Instruction Manual CS-200 Series 1
Table of Contents Table of Contents .................................................................................................................................. 2 Introductions......................................................................................................................................... 3 Features ................................................................................................................................................ 4 Safety Instructions ..............
Introductions This CS-200 series, the latest state of the art digital conference control system with superb performance and elegant design, can be used for various conferencing. This conference system has the most advanced built-in digital control mode with 10 chairman microphones and 999 delegate microphones (the number of microphones used depend on actual requirement).
Features Main control unit of the Conference System 1. Digital Control Capability: Chairman’s Unit x10, Delegate’s Unit x 999 2. ID Settings of the Conference Unit: 10-Bit Dip Switch Adopted. 3. Numbers Ranged From 001 ~ 999, Totally 999 Delegate Units. 4. ID Position Code of Delegate Unit: 001~999, Totally 999 Codes. 5. ID Position Code of Chairman Unit: ＊01~ ＊10, Totally 10 Codes. 6.
Safety Instructions 1. Please read and observe these instructions before installing and using the apparatus. 2. Use only accessories specified by the manufacturer. The manufacturer is not liable for damage caused by the use of non-specified accessories. 3. Install the apparatus and its accessories carefully. Strike and fierce shaking may damage the apparatus. 4. Make sure the power cord is fixed properly. 5.
Installations & Connections 1.Connection between Conference Main control unit & Chairman/Delegate MIC. BXB BXB ! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: ．TO PREVENT ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK) ．NO USER SERVICEABLE PARTS TO QUALIFIED SERVICE PERSONNEL ~ AC FUSE 250V T8A MADE IN TAIWAN http://www.bxb.com.tw IOIOI DC FUSE D+ D- 1 10 L.Spearer Aux Output Conference Link Aux Input Mic Input SpeedDome BXB BXB TOP 1.
2. Connection between Main control unit & High speed dome Positioning System 2P Â ù µ ± ½u 16 PCS D+ D- D+ D- ! D+ D- FCS 3150/6150 卡訊電子實業有限公司 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: ．TO PREVENT ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK) ．NO USER SERVICEABLE PARTS TO QUALIFIED SERVICE PERSONNEL ~ AC FUSE 250V T8A MADE IN TAIWAN http://www.bxb.com.tw IOIOI DC FUSE D+ D- 1 10 L.
3. Basic Connection between Conference Main control unit & Software Control System ! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: ．TO PREVENT ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK) ．NO USER SERVICEABLE PARTS TO QUALIFIED SERVICE PERSONNEL ~ AC FUSE 250V T8A MADE IN TAIWAN http://www.bxb.com.tw IOIOI DC FUSE D+ D- 1 10 L.Spearer Conference Link Aux Output Aux Input Mic Input SpeedDome FCS 3150/6150 3.
CS-200 Operation & Function Instructions 1.Main control unit’s Front/Rear Panel Functions Instructions 1.1 【Front Panel】 5 6 ConferenceSystem Control Unit -8 Mic Mode Up Down Step Up Save 4 3 Aux Down Up -5 -2 0 +2 Power Down 1 2 1. POWER: power switch。 2. AUX volume control: Adjust the volume of the equipment connected to the AUX input jack 3. MIC volume control: Adjust the volume of the microphone connected to the microphone input jack 4.
1.2 【Rear Panel】 9 8 ! CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: ．TO PREVENT ELECTRIC SHOCK DO NOT REMOVE COVER(OR BACK) ．NO USER SERVICEABLE PARTS TO QUALIFIED SERVICE PERSONNEL ~ AC FUSE 250V T8A MADE IN TAIWAN http://www.bxb.com.tw IOIOI DC FUSE D+ D- 1 10 L.Spearer Aux Output Conference Link Aux Input Mic Input SpeedDome 7 6 5 4 3 2 1 1. MIC Input: dynamic microphone input terminal（XLR） 。 2. AUX Input: external sound input terminal (XLR)。 3.
2.Power On 2.1 After confirming all the above adjustments and control wiring is done. Switch the power on and the LCD will be displayed the following information (including the software version):： B X B 1 . 7 0 C o n f e r e n c e V e r s i o n P A S y s t e m 2.2 Later, the system will be in connection test mode, the system will start scanning all connected conference microphones; LCD will be displayed the following information: M e m o r · · · y C h e c k · · · O K 2.
