Use Instruction

ITFIT BE7 manual_aw
Size: 70.5mm(w) x 90mm(h)
Instruction Manual
WIRELESS SPORTS EARPHONES
2019 AUG 01
Wireless Earphone
Model : BE7
Specification:
Bluetooth Version : 5.0
Effective Range : 10m
Frequency respon
se : 8Hz~20kHz
Impedance : 32 Ohm
Battery : 90mAh
Non-stop working time : Up to 6 hours
Charging time : Approx. 2 hours
Energy Saving mode : Auto power off
Dimensions : 49 x 47mm earbud,
500mm cord length
Weight : 19g
Contains:
1. 1 x Wireless Earphone
2. Removable ear tips (3 pairs):
Small / Middle (installed on Earphone) / Large
3. 1 x Micro USB charging cable
4. Instruction Manual
Bluetooth Pairing Quick Start Guide
Action
Press and hold “O” for about 2 seconds
Press and hold “O” for about 4 seconds
Press and hold “O” for about 5 seconds
Press and hold “O” for about 2 seconds
Press and hold “O” for about 1 second
Short pressing “+”
Short pressing –”
Long pressing “+
Long pressing “–
Press “O
Press and hold “O” for about 1 second
during the call When an incoming call
Press “O
Press and hold “O” for about 1 second
during the call
Short press “O
Press “O” twice
Press “O” twice
Press and hold “O” for about 1 second
LED Indicator
Blue LED flashes for 1 second
Red LED flashes for 1 second
Blue & Red LED flashes alternately
Blue LED flashes quickly & reconnects
automatically
Blue LED flashes once every 5
seconds
* Depending on whether the mobile device supports this feature
Function
Turn the earphone ON
Turn the earphone OFF
Bluetooth connection
(
First time to pair with mobile device
)
Bluetooth connection
(
Reconnected to mobile device after paired
)
Play or pause Music
Volume up
Volume down
Skip forward
Skip backward
Pick up a call
Reject the call
Terminate the call
Switch device during the call*
Switch caller in a call
(
Terminate current call
)
*
Switch caller in a call
(
Pause & Hold current call
)
*
Switch caller in a call
(
Switch back the on-hold call
)
*
Keep current caller & Reject a new coming call*
Instruction for use
Disposal of Electronic Products
1. Do not place the product as household waste;
2. Please dispose of discarded electronic products properly
according to local regulations.
3. Please participate in electronics recycling program.
How to charge
1. Open the charger port cover.
2. Connect the headset to USB power adaptor via Micro
USB cable.
3. The LED indicator will glow RED when charging.
4. The LED indicator will glow BLUE when the battery is full.
5. When the battery is low
Standby mode:
The LED indicator will
flash RED once every
second.
Working mode:
The LED indicator will flash
RED every 5 seconds.
Volume
button
+ /
-
Power
button
“O”
Removable ear tip
1.Press and hold the “O” button for about 5 seconds to
power on and put the earphone into paring mode.
2.The LED indicator will flash red and blue alternately.
3.Open the Bluetooth settings on your mobile device and
search for nearby Bluetooth devices.
4.Locate and select “BE7” entry from the list. When
pairing is successful, the LED will flash blue every 5
seconds. (Note that if the earphone will remember the
last device it was paired with and will automatically
reconnect whenever it is in range.)
Press & hold
fo
r about 5 secs.
Micro USB cable
Copyright @ 2019 ITFIT All rights reserved
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception,
which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more
of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
The device has been evaluated to meet general RF exposure requir
ement. The device can be used in portable
exposure condition without restriction
FCC ID: 2ANBQ-BE7

Summary of content (1 pages)