30DSERIES E31D4 (Digital Operation) Installation and Operation Manual 234144-9
MANUFACTURED BY Moffat Limited Christchurch New Zealand INTERNATIONAL CONTACTS AUSTRALIA Moffat Pty Limited Web: E.Mail: Main Office: Service: Spares: Customer Service: www.moffat.com.au vsales@moffat.com.au (tel) +61 (03) 9518 3888 (fax) +61 (03) 9518 3833 (tel): 1800 622 216 (tel): 1800 337 963 (tel): 1800 335 315 (fax): 1800 350 281 CANADA Serve Canada Web: E.Mail: Sales: Service: www.servecanada.com info@servecanada.
Contents List E31 Turbofan Convection Oven. Model Numbers Covered in this Manual E31D4 - Turbofan Oven - 4 Tray Convection Oven. Introduction ........................................................................................................... 2 Safety Information Specifications ......................................................................................................... 3 Installation .......................................................................................................
Introduction Before using your new oven, please read this instruction manual carefully, pay particular attention to any information labelled ‘WARNING’, ‘CAUTION’, ‘IMPORTANT’ or ‘NOTE’ in this manual. Warning Indicates a hazardous situation which, if not avoided, will result in death or serious injury. Caution Indicates a hazardous situation which, if not avoided, will result in minor or moderate injury. This manual must be kept by the owner for future reference.
Specifications E31D4 Oven Power Ratings 208V, 1P+N+E, 50/60HZ, 2.9 kW 220V, 1P+N+E, 50/60HZ, 3.1 kW 230-240V, 1P+N+E, 50/60HZ, 3.
Installation Installation Requirements Important: • Installation shall comply with local electrical, health and safety requirements. • It is most important that this oven is installed correctly and that oven operation is correct before use. • If you have any questions regarding the proper installation and / or operation of this oven, please contact your local Turbofan distributor. Unpacking Clearances 1.
Installation Electrical Connection Warning This oven must be earthed / grounded. If the supply cord is damaged, it must be replaced by a suitably qualified person in order to avoid a hazard. Each oven should be connected to an adequately protected power supply and an isolation switch mounted adjacent to, but not behind the oven and must be readily accessible to the operator. This switch must be clearly marked and readily accessible in case of fire.
Operation Operation Guide Warning Warning Take care when opening the oven door during baking. Let hot air and steam escape before removing or replacing food as the steam produced can cause steam burns. Some parts of this oven will become VERY HOT during use and could cause burns if touched. • Turbofan Ovens have been designed to provide simple operation. • This oven is intended for use in a commercial kitchen and must only be put to the use for which it was intended, i.e. cooking food product.
Operation Using the Oven - Manual Mode 1. To check actual oven temperature during preheat or cooking, press ‘Temperature’ button. Actual temperature will display briefly on ‘Temperature Display’ before the display reverts to the pre-set temperature. TURN ‘ON’. Press ‘On-Off’ button. Temperature Dislay. Temperature Display will show actual temperature. 2. Heating ‘On’ Indicator SET TEMPERATURE. + to increase the temperature. - to decrease the temperature.
Operation Cooking in Program Mode 1. TURN ‘ON’. Press ‘On-Off’ button. Press ‘Programs’ button. Program Mode Indicator Heating ‘On’ Indicator Temperature Dislay. Temperature Display will show program selected. 2. To check actual oven temperature during preheat or cooking, press ‘Temperature’ button. Actual temperature will display briefly on ‘Temperature Display’ before the display reverts to the pre-set temperature. SELECT A PROGRAM. + to scroll forward through programs.
Operation Setting the Oven Programs Oven can be pre-programmed with up to 20 Program’s. When you receive your oven, the controller is not programmed. To set programs, carry out the following for each program required:- 1. ENTER PROGRAMMING MODE. Press ‘Programs’ button to enter ‘Programming’ mode. 2. SELECT PROGRAM REQUIRED. Heating ‘On’ Indicator Rotate ‘Temperature Control’ to program required. Temperature Display will show program selected.
Operator Accessible Parameters Setting the Operator Accessible Parameters With the Oven in ‘Stand-By’ mode:- 1. ENTER THE OPERATOR PARAMETER MODE. Press 'Grill / Broil' and 'Start / Stop' buttons together. ‘Temperature’ Display will show ‘PAS’. The ‘Time’ Display will flash. 2. SET PASSWORD. Rotate ‘Timer Control’ to set password; (123) (Operator Password). Press ‘Light On / Off’ button to confirm password. ‘Temperature’ Display will show one of Parameter Codes.
Cleaning and Maintenance Cleaning Guidelines c. Pull side racks forward to disengage the location pins at the rear of rack from the rear wall of the oven and remove the racks from the oven. Caution d. Clean all racks with a mild anti bacterial detergent and hot water, using a soft bristled brush. Always turn off electrical power at the mains supply before commencing cleaning. e. Dry the racks thoroughly with a dry cloth. f.
Cleaning and Maintenance Door Seal a. To remove door seal, pull the 1 piece seal forward until it pulls out of the location groove around the oven. Note the way the seal is fitted to the oven, with the lip facing inwards. Door Glass Cleaning • Ensure that the oven door is cool before cleaning the oven door glass. a. Open the oven door. b. Lift up the bottom of the inner glass at the centre of the door to unlock from the inner glass retaining catches and swing the glass inwards towards the oven. b.
Fault Finding This section provides a reference to the more common problems that may occur during the operation of your oven. This fault finding guide is intended to help you correct and accurately diagnose problems with your oven.
Electrical Schematics Electrical Schematic E31D4 Turbofan Oven 14
Replacement Parts List Important: Only genuine authorized replacement parts should be used for the servicing and repair of this oven. The instructions supplied with the parts should be followed when replacing components. For further information and servicing instructions, contact your nearest authorized service provider or Turbofan Dealer. When ordering replacement parts, please quote the part number and the description as listed below.
Appendix 1 - Oven Door Reversal 11. Remove inner glass latching studs and fit to opposite side of door using Loctite 243 to secure. Reversing the Oven Door • Refit all screw fasteners using a low-mid strength thread locking adhesive unless otherwise stated. • Door reversal should only be carried out by a suitably competent person. Remove Latching Studs Remove the Oven Door Inner Glass. 1. Open the oven door and open the door inner glass. 2.
Appendix 1 - Oven Door Reversal 18. Remove Blanking Screw and Door Catch from front of oven and swap around (refer ‘Adjusting Door Catch’). Door Catch Adjust Door for Correct Alignment. Check alignment and operation of the door. Ensure that the door is correctly aligned horizontally and vertically. 1. To align, slacken off the upper and lower hinge plates and correctly align the door. Re-tighten both hinge plates. 2. Check that the roller catch correctly retains door in the closed position.