3.LCD Instructions 1 2 3 4 N M O A O O P U : D E : N o r m a l E N - M I C : 0 2 T O - O F F : 3 0 5 S P E E D M I C ( 0 0 1 ) 6 S P E E D ( N o n e ) ○,1 ○,21 ○, M i c S e c D O M E S E T T I N G D O M E 0 1 A D R 0 0 1 D O M E B u t M O D E t o n V o i ○,3 ○,4 ○,5 ○,6 c e 1. NO: Using microphone’s ”ID code”: 3 groups of ID code are displayed per page. i. Chairman microphone’s”ID code”:1 ~ 10 ii. Delegate microphone’s”ID code”:001 ~ 999 2. MODE: i. Normal：Normal Mode ii.
4.System’s Operations & Settings 4.1 Using MIC. ID Checking 4.1.1 When the conference unit is using, the red LED of microphone will be constantly on. Meanwhile, its ID code will be displayed on the LCD of main control unit. 4.1.2 Less than 3 using microphones, you can see the ID code on the preset menu. 1 2 3 4 N M O A O O P U : 0 0 D E : E N - M T O - O 1 0 0 2 0 0 3 N o r m a l I C : 0 2 M i c F F : 3 0 S e c 4.1.3 Over 3 using microphones,” ” icon will be displayed on the up-right of the LCD.
4.2 Conference Mode Settings 4.2.1 Press”MODE” button move” ◘” icon to MODE Normal (is flashing) press”UP” or ”DN” change the conference mode. 1 N O 2 ◘ M O 3 O P 4 A U : 0 0 D E : E N - M T O - O 1 0 0 2 0 0 3 N o r m a l I C : 0 2 M i c F F : 3 0 S e c 4.2.2 The following conference modes can be set. ※The chairman, who is not subject to the following conference mode, can speak anytime freely.
simultaneously by pressing the 5 multi-function buttons of chairman unit）. When the numbers of speaker and requesting speakers are over three, you will see this arrow icons →、←、↔ displayed on LCD of Chairman unit and main unit, indicating →（next page）、 ←（last page） 、↔（continued last and next pages）.
4.3 Settings of the limiting number of simultaneously usable delegate microphone 4.3.1 You can select “Open- Mic: ALL Mic” mode (see below ) or set up the limiting number of simultaneously usable delegate microphone ranged from 1~30. 4.3.2 Press ”MODE” button move” ◘” to OPEN –MIC mode No. 03 Mic will be flashing press ”UP” or ”DN” button again change the No. 1 N 2 M 3 ◘ O 4 A O O P U : 0 0 D E : E N - M T O - O 1 0 0 2 0 0 3 N o r m a l I C : 0 3 M i c F F : 3 0 S e c 4.3.
4.5【Save】Settings 4.5.1 When all above settings finished, if you want to save them as default value, you only need to push “SAVE” button. When it’s done, the saved setting is permanent. Power failures of switching off do not clear the default value. 4.5.2 When “SAVE” button is pressed, the LCD will be displayed in the following information. S a v e . . . . . . . . . O K 4.6 Speed Dome Camera Settings 4.6.
5 ◘ S P E E D D O M E S E T T I N G M I C 0 0 1 D O M E 0 1 A D R ( 0 0 1 ) 4.6.7 Each speed dome has 128 Programmable Preset Positions. 4.6.7.1 When the figure under ADR column displayed 001, it is the 1st Programmable Preset Positions. 4.6.7.2 When the figure under ADR column displayed OFF, the function of Auto-Image Tracing & Positioning is disabled. 4.6.
4.6.11 Auto-return (HGO) After setting, the camera will shoot the preset point (the whole meeting area or at the chairman) when none microphone is in use. Press "MODE" button switch "◘" to SPEED DOME SETTING (the second page) ( ) will be shown below MIC press "UP" or "DN" button and select HGO select camera number under DOME select camera position under ADR.
