Specification Sheet

Grab Bar
posts and bars are
aluminum. Skirt Rings are brass.
q YG5412CH – 12” Grab Bar
Chrome Finish
q YG5412CP – 12” Grab Bar
Chrome / Polished Brass Finish
q YG5412BN – 12” Grab Bar
Brushed Nickel Finish
q YG5418CH – 18” Grab Bar
Chrome Finish
q YG5418CP – 18” Grab Bar
Chrome / Polished Brass Finish
q YG5418BN – 18” Grab Bar
Brushed Nickel Finish
q YG5424CH – 24” Grab Bar
Chrome Finish
q YG5424CP – 24” Grab Bar
Chrome / Polished Brass Finish
q YG5424BN – 24” Grab Bar
Brushed Nickel Finish
q YG5430CH – 30” Grab Bar
Chrome Finish
q YG5430CP – 30” Grab Bar
Chrome / Polished Brass Finish
q YG5430BN – 30” Grab Bar
Brushed Nickel Finish
q YG5436CH – 36” Grab Bar
Chrome Finish
q YG5436CP – 36” Grab Bar
Chrome / Polished Brass Finish
q YG5436BN – 36” Grab Bar
Brushed Nickel Finish
q YG5442CH – 42” Grab Bar
Chrome Finish
q YG5442CP – 42” Grab Bar
Chrome / Polished Brass Finish
q YG5442BN – 42” Grab Bar
Brushed Nickel Finish
Compliance:
CSI grab bars meet or exceed the
applicable requirements of the
following standards:
ICC/ANSI A117.1
ASTM F446
CSA B45
CSA B651
Load Tested to withstand 300 lbs when
securely installed per instructions.
12” long grab bars are intended for
vertical installation only.
25300 AL MOEN DRIVE • NORTH OLMSTED, OH 44070 [phone] •
FAX: [phone] • INTERNATIONAL: (440) 962- 2000 •
FAX: (440) 962
-
2726 CUSTOMER SERVICE (USA): 800
-
882
-
0116
Tools Required: 1/8” drill bit and drill, Phillips screwdriver, Tape and Level
Hardware kit contents: 6 screws
1. Please note that all screws must mount into a wood stud.
2. Pull up and slide the skirt ring away from the hub end to expose the mounting
screw holes on both hubs.
3. Locate the studs behind the wall by using a stud sensor or another stud locating
method. Place the grab bar on the wall where de
sired so that all the mounting holes
are positioned over a wood stud. Use a level if desired to verify placement.
4. With a pencil, mark all six mounting hole locations.
5. Remove the grab bar from the wall and drill 1/8” diameter pilot holes at the six
marked screw locations. If desired, apply silicone caulk to the back of the grab bar
hubs to guard against water penetration.
6. Mount the grab bar using all 6 of the #10 x 2 ½” long wood screws provided.
Tighten screws until secure.
7. Slide the skirts back into place and press onto the hubs to secure.
Note: Grab bars are to be mounted to a secure surface. Creative Specialties
International shall not accept responsibility for any and all damage caused by lack of
wall strength or improper installation. It is the responsibility of the architect, builder
and installer to ensure that the mounting area is secure and that proper mounting
hardware is used for installation.
Stock Number:
______________________Grab Bar
By CSI Bath Furnishings
Materials:
Installation Instructions:
Stock Numbers:
Dimensions:
Grab Bar
YG5400
Kingsley Technical Specification
To preserve the fine finish of this product, clean only with a soft damp
cloth. Dry well. Do not use commercial or abrasive cleaners.

Copyright CSI Bath Furnishing Division of Moen 02/22/01
Literature #BA1125
Cleaning Instructions:
Dim. A
Dim. B
YG5412 12.00 14.95
YG5418
18.00
20.95
YG5424 24.00 26.95
YG5430
30.00
32.95
YG5436
36.00
38.95
YG5442
42.00
44.95