INSTALLATION AND OPERATION MANUAL GAS TARGET TOP / STATIC OVEN RANGE G570 232426-8
MANUFACTURED BY Moffat Limited Christchurch New Zealand INTERNATIONAL CONTACTS AUSTRALIA Moffat Pty Limited E.Mail: Main Office: Service: Spares: Customer Service: vsales@moffat.com.au (tel): +61 (03) 9518 3888 (fax): +61 (03 9518 3833 (tel): 1800 622 216 (tel): 1800 337 963 (tel): 1800 335 315 (fax): 1800 350 281 CANADA Serve Canada Web: E.Mail: Sales: Service: www.servecanada.com info@servecanada.com (tel): 800 551 8795 (Toll Free) (tel): 800 263 1455 (Toll Free) NEW ZEALAND Moffat Limited Web: E.
Contents List Blue Seal Gas Target Top Static Oven Range G570 Gas Target Top Static Oven Range. Introduction .............................................................................................. 2 Specifications ............................................................................................ 3 Model Numbers Covered in this Specification General Gas Supply Requirements Gas Connection Dimensions .............................................................................................
Introduction We are confident that you will be delighted with your BLUE SEAL Target Top Gas Static Oven Range, and it will become a most valued appliance in your commercial kitchen. To ensure you receive the utmost benefit from your new Blue Seal appliance, there are two important things you can do. Firstly: Please read the instruction book carefully and follow directions given. The time taken will be well spent.
Specifications Model Numbers Covered in this Specification G570 Gas Target Top Static Oven Range. General A commercial heavy duty, general purpose fully modular, gas fired Target Top Static Oven Range, having a high output, two stage double-ring cast iron burner offering accurate temperature control and infinitely variable heat with heat radiating out from centre of Target Top. Main Burner is located beneath removable cast target top plates.
Dimensions G570 4
Installation Installation Requirements NOTE: It is most important that this appliance is installed correctly and that operation is correct before use. Installation shall comply with local gas and health and safety requirements. This appliance shall be installed with sufficient ventilation to prevent occurrence of unacceptable concentrations of health harmful substances in the room, the appliance is installed in.
Installation Clearances NOTE: Only non-combustible materials can be used in close proximity to this appliance. Combustible Surface Non Combustible Surface Left / Right Hand Side 50 mm 0 mm Rear 50 mm 0 mm Assembly Caution This appliance is for professional use and is only to be used by qualified persons. Only authorised service persons are to carry out installation, servicing or gas conversion operations. NOTE: All Models are delivered completely assembled.
Installation NOTE: (**) Measure burner operating pressure at target top hob manifold test point with target top burner (Inner and outer ring) operating at full setting. NAT, LPG & Butane Only - Operating pressure is ex-factory set and is not to be adjusted, apart from when converting between gasses, if required. TOWN GAS Only - Burner operating pressure is to be adjusted using adjustable gas regulator supplied.
Operation Operation Guide Caution This appliance is for professional use and is only to be used by qualified persons. Only authorised service persons are to carry out installation, servicing or gas conversion operations. Components having adjustments protected (e.g. paint sealed) manufacturer should not be adjusted by the user / operator. 1. 2. by the Blue Seal appliances have been designed to provide simplicity of operation and 100% safety protection.
Operation Lighting Pilot Burner - (Target Top) 1. Remove centre casting with casting removal tool. 2. Depress control knob and rotate anti-clockwise to ‘PILOT’ position. 3. With control knob depressed, manually light pilot burner located in front of main burner. 4. Hold in control knob for approximately 10 to 15 seconds, then release. 5. Pilot burner should remain alight. If not repeat Items 2 to 4 above until pilot burner lights. Lighting Main Burner - (Target Top) 1.
Operation Lighting Oven Pilot Burner Pilot Burner viewing holes ! IMPORTANT DO NOT USE aluminium foil or trays directly on cast iron sole plate(s). NEVER block or cover openings on each side of sole plate(s). This oven is fitted with a pilot as a standard option and flame failure protection, which is incorporated by way of a thermoelectric system for main burner. Flame failure protection will shut ‘Off’ gas supply to burner in the event that pilot burner goes out, so that un-burnt gas is not expelled.
