Specification

Kingsley® Technical Specication
Grab Bar YG5400
Stock Numbers:
YG5412CH – 12" Grab Bar
Chrome Finish
YG5412BN – 12" Grab Bar
Brushed Nickel Finish
YG5412ORB – 12" Grab Bar
Oil Rubbed Bronze
YG5418CH – 18" Grab Bar
Chrome Finish
YG5418BN – 18" Grab Bar
Brushed Nickel Finish
YG5418ORB – 18" Grab Bar
Oil Rubbed Bronze Finish
YG5424CH – 24" Grab Bar
Chrome Finish
YG5424BN – 24" Grab Bar
Brushed Nickel Finish
YG5424ORB – 24" Grab Bar
Oil Rubbed Bronze
YG5430CH – 30" Grab Bar
Chrome Finish
YG5430BN – 30" Grab Bar
Brushed Nickel Finish
YG5436CH – 36" Grab Bar
Chrome Finish
YG5436BN – 36" Grab Bar
Brushed Nickel Finish
YG5442CH – 42" Grab Bar
Chrome Finish
YG5442BN – 42" Grab Bar
Brushed Nickel Finish
Materials:
Grab Bar posts and bars are stainless steel.
Compliance:
CSI grab bars meet or exceed the applicable
requirements of the following standards:
• ANSI A117.1
• ASTM F446
• CSA B45
• CSA B651
Loaded Tested to w ithstand 500 lbs when
securely installed per instructions. 12" long grab
bars are intended for vertical installation only.
Installation Instructions:
1 Please note that screws MUST be mounted into a wood stud for secure installation.
2. SlidetheendcoverawayfromthehubendtoexposetheSecureMount™mountingange.
3. Locate the studs behind the wall by using a stud sensor or other stud locating method. Studs are
usually 16" apart; locate the center of each stud.
4. PlacethegrabbaronthewallwheredesiredsothattheSecureMount™mountingangeis
positioned over a wood stud. Use a level to verify desired placement.
Decide whether you would like to position your grab bar horizontally, vertically or at an angle,
remembering that BOTH ends of the grab bar MUST be positioned over a wood stud. Note: Diagonal/
angled installation is possible only with grab bars 24" or longer.
5. Withapencil,markthreeofthemountinglocationsoneachofthetwograbbarangesas
indicated in the packed instructions.
Toensureproperinstallation,theSecureMount™angemusthavescrewsineachofthepositions
indicated in the packed instructions.
6. Remove the grab bar from the wall and drill 1/8" diameter pilot holes at the marked screw locations.
If desired, apply silicone caulk to the back of the decorative cover to guard against water penetration.
7. Tomountthegrabbar,repositiononeendofthegrabbarSecureMount™mountingangeover
the marked holes. NOTE: THE MOUNTING FLANGE WILL ROTATE. ROTATE THE FLANGE SO
THAT IT IS FLUSH AGAINST THE WALL AND THEN PROCEED WITH THE NEXT STEP.
8. Usingthescrewdriver,screwthewoodscrewsintotheSecureMount™mountingangeatoneendof
thegrabbar.Thenscrewthewoodscrewsintothemountingangeattheotherendofthegrabbar.
9. Tighten the screws until secure
10. SlidetheendcoverovertheSecureMount™mountingange,rotatingtondthecorrecttbefore
snapping into place.
Cleaning Instructions:
Topreservethenenishofthisproduct,cleanonlywithasoftdampcloth.Drywell.
Do not use commercial or abrasive cleaners.
Stock Number: _________________________ Grab Bar
By Moen Incorporated
25300 AL MOEN DRIVE • NORTH OLMSTED, OH 44070
CORPORATE HEADQUARTERS: [phone] • FAX: [phone]
INTERNATIONAL: (440 ) 962-2000 • FAX: [phone]
CUSTOMER SERVICE (USA): 800-882-0116 • FAX: [phone]
WWW.MOEN.COM
©
Copyright Moen Incorporated
Dimensions:
1.25
1.5
2.925
Ø 2.95
B
A
Dim. A Dim. B
YG5412 12 14.95
YG5418 18 20.95
YG5424 24 26.95
YG5430 30 32.95
YG5436 36 38.95
YG5442 42 44.95