0318CH – 18” Grab Bar
Chrome Finish
☐ YG0324CH – 24” Grab Bar
Chrome Finish
☐ YG0336CH – 36” Grab Bar
Chrome Finish
☐ YG0342CH – 42” Grab Bar
Chrome Finish
☐ YG0312BN – 12” Grab Bar
Brushed Nickel Finish
☐ YG0318BN – 18” Grab Bar
Brushed Nickel Finish
☐ YG0324BN – 24” Grab Bar
Brushed Nickel Finish
☐ YG0336BN – 36” Grab Bar
Brushed Nickel Finish
☐ YG0342BN – 42” Grab Bar
Brushed Nickel Finish
☐ YG0312BG – 12” Grab Bar
Brushed Gold Finish
☐ YG0318BG – 18” Grab Bar
Brushed Gold Finish
☐ YG0324BG – 24” Grab Bar
Brushed Gold Finish
☐ YG0336BG – 36” Grab Bar
Brushed Gold Finish
☐ YG0342BG – 42” Grab Bar
Brushed Gold Finish
☐ YG0312NL – 12” Grab Bar
Polished Nickel Finish
☐ YG0318NL – 18” Grab Bar
Polished Nickel Finish
☐ YG0324NL – 24” Grab Bar
Polished Nickel Finish
☐ YG0336NL – 36” Grab Bar
Polished Nickel Finish
☐ YG0342NL – 42” Grab Bar
Polished Nickel Finish
Grab Bar posts and bars are constructed
of stainless steel.
Stock Number: Grab Bar
By MOEN
25300 AL MOEN DRIVE • NORTH OLMSTED, OH 44070
CORPORATE HEADQUARTERS: (800) 321-8809 • FAX: (800) 848-6636
INTERNATIONAL: (440) 962-2000 • FAX: (440) 962-2726
CUSTOMER SERVICE (USA): (800) 882-0116 • FAX: (888) 379-2720
WWW.MOEN.COM
©
Copyright Moen, Inc.
To preserve the ne nish of this product, clean only with a soft
damp cloth. Dry well. Do not use commercial or abrasive cleaners.
1. Please note that screws MUST be mounted into a wood stud for secure installation.
2. Decide whether you would like to position your grab bar horizontally, vertically or at an angle,
remembering that BOTH ends of the grab bar MUST be positioned over a wood stud (unless using
secure mount anchors).
3. For easier installation and mounting remove 3 set screws from each ange and remove bar from
SecureMount™ Flange.
4. Remove cover and re-assemble ange to bar by tightening 3 set screws.
5. Place grab bar and mark three mounting locations on each of the two grab bar anges with a pencil.
6. Drill 1/8" diameter pilot holes at each screw location. Make sure to drill into the stud.
7. Install 3 screws and washers each SecureMount™ ange and tighten until secure. If desired, apply
silicone caulk to the back of the SecureMount™ plate to guard against water penetration.
8. After screws are installed each side, dis-assemble bar from SecureMount™ ange by removing
set screws.
9. Re-install covers.
10. Place bar over SecureMount™ anges and tighten all set screws.
11. Snap on covers.
2-3/4”
(70mm)
Diameter
3-1/4”
(83mm)
Length
(A)
Length
(B)
Dim. A
Dim. B
YG0312
12.00
15.25
18.00
21.25
24.00
27.25
36.00
39.25
42.00
45.25
YG0318
YG0324
YG0336
YG0342
2-3/4”
(70mm)
Diameter
3-1/4”
(83mm)
Length
(A)
Length
(B)