4.7 Speed Dome Camera Mode Settings 4.7.1 Auto-Image Tracing & Positioning Control Mode 4.7.1.1” None” mode: Auto-Image Tracing & positioning is disabled. 4.7.1.2” Button” mode: The speed dome will be tracing & positioning the image while the “TALK” button is being pressed. The images of Speed Dome will be positioned to the last talking microphone. By pressing the “TALK” button, the chairman or delegates could have the images of positioned again 4.7.1.
Press ”STEP” button move（）to “Scan” press ”SAVE” button. 7 ◘ M I C C H E C K I N G T e s t M O D E ( S c a n ) The following display will be lasted about 30 sec. E R A S E M E M O R Y P L E A S E W A I T . After that, FCS3000/6000 will start checking all microphone’s ID installed. It will take about 60 seconds. □ □ □ □ □ □ C H E C K I N G M I C : ： M I C C O U N T E R ： E R R O R CHECKING MIC（Checking correct microphone ID） ：Delegate’s ID: 000~999, Chairman ID:＊ 01~＊10.
CHECKING MIC (Checking correct microphone ID): Under “Test” status, it will test only those microphones connected. MIC COUNTER（All microphone connected） ：Under “Test” status, it will be displayed the number of microphones connected correctly ERROR（Error MIC ID Code）：Under “Test” status, it will be displayed error ID codes. ※If the numbers of microphones are increased or reduced, you have to repeat step 4.8.2.1, and then the system will be automatically scanned and detected all the microphones.
4.10. Video Auto Switch 4.10.1 Multi-image overcome display switch: with a multiplexer, images from multi-camera can run auto-overcome display. 4.10.2 Setting: Press “MODE” button switch ” ◘” to 9. VIDEO AUTO SWITCH（on the 6th page） ( ) will be shown beside YES press “STEP” to switch YES(auto-overcome)/NO(shown with divided screen).
4.12 Volume Mode Settings To set up the volume of PA system, please press the “UP” button▲ or ”Down” button▼ on the left side of the five functional buttons, the LCD will be showed as following: P A V O I C E : 6 0 % Note: After 3 seconds of pressing the button, the LCD will be automatically returned to the “MENU” page and save the settings automatically. 4.
Table-Top Delegate Mic CS-200DU Unit ○,1 ○,2 ○,3 ○,4 11 12 7 1 Talk Indicator lamp Status Indicator lamp Voting/Control Button & Indicator lamp ○,5 Voting Case Cover 10 2 Talk Button 4 3 4 Control 8 2 Talk 9 5 6 5 3 1 ○,6 Record Output Jack ○,7 Earphone Output Jack ○,8 Earphone Volume Control ○,9 LCD ○,10 MIC Jack ○,11 Built-In Speaker ○,12 Hidden Wiring Slot Functions： 53.6 169.3 131.8 131.8 12 1.
3. Lamp color definition of conference mode status. Red Light On：Chairman Mode Orange Light On： FIFO Mode Green Light On： Override Mode 4. Chairman Mode: While pressing the “TALK” button by the chairman, the ring of LED and talk indicator lamp of delegate microphones are flashing with RED color, once the chairman permits speaking, and the ring of LED will be automatically turned to red color without flashing, the delegates can speak now. 5.
3 : x x x 4 : x x x 5 : x x x 【T：Total voters】 【A：Abstained voters】 【1：Voters for No.1】 【2：Voters for No.2】 【3：Voters for No.3】 【4：Voters for No.4】 【5：Voters for No.5】 6.2.2Ballot: 6.2.2.1 Before voting, five lamps will be on simultaneously, which mean the voting can be executed. For strengthening the confidentiality, when you press the button, the corresponding red lamps will be flashing twice and then disappeared immediately which indicate the successful voting.
Table-Top Delegate Mic- CS-200DU Unit 8 9 7 4 3 Status 5 2 Talk 6 ○,1 Talk Button ○,2 Talk Indicator lamp ○,3 Control Indicator lamp ○,4 Record Output Jack ○,5 Earphone Output Jack ○,6 Earphone Volume Control ○,7 LCD ○,8 MIC Jack ○,9 Built-In Speaker ○,10 Voting Function Case ○,11 Hidden Wiring Slot 10 1 53.6 169.3 131.8 131.8 11 Functions: 1. CS-200DUB does not have the LCD screen, but the rest functions are as same as CS-200DU. 1.
