LW007-PIR APP Guide MOKO TECHNOLOGY LTD. Version 1.0 www.mokosmart.
CONTENT 1 About this Manual............................................................................................................................. 3 2 MKLoRa APP ...................................................................................................................................... 3 2.1 Install MKLoRa APP ............................................................................................................. 3 2.2 Connect to LW007-PIR................................................
LW007-PIR 1 About this Manual The purpose of this manual is to outline how to use MKLoRa APP for LW007-PIR parameters configuration. 2 MKLoRa APP For the detailed operation of the MKLoRa app to configure and read device information, please refer to the following instructions: 2.1 Install MKLoRa APP User can get the APP download link by search“MKLoRa”in your phone APP store: Please allow Bluetooth to be enabled during the installation process.
LW007-PIR 2.3 Configure LW007-PIR Parameters When you log into the device successfully, you will enter the main page. There are four parts of the parameter configuration: LORA, GENERAL, BLUETOOTH and DEVICE. 2.3.1 LORA Parameters In this page, user can configure parameter for LoRa Part: LoRaWAN Status: Indicates the status of the LoRaWAN network connection. Connection Settings: Configure LoRaWAN network parameters. Application Settings: Configure LoRaWAN application parameters. 4 www.mokosmart.
LW007-PIR 2.3.1.1 Connection Settings LoRaWAN Mode: LoRaWAN join-in mode selection DevEUI/AppEUI/AppKey: Network parameters in OTAA mode. DevEUI/AppEUI/DevAddr/AppKey/NwkSKey: Network parameters in ABP mode. Region/Subnet: Device frequency band selection, AS923/ AU915 /CN470 /CN779 /EU433 /EU868 /KR920 /IN865 /US915 /RU864 can be set. Message Type: Uplink payload type, it can be set unconfirmed or confirmed, the default is confirmed.
LW007-PIR Note: Please do not modify advanced settings unless necessary. 2.3.1.2 Application Settings Time Sync Interval: It is used to sync the device time via MAC command. The default is 1, means that the device's time will be synchronized every 1 hour via LoRaWAN MAC commands. The value ranges from 0 -255H. 0 means disable. Network Check Interval: The device will periodically check the LoRaWAN network status via MAC command.
LW007-PIR 2.3.2.1 PIR Settings Function Switch: The function switch of PIR detection. The default is ON. Report Interval: Information Payload reporting interval when PIR is continuously triggered. The default is 10, the unit is minute. The value ranges from 10 -60 mins. PIR Sensitivity: Users can adjust the trigger sensitivity according to different scenarios, so as to adjust the monitoring range. The default is Medium. It can be set as Low or medium or High.
LW007-PIR 2.3.2.3 T&H Settings Function Switch: The function switch of T&H monitoring. The default is ON. Sample Rate: The sample rate of temperature and humidity data. The default is 1s. The value ranges from 1~60s. Temp Threshold Alarm: The function switch of temperature threshold alarm function. The default is OFF. MAX: Upper limit value for temperature threshold alarm, the default is 30℃. The value ranges from -30~60℃. Min: Lower limit value for temperature threshold alarm, the default is 10℃.
LW007-PIR 2.3.3 Bluetooth Settings ADV Name: The advertising name of the device, up to 16 characters. ADV Interval: Bluetooth advertising interval. The default is 1000ms. It ranges from 1-100, the unit is 100ms. Beacon Mode: The device can be set to beacon mode or configuration mode. The default is ON. Connectable: User can select the connectable state or the unconnectable state. The default is connectable state.
LW007-PIR 2.3.4.1 Device Information DFU (Update Firmware): To update the firmware via the DFU should use the upgrade package that MOKO provides with ZIP format. If you use an android phone, place the ZIP file of firmware upgrade package into the phone folder, select the upgrade package file from the OTA page of the APP, and click to upgrade. If you use an iPhone, user need to share the upgrade package file with MKLoRa via computers and iTunes tools.
LW007-PIR Recommend configuration: Categories Parameter Recommend Description Value PIR Settings Hall Settings T&H Settings Function Switch ON Report Interval 30 mins PIR Sensitivity Medium PIR Delay Time High Function Switch OFF This function is not required for this scenario Function Switch ON Simultaneous environmental monitoring possible Sample Rate 1s Temp Threshold Alarm RH Threshold Alarm ON ON There is a possibility that it may be occupied for a long time, so the reporting int
LW007-PIR Temp Change Alarm RH Change Alarm ON ON Timely alarm notification of temperature abnormalities (Rapid temperature change) Timely alarm notification of humidity abnormalities (Rapid humidity change) 3 Revision History Version Description Editor Date 1.0 Initial version Allen 12 2021-12-20 www.mokosmart.
LW007-PIR MOKO TECHNOLOGY LTD. 4F,Buidling2, Guanghui Technology Park, MinQing Rd, Longhua, Shenzhen, Guangdong, China Tel:86-755-23573370-829 Support_lora@mokotechnology.com https://www.mokosmart.