Operation Control Knob in ‘Off’ Position Oven ‘Shut-Down’ NOTE: DO NOT attempt to rotate Thermostat Control Knob anti-clockwise back to ‘O’ Off position as Knob and Gas Valve will be damaged. 1. To turn 'Off' oven completely, partially depress thermostat control knob whilst turning clockwise to 'O' Off position, pilot burner will extinguish. DO NOT fully depress Thermostat Control Knob whilst trying to rotate clockwise to ‘O’ Off position as Knob and Gas Valve will be damaged.
Cleaning and Maintenance C AUTIO N : Caution Always turn ‘Off’ gas supply before cleaning. This appliance is not water proof. Do not use water jet spray to clean interior or exterior of this appliance. General Clean the Target Top regularly. A clean appliance looks better, will last longer and will perform better. Carbonised grease on cooking surface will hinder transfer of heat from cooking surface to food. This will result in loss of cooking efficiency.
Cleaning and Maintenance c. DO NOT use water on castings while they are still hot as cracking may occur. Should it be necessary to clean castings, allow castings to cool and then remove for cleaning. Clean using a soft cloth moistened with a mild detergent and hot water solution and a scrubbing brush. Dry thoroughly with a dry cloth. d. Remove drip tray and clean with a mild anti bacterial detergent and hot water solution using a soft bristled brush. Dry drip tray thoroughly with a dry cloth. e.
Fault Finding This section provides an easy reference guide to the more common problems that may occur during operation of your appliance. The fault finding guide in this section is intended to help you correct, or at least accurately diagnose problems with your appliance. Although this section covers the most common problems reported, you may encounter a problem not covered in this section.
Gas Conversion and Specifications Conversion Procedure Caution Ensure Appliance is isolated from gas and electrical supplies before commencing servicing. NOTE: These conversions should only be carried out by qualified persons. All connections must be checked for leaks before re-commissioning appliance. Adjustment of components that have adjustments / settings sealed (e.g.
Gas Conversion and Specifications Pilot Burner 1. 2. 3. 4. 5. Disconnect gas supply tube from base of pilot burner. Remove pilot burner and thermo couple retaining plate. Remove pilot burner from mounting bracket. Remove injector and spring from pilot burner and replace with correct size injector as shown in ‘Gas Specifications Tables’ at rear of this section. Refit pilot burner to retaining bracket - ensuring pilot burner ports are at same height as thermocouple.
Gas Conversion and Specifications Static Oven 1. Main Burner Carry out the following: Remove lower lintel at front of oven. Thermocouple Pilot Burner Open oven door and remove sole plate(s). Remove main burner. Disconnect pilot supply tube from pilot burner to access pilot injector. 2. With Main Burner removed, ensure aeration gap is adjusted for type of gas being used as shown in ‘Gas Specifications Tables’ at end of this section. 3.
Gas Conversion and Specifications Gas Type Identification Label On completion of gas conversion, replace gas type identification label located at:- Rear of appliance, above gas connection. - Beside rating plate. Commissioning Before leaving the installation; 1. Check all gas connections for leakage using soapy water or other gas detecting equipment. Warning DO NOT USE A NAKED FLAME 2. 3. TO CHECK FOR GAS LEAKAGES.
Replacement Parts List Replacement Parts List IMPORTANT: Only genuine authorized replacement parts should be used for servicing and repair of this appliance. Instructions supplied with parts should be followed when replacing components. For further information and servicing instructions, contact your nearest authorized service branch (contact details are as shown on reverse of front cover of this manual). When ordering replacement parts, please quote part number and description as listed below.
Replacement Parts List General 227012 227013 014997 227892 227893 227896 227850 229674 Centre Casting. Half Plate Casting. Casting Removal Tool. Oven Side Rack LH. Oven Side Rack RH. Oven Rack. Adjustable Leg (150 mm) Rear Roller Assy. Regulators Gas Type Gas Regulators Part No. Nat. Gas LPG, Butane 228531 Town Gas 230185 Description ¾” BSP F/F Convertible. ¾” BSP F/F Adjustable. Accessories 228800 Ranges 900 mm Plinth Kit. Gas Conversion Kits Model G570 Gas Type to Convert to Nat.
