SDS

ManualsBrandsMold Armor ManualsPaint1 Gal. Pre- Paint Cleaner

04/10/2018Revision:

04/10/2018Printed:

Page: 1

Mold Armor Pre-Paint Cleaner1

SAFETY DATA SHEET

02/15/2018Supersedes Revision:

Mold Armor Pre-Paint Cleaner1

Product Name:

WM Barr & Company

Company Name:

6750 Lenox Center Court

Memphis, TN 38115

Suite 200

3E 24 Hour Emergency Contact

Emergency Contact:

(800)451-8346

WM Barr Customer Service

Information:

(800)398-3892

Mold and Mildew Stain Remover

Intended Use:

www.wmbarr.com

Web site address:

FG580

Product Code:

1. PRODUCT AND COMPANY IDENTIFICATION

2. HAZARDS IDENTIFICATION

P264: Wash hands thoroughly after handling.

P280: Wear protective gloves/protective clothing/eye protection/face protection.

GHS Precaution Phrases:

P302+352: IF ON SKIN: Wash with plenty of soap and water.

P321: Specific treatment see label.

P332+313: If skin irritation occurs, get medical advice/attention.

P362: Take off contaminated clothing and wash before re-use.

GHS Response Phrases:

No phrases apply.

GHS Storage and Disposal

Phrases:

H315: Causes skin irritation.

GHS Hazard Phrases:

Skin Corrosion/Irritation, Category 2

Warning

GHS Signal Word:

This material is classified as hazardous under OSHA regulations.

OSHA Regulatory Status:

Causes skin irritation.

May cause eye irritation.

Potential Health Effects

(Acute and Chronic):

CAS # Hazardous Components (Chemical Name)

3. COMPOSITION/INFORMATION ON INGREDIENTS

Concentration

7681-52-9 Sodium hypochlorite {Hypochlorous acid, sodium

salt}

< 5.0 %

1310-73-2 Sodium hydroxide {Caustic soda; Lye solution} < 1.0 %

Specific percentage of composition is being withheld as a trade secret.

Additional Chemical

Information

Licensed to W.M. Barr and Company: MIRS MSDS, (c) A V Systems, Inc.

GHS format

Summary of content (5 pages)

PAGE 1
SAFETY DATA SHEET Mold Armor Pre-Paint Cleaner1 Page: 1 Printed: 04/10/2018 Revision: 04/10/2018 Supersedes Revision: 02/15/2018 1. PRODUCT AND COMPANY IDENTIFICATION Mold Armor Pre-Paint Cleaner1 WM Barr & Company 6750 Lenox Center Court Suite 200 Memphis, TN 38115 Product Name: Company Name: Web site address: www.wmbarr.
PAGE 2
SAFETY DATA SHEET Mold Armor Pre-Paint Cleaner1 Page: 2 Printed: 04/10/2018 Revision: 04/10/2018 Supersedes Revision: 02/15/2018 4. FIRST AID MEASURES Emergency and First Aid Procedures: Inhalation: If user experiences breathing difficulty, move to air free of vapors. Administer oxygen or artificial respiration until medical assistance can be rendered. Skin contact: Wash with soap and large quantities of water for at least 15 minutes. Seek medical attention if irritation from contact persists.
PAGE 3
SAFETY DATA SHEET Mold Armor Pre-Paint Cleaner1 Page: 3 Printed: 04/10/2018 Revision: 04/10/2018 Supersedes Revision: 02/15/2018 8. EXPOSURE CONTROLS/PERSONAL PROTECTION CAS # Partial Chemical Name OSHA TWA ACGIH TWA Other Limits 7681-52-9 Sodium hypochlorite {Hypochlorous acid, sodium salt} No data. No data. No data. 1310-73-2 Sodium hydroxide {Caustic soda; Lye solution} PEL: 2 mg/m3 CEIL: 2 mg/m3 No data.
PAGE 4
SAFETY DATA SHEET Mold Armor Pre-Paint Cleaner1 Page: 4 Printed: 04/10/2018 Revision: 04/10/2018 Supersedes Revision: 02/15/2018 10. STABILITY AND REACTIVITY Stability: Unstable [ ] Stable [ X ] Conditions To Avoid Instability: No data available. Incompatibility - Materials To Incompatible with acids, ammonia, or other household chemicals. Do not mix with acids, ammonia, or other household chemicals as dangerous fumes may result.
PAGE 5
SAFETY DATA SHEET Mold Armor Pre-Paint Cleaner1 Additional Regulatory Information Page: 5 Printed: 04/10/2018 Revision: 04/10/2018 Supersedes Revision: 02/15/2018 This chemical is a pesticide product registered by the United States Environmental Protection Agency and is subject to certain labeling requirements under federal pesticide law.