3.1 Red Light On：Chairman Mode 3.2 Orange Light On： FIFO Mode 3.3 Green Light On： Override Mode 4. Chairman Mode: While pressing the “TALK” button by the chairman, the ring of LED and talk indicator lamp of delegate microphones are flashing with RED color, once the chairman permits speaking, and the ring of LED will be automatically turned to red color without flashing, the delegates can speak now. 5.
Before voting, five lamps will be on simultaneously, which mean the voting can be executed. For strengthening the confidentiality, when you press the button, the corresponding red lamps will be flashing twice and then disappeared immediately which indicate the successful voting. When voting is stopped, all five lamps will be start flashing which indicate the system is calculating the votes, once the calculation is finished, it will stop flashing. 7.
Table-Top Chairman Mic- CS-200CU Unit ○,1 ○,2 ○,3 ○,4 ○,5 11 12 10 Talk Button Talk Indicator lamp Chairman Control Button Status Indicator lamp Voting/Control Button & Indicator lamp ○,6 Voting Case Cover 7 1 4 2 3 4 Control 8 2 Talk 9 5 6 5 3 1 ○,7 Record Output Jack ○,8 Earphone Output Jack ○,9 Earphone Volume Control ○,10 LCD ○,11 MIC Jack ○,12 Built-In Speaker ○,13 Hidden Wiring Slot 53.6 169.3 131.8 131.8 13 Functions： 1.
4. Lamp color definition of conference mode status. 4.1 Red Light On：Chairman Mode 4.2 Orange Light On： FIFO Mode 4.3 Green Light On： Override Mode 5. Chairman Mode: Press “Control” button for three seconds until the red LED above the Control button is on and the MODE on the LCD displays Chairman and the chairman mode can be executed; vice verse, press Control button again for three seconds until the red LED above the Control button is off, it will resume to normal talking status. 6.
Table-Top Delegate Mic- CS-200DU Unit 8 9 7 4 3 Status Talk 5 2 6 ○,1 Talk Button ○,2 Talk Indicator lamp ○,3 Control Indicator lamp ○,4 Record Output Jack ○,5 Earphone Output Jack ○,6 Earphone Volume Control ○,7 LCD ○,8 MIC Jack ○,9 Built-In Speaker ○,10 Voting Function Expanded Case ○,11 Hidden Wiring Slot 10 1 53.6 169.3 131.8 131.8 11 Functions: 1. CS-200DUB does not have the LCD screen, but the rest functions are as same as CS-20DU. 1.
2. Press Talk button, when the indicator lamp of Talk and microphone is on, talking can begin. 3. Lamp color definition of conference mode status. 3.1 Red Light On：Chairman Mode 3.2 Orange Light On： FIFO Mode 3.3 Green Light On： Override Mode 4.
Appendix. Speed Dome Basic Setting 1.1 Power On & Off Before the speed dome connects with other equipments, user has to complete the related settings of IP address and protocols. Please see the following pictures: A Reserved port B Communication Switch C IP Address Switch D Protocol Switch E RJ-45 connecting port (for Speed Dome) F Data Transmission Connector (22-Pin Connector) 1.
RS-485 Communication Setting Half Duplex Full Duplex The factory setting of RS-485 is Half-Duplex. Note: Do not change the settings without the instructions of professional technicians. 1.3 IP Address IP address can be adjusted by the arrow on the switch. For example, IP address is”123.” Please adjust it with the order of Percentile (1), Decile (2) and Unit (3).
2.1 Telecom Protocol Switch No. Protocol Baud Rate 00 VCL 9600 01 Pelco D 2400 02 Pelco P 4800 04 Chiper 9600 05 Philips 9600 07 BXB 9600 08 AD422 4800 09 DM P 9600 11 Pelco D 4800 12 Pelco D 9600 13 Pelco P 2400 14 Pelco P 9600 15 JVC 9600 16 GANZ 9600 For example, if your protocol is “Pelco D”, the baud rate is 2400, Switch no is 01, and the setting is as follows: 2.
Data Transmission Cord: DC 12V Data Transmission Cord: AC 24V Please see the following 22-Pin DefinitionTable as connecting referenece